Kokido Xtovac 510 Pool Vacuum Cleaner

SAFETY WARNINGS & INSTRUCTIONS

Information contained in this Instruction Manual will help you operate the item safely, protect yourself and others from hazards, and prevent damage to the device and other property.

SAVE THESE INSTRUCTIONS

WARNING!

• This is not a TOY. Children should be kept out of reach from this pool vacuum and its accessories.
• Never allow children to operate this pool vacuum.
• This appliance is not intended for use by persons with reduced physical, sensory, mental capabilities, or a lack of experience and knowledge, unless they are given supervision or instructions concerning the safe use of the appliance and understand the hazards involved by a person responsible for their safety.
• Children must not play with this product.
• Cleaning and maintenance of the pool vacuum must not be carried out by children.
• Make sure the pool vacuum is fully immersed in the pool before initiating operation. The minimum water level required to operate the pool vacuum must reach above the power ON/OFF switch of the pool vacuum when it is held in a vertical position. Operating the pool vacuum when it is not immersed correctly could damage the unit and void the warranty.
• Maximum operating depth in water is 3 meters (9.8ft).
• Maximum water temperature: 5°C (41°F) – 42°C (107.6°F)
• DC Detachable supply unit (external adaptor).
• The pool vacuum should only be recharged with the external adaptor and charging base delivered with this product.
• For the purposes of recharging the battery, only use the detachable supply unit that provided with this pool vacuum to charge the battery.
• Connect the external adaptor to a power source through a residential current device (RCD) / a ground fault circuit interrupter (GFCI). If in doubt, consult a qualified electrician.
• Do NOT use this pool vacuum if any damage is detected.
• Replace damaged parts with ones that are certified by the distributor or manufacturer.
• Turn off the power, disconnect the external adaptor from the power source, and unplug the external adaptor from the charging base before detaching the pool vacuum from the charging base.
• Disconnect the pool vacuum from the supply mains and make sure the pool vacuum is OFF prior to carrying out regular maintenance – such as cleaning the filter and the charging contact plates.
• DO NOT attempt to replace the installed rechargeable Li-ion battery pack.
• DO NOT handle the pool vacuum, external adaptor, and charging base while it is charging with wet limbs and without shoes.
• Ensure that children do not attempt to access the pool vacuum while it is operating.
• DO NOT use this pool vacuum without an intact filter cone in place, as your warranty will be voided as a result.
• Suction entrapment hazard: This pool vacuum generates suction. Do not allow hair, body, or any loose parts of your clothing to make contact with the suction hole of the pool vacuum during its operation.
• Never insert body parts, clothing or other objects into the openings and moving parts of the pool vacuum.
• DO NOT use this pool vacuum to pick up any toxic substance, flammable, and combustible liquids (i.e. gasoline) in the presence of explosive or flammable fumes.
• Under no circumstances should you attempt to disassemble the pool vacuum and replace the impeller, motor, and battery by yourself.
• Never insert fingers or any object to touch the impeller.
• The built-in battery must be removed by a skilled technician before it is scrapped.
• This pool vacuum contains a battery that are only to be removed by skilled persons.
• The pool vacuum must be disconnected from the supply mains as the battery is removed.
• For details regarding battery recycling/disposal, refer to the section "BATTERY DISPOSAL" in this manual and contact your local authorities for more information.
• The battery must be disposed safely in accordance with local ordinances or regulations.
• External adaptor and charging base: Never use the external adaptor and charging base for anything other than charging the battery of the pool vacuum that is supplied in the same pack.
• The external adaptor and charging base should not be used outdoors, nor should it be exposed to rain, humidity, and any liquid or heat.
• Keep the external adaptor and charging base out of reach of children.
• Never use the external adaptor and charging base if any damage is detected.
• DO NOT handle the external adaptor and charging base with wet hands.
• DO NOT handle the pool vacuum, external adaptor, and charging base while charging with wet hands and without shoes.
• Keep the external adaptor disconnected from power when it is not in use.
• Never attempt to open the external adaptor and charging base.
• If the supply cord of the external adaptor is damaged, the external adaptor must be replaced by the manufacturer or its service agent to prevent hazards of any kind.
• Make sure the pool vacuum and the charging base are completely dry before charging.

CAUTION!

• This pool vacuum is designed for underwater use only; it is not an all-purpose vacuum cleaner. DO NOT attempt to use it to clean anything other than your pool.
• Use only original accessories delivered with this product.
• DO NOT use this pool vacuum right after pool-shocking. It is recommended to leave the pool circulating for at least 24-48 hours.
• If you are planning on using the pool vacuum in a saltwater pool, make sure all salt are dissolved before deploying the pool vacuum.
• DO NOT use this pool vacuum with another automatic cleaner/cleaner simultaneously in the pool.
• Avoid picking up hard, sharp objects with this product. They may damage the pool vacuum and filter.
• Exercise caution when cleaning pool stairs.
• To avoid damages to the external adaptor and charging base, do not attempt to carry the pool vacuum by the cord of external adaptor / charging base or pull the cord to disconnect it from the power source and charging base.
• Charge the pool vacuum indoor in a clean, dry area with good ventilation and an ambient temperature between 5°C (41°F) and 35°C (95°F).
• DO NOT leave the pool vacuum charged for over 10 hours.
• If the pool vacuum will not be used for an extended period, detach it from the charging base and use a damp cloth to clean and dry the pool vacuum and accessories. Make sure to charge the pool vacuum to about 30% to 50% of the battery capacity before it is stored. Store in a well-ventilated area away from sunlight, heat, ignition sources, pool chemicals, and children. Never leave the pool vacuum plugged in for long-term storage. Recharge the pool vacuum every three months.

Above warnings and cautions are not intended to incorporate all possible instances for risks and / or severe injuries. Pool / spa owners should always exercise extra caution and common sense when utilizing the product.

GETTING STARTED

Charging The Battery

IMPORTANT NOTE: Fully charge the pool vacuum (about 6 hrs) before using it for the first time.

WARNING!

• Use only the original external adaptor and charging base provided.
• Make sure the pool vacuum and the charging contact plates are clean and dry before set-up and charging. (TIPS: Use a cotton bud to dry the charging contact plates)
• Charging must be done indoors, in a well-ventilated area away from sunlight, children, heat, ignition sources, and with an ambient temperature between 5°C (41°F) and 35°C (95°F).
• Never use the external adaptor and charging base if any damage is detected.
• The charging contact plates are waterproof. However, remnants of water on the contact plates could result in natural occurrence of stains (a byproduct of chemical reaction between water and electric currents). Otherwise, the stains can be removed by light scrubbing with a cotton bud soaked with juice of lemon or vinegar.
• Make sure that the pool vacuum is turned off prior to charging.

1. Place the unit on a flat surface. Make sure the pool vacuum is off by turning the power ON/OFF switch to the OFF position prior to charging.
2. Align and slide the hook of the charging base onto the side notch at the bottom of the rear body until it stops. Make sure their contact plates are properly in contact. Plug the female jack of the external adaptor into the charging port at the end of the charging base.
3. Connect the external adaptor to the power source. Once the pool vacuum begins charging, the indicator light on the external adaptor will turn red. Normally, it takes about 5-6 hours to reach a full charge. The indicator light will turn green when the pool vacuum is almost fully charged.

NOTE: if the motor is generating noise, ensure “OFF” is selected on the power switch.

• Immediately disconnect the external adaptor from the power source if you detect any of the following:
  • Offensive or unusual odor
  • Excessive heat
  • Deformation, cracks, leaks
  • Smoke

4. When charging is complete, disconnect the external adaptor from the power source and detach the charging base from the unit and external adaptor.

Normally, the pool vacuum can operate up to 90 minutes on a full charge (charged for 5-6 hours).

Note: Clean the filter regularly. Excessive debris increases the burden to the motor operation and shortens the operating duration as a result.

FACT: Rechargeable lithium-Ion battery is classified as a consumable item. It has a limited life and will gradually lose its capacity to hold a charge. Therefore, running time of the pool vacuum will gradually reduce through repeated charging and discharging in operation. Once the lifespan of the battery reaches its end, refer to section "BATTERY DISPOSAL" for instructions regarding battery disposal.

NOTE: Let the pool vacuum rest for 30 to 40 minutes before charging it again.

Set-Up Before Use

Pole Connector Assembly

[Diagram showing pole connector assembly]

Telescopic Pole (Not Included) Assembly

[Diagram showing telescopic pole assembly]

Pool Preparation

• If there are stones, roots or metal corrosion in contact with the underside of the liner, discard them prior to using the pool vacuum. If necessary, seek assistance from a qualified professional.
• If the liner is brittle, damaged or wrinkled, contact a qualified professional to perform the necessary repairs or perform a liner replacement prior to using the pool vacuum.
• If you are using a saltwater pool, make sure all salt are dissolved before placing the pool vacuum into the water.

OPERATION

WARNING!

• Make sure the pool vacuum is off.
• Do not use the pool vacuum if any damage is detected.
• Oil stain could occur due to possible leakage of lubricants applied to the O-ring.
• Make sure the pool vacuum is fully immersed in the pool before initiating operation. The minimum water level required to operate the pool vacuum must reach above the power ON/OFF switch of the pool vacuum when it is held in a vertical position. Operating the pool vacuum when it is not immersed correctly could damage the unit and void the warranty.
• DO NOT use the pool vacuum without an intact filter cone in place. Using your pool vacuum without an intact filter cone in place will VOID your warranty.
• DO NOT cover the side slot of the vacuum during operation. The impeller / motor may be damaged as a result.
• DO NOT leave the pool vacuum in the water when it is not in use.
• Ensure the charging base is detached before the pool vacuum is deployed.

1. Bring your pool vacuum to the side of your pool / spa. Immerse the pool vacuum in water and turn the power ON/OFF switch to the ON position to initiate operation.

CAUTION! Make sure the pool vacuum is always facing downwards when it is placed into the pool. Otherwise it may bend the pole connector and damage it during the process.

2. To remove the pool vacuum from the pool, lift the pool vacuum while pointing it downwards in order to allow water to escape from the outlet valve. Water is going to escape via the handle / pole connector and draining holes inside the handle chamber on the rear body.

CAUTION! Make sure the pool vacuum is always facing downwards when it is removed from the pool. Otherwise, the pole connector may be bent and damage the pool vacuum in the process.

3. Rinse the pool vacuum with fresh water after every use. DO NOT use any detergent.

Emptying the filter

WARNING! Using the pool vacuum without a filter cone in place will VOID your warranty.

In order to maximize the cleaning efficiency, be sure to clean the filter cone before and after each use.

CAUTION! If the pool vacuum is charging, disconnect the external adaptor from the power source and detach the pool vacuum from the charging base. Make sure the pool vacuum is OFF.

1. Place the pool vacuum on a stable surface.
2. Hold the pool vacuum and pry up the canister lever to the end to completely release the side locks.
3. Detach the canister and use your finger to locate the notch on the handle of the cone base. Pry the handle to detach the filter cone from the canister.
4. Turn the cone base anticlockwise until the notches align with the tabs along the bottom of the cone, which will release the base from the cone.

CAUTION! Replace the damaged filter cone immediately before the next operation.

5. Clean out the debris and rinse the filter cone and its base with water. If brushing is deemed necessary, use only a soft brush to clean the filter cone gently and carefully.
6. Reverse the previous steps to reassemble the cone base to the cone, and then attach the filter cone to the canister. Additionally, it notes that when reinstalling the filter cone back into the canister, the ridges on the nozzle of the filter cone should face up.
7. Align and re-assemble the canister to the pool vacuum and make sure the lever is secured by pushing it down all the way to the hood.

MAINTENANCE & STORAGE

NOTE:

1. Be sure to clean and dry the charging contact plates after every use to avoid the forming of stains (byproduct of a natural chemical reaction between electric current and water). Otherwise, the stains can be removed by light scrubbing with a cotton bud soaked with juice of lemon or vinegar.
2. Battery discharges on its own during storage. Make sure to charge the pool vacuum to about 30% to 50% of the battery capacity before it is stored.
3. You must re-charge the battery at least once every three months when it is not in use.
   • Unplug the external adaptor from socket and then unplug the adapter jack from the charging base.
   • Detach accessories from the pool vacuum. If necessary, rinse the pool vacuum and accessories with fresh water. DO NOT use detergent.
   • Make sure to drain the water from the unit, handle and pole connector.
   • Use a damp cloth to clean and dry the pool vacuum and its accessories.
   • Store them in a well-ventilated area away from the sunlight, children, heat, ignition sources, and pool chemicals. Ambient temperature for storage should be 10°C – 25°C (50°F – 77°F). NOTE: A higher temperature may reduce the battery life during storage.

WARNING!

• Never attempt in any way to disassemble the pool vacuum.
• Under no circumstances should you attempt to disassemble the pool vacuum and replace the impeller, motor and battery by yourself.

CAUTION!

• Excessive heat can damage the battery and reduce its lifespan as a result.
• Consult your dealer regarding battery replacement if the following happens:
  • Battery does not charge fully.
  • Battery operation time is noticeably reduced. Observe and record the run times of the first few operations (on a full charge). Use these run times as a reference point for comparison with run times in the future.
  • The battery must be removed from the pool vacuum before it is scrapped.
  • The pool vacuum must be disconnected from the supply mains when removing the battery
  • The battery is to be disposed safely and according to local ordinances or regulations.

NOTE: Incorrect maintenance may reduce the battery life and affect its capacity as a result.

BATTERY DISPOSAL

(To be carried out by an authorized technician)

Your robot is equipped with a maintenance - free rechargeable lithium-ion battery pack, which must be disposed of properly. Recycling is required; please contact your local authority for more information.

WARNING! Never attempt to disassemble a battery pack.

• Remove all personal items such as rings, bracelets, necklaces and watches when the battery pack is unwired from the robot.
• A battery can produce a short circuit current high enough to weld a ring (or similar item ) to metal, causing a severe burn in the process.
• Wear complete eye protection, gloves and protective clothing when the battery pack is being removed.
• Avoid touching the wires altogether and avoid contact between them and any metal items, which could cause sparking and/or short circuit the battery.
• Never smoke or allow a spark or flame in the vicinity of the battery or the robot.
• Do not expose the battery to fire or intense heat as this may result in an explosion.

CAUTION!

• If a battery leak occurs, avoid any contact with the leaking fluids and place the damaged battery in a plastic bag.
• If leaking fluids come in contact with skin and clothing, wash immediately with plenty of soap and water.
• If leaking fluids come in contact with eyes, do not rub eyes, immediately flush eyes with cool running water for at least 15 minutes and do not rub them. Seek medical attention as soon as possible.

How to remove the battery pack for battery disposal only

(To be done by authorized technician)

Recommended tools (not included): Philips screwdriver.

1. Follow instructions to release the canister and filter cone. [Diagram showing canister and filter cone release]
2. Use small flat screwdriver to pry and remove the screw covers as shown. [Diagram showing screw cover removal]
3. Use the screwdriver to unscrew the 6 screws located on the top plate and then detach it from the rear body to expose the rear body's cover. [Diagram showing top plate screw removal]
4. Unfasten 6 screws and detach the cover to expose the PCBA, motor assembly, and battery pack. [Diagram showing cover removal to expose components]
5. To detach the battery connection wire, press the clip on the connector and then pull it out. [Diagram showing battery connection wire detachment]
6. Unfasten the 3 screws to remove the battery compartment cover and then remove the battery pack. [Diagram showing battery pack removal]

   NOTE: Wrap the connector immediately with insulating tape in order to avoid short circuit caused by contact of both wire terminals.

TROUBLESHOOTING

Environmental Programmes, WEEE European Directive

Please respect the European Union regulations and help to protect the environment. Return non-working electrical equipment to a facility appointed by your municipality that properly recycles electrical and electronic equipment. Do not dispose them in unsorted waste bins. For items containing removable batteries, remove batteries before disposing of the product.

All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of Kokido Development Ltd. (L-25005030)

We reserve the right to change all or part of the features of the articles or contents of this document, without prior notice. International patents pending

SAVE THESE INSTRUCTIONS

Manufacturer: Kokido Development Limited. Unit 1319, Sunbeam Centre, 27 Shing Yip Street, Kwun Tong, Kowloon, HK

EV057BRXUSAAAMZ

Support Email: support@kokido.com

Toll-Free Voicemail: (866) 683-7672

Download Instruction Manual & Videos: https://shop.kokido.com/pages/support-xtrovac-510

QR Code: [QR Code]

Made in China

FILTER SOCK ASSEMBLY

Note: A filter sock is provided for filtering fine particle, and it should be used together with the fine mesh filter cone base. Refer to the section “EMPTYING THE FILTER” for instructions on how to uninstall the filter cone and replace the filter base. Put the sock onto the cone and stretch it down to the end. Hook the sock edge onto the locking knobs along the filter cone.

[Diagrams for filter sock assembly]

SUCTION HEAD / NOZZLE ASSEMBLY

• Insert the suction head directly into the suction mouth of the pool vacuum until the side tabs of the transparent canister clip in the side holes of the suction head.
• WARNING! For spa, vinyl liner, and fiberglass pools, it is recommended to keep the brushes on the suction head to avoid damaging the pool/spa.

[Diagrams for suction head/nozzle assembly]