EDIC Fivestar Self-Contained Carpet Extractor 401TR User Manual

Introduction

The EDIC Fivestar Self-Contained Carpet Extractor 401TR is a compact, lightweight, and user-friendly machine designed for effective carpet maintenance. It prioritizes value to the customer by offering powerful cleaning capabilities in a manageable form factor. This manual provides comprehensive instructions for setting up, operating, and maintaining your Fivestar extractor to ensure optimal performance and longevity.

Figure 1: The EDIC Fivestar Self-Contained Carpet Extractor 401TR.

Setup

Portability and Transport

The Fivestar's compact and lightweight design facilitates easy loading and unloading from various vehicles. Its convenient, retractable handle not only saves storage space but also simplifies transport to the job site.

Figure 2: The Fivestar's compact design allows for easy transport by a single person.

Initial Preparation

1. Plug In: Simply plug the single power cord into a suitable electrical outlet.
2. Adjust Handle: Lock the adjustable handle in place at a comfortable height for operation.
3. Fill Solution Tank:
   • The Fivestar's solution and recovery tank is designed for easy removal. Lift the tank using its built-in carrying handle.
   • Take the tank to a sink or other water source.
   • For optimal cleaning effectiveness, fill the three-gallon solution tank with warm or hot water.
   • Cleaning chemicals can be added directly to the solution tank for quick spot or entryway cleanup.
   • Once filled, place the tank back onto the Fivestar base and close the self-sealing lid. The machine is now ready for use.

Figure 3: Top view of the Fivestar showing the solution and recovery tanks.

Pre-treatment (Optional)

Before cleaning, you may apply a chemical pre-spray directly to the carpet. For maintenance cleaning, EDIC recommends applying a pre-spray and allowing it to dwell for 5 to 10 minutes before scrubbing and rinsing with the Fivestar. For difficult spots and high-traffic lanes, you might need to agitate the chemical into the carpet fibers using a carpet brush or rake.

Operation

Mode Selection

Before beginning, ensure the mode switch on the lower right side of the Fivestar is set to the correct position for the surface you are cleaning (e.g., Carpet or Floor).

Figure 4: Side view of the Fivestar, showing the mode switch location.

Control Panel

The controls are conveniently located on the handle for easy access and are sealed to protect them from water damage.

• To begin cleaning, turn on the Vacuum, Brush (agitator), and Pump switches (set to either Carpet or Upholstery as needed).
• Hold down the Activate button on the handle to apply solution and engage the agitator brush.

Figure 5: Close-up of the Fivestar's control panel on the handle.

Cleaning Procedure

Clean by pulling the Fivestar backward. It is recommended to overlap passes slightly to ensure full cleaning coverage. The Fivestar is designed to reach into corners and maintain high productivity.

Dry Pass

To remove additional water from the carpet, perform a dry pass. Simply release the Activate button and go over the cleaned area using only the vacuum function.

Maintenance

Emptying the Recovery Tank

When the recovery tank is full and requires emptying:

1. Turn off the machine.
2. Remove the recovery tank using its built-in handle.
3. Take the recovery tank to a toilet or designated disposal area and empty it. The patented bladder design ensures that dirty water does not contaminate the clean water supply.

Accessing Internal Components

Accessing the equipment bay for maintenance is straightforward:

1. Remove the two caps on the front of the machine to reveal the screws.
2. Using a Phillips head screwdriver, remove the screw on the left and the screw on the right of the machine.
3. Once the screws are removed, gently tilt the machine backward from the handle to open the equipment bay.

Inside, you will find a well-organized layout of components, including the 50 PSI solution pump, the upright-mounted two-horsepower vacuum motor with 112 CFM, and the brush motor providing cleaning power at 2500 RPM. All these components feature quick connects for easy service and replacement. The exclusive intercooler system helps keep all electrical components cool, ensuring many years of reliable operation.

Figure 6: View of the Fivestar's internal components, including the pump and motor.

Troubleshooting

For common operational issues, please refer to the troubleshooting section in the full product manual or contact customer support. Ensure all connections are secure, tanks are properly filled/emptied, and power is supplied correctly.

Specifications

Warranty & Support

For information regarding product warranty, please refer to the documentation included with your purchase or contact EDIC customer support directly. Customer support is available to assist with any questions or issues you may encounter.