Globe Electric 469036 Indoor Digital Timer User Manual

1. Introduction

Thank you for choosing the Globe Electric 469036 Indoor Digital Timer. This device is designed to provide convenient and energy-efficient control over your indoor electrical appliances. With its 7-day programmable features and to-the-minute accuracy, you can automate your home or office lighting and other devices with ease. Please read this manual thoroughly before operation to ensure proper use and safety.

2. Safety Information

Always observe the following safety precautions when using electrical devices:

• Do not immerse the timer in water or any other liquid.
• Do not use the timer outdoors or in wet locations.
• Ensure the timer is properly grounded. The timer features a grounded outlet for protection against short circuits.
• Do not exceed the maximum electrical rating of the timer. Refer to the specifications section for details.
• Do not disassemble or attempt to repair the timer yourself. Contact qualified service personnel for repairs.
• Keep out of reach of children.
• Unplug the timer from the wall outlet before cleaning.

3. Product Overview

Familiarize yourself with the components of your Globe Electric Digital Timer:

Figure 3.1: Front view of the Globe Electric 469036 Indoor Digital Timer, showing the digital display, and six blue buttons labeled DAY, HOUR, MIN, CLK, MODE, and PRG, with a RESET button below them.

Components:

• Digital Display: Shows current time, day, and programming settings.
• DAY Button: Used to set the day of the week.
• HOUR Button: Used to set the hour.
• MIN Button: Used to set the minute.
• CLK (Clock) Button: Used to view the current time or exit programming mode.
• MODE Button: Used to cycle through different operating modes (e.g., ON, OFF, AUTO).
• PRG (Program) Button: Used to enter and navigate through programming settings.
• RESET Button: Resets all settings to factory defaults. (Often recessed, requires a pointed object to press).
• Grounded Outlet: Located on the front, where the appliance is plugged in.

4. Setup

4.1 Initial Setup

1. Unpack the timer and inspect it for any damage.
2. Plug the timer into a standard 120V AC wall outlet.
3. The display should light up. If it does not, ensure the outlet is live.
4. It is recommended to press the RESET button (using a pen or paperclip) upon first use or after a prolonged period of disuse to clear any previous settings.

4.2 Setting the Current Time and Day

To set the current time and day:

1. Press and hold the CLK button.
2. While holding CLK, press the DAY button repeatedly until the correct day of the week is displayed.
3. While still holding CLK, press the HOUR button repeatedly to set the correct hour (note AM/PM if applicable).
4. While still holding CLK, press the MIN button repeatedly to set the correct minute.
5. Release the CLK button. The time and day are now set.

5. Operating Instructions

5.1 Programming ON/OFF Times

The timer allows for multiple ON/OFF programs. Follow these steps to set a program:

1. Press the PRG button once. The display will show "1 ON" and the time will flash.
2. Press DAY repeatedly to select the day(s) for this program. Options include individual days, weekdays, weekends, or all 7 days.
3. Press HOUR and MIN to set the desired ON time for "1 ON".
4. Press PRG again. The display will show "1 OFF" and the time will flash.
5. Press DAY repeatedly to select the day(s) for this OFF program (usually the same as the ON program).
6. Press HOUR and MIN to set the desired OFF time for "1 OFF".
7. To set additional programs (e.g., "2 ON", "2 OFF"), repeat steps 1-6, pressing PRG to advance to the next program number. The timer supports up to 10 ON/OFF programs.
8. Once all programs are set, press the CLK button to return to the current time display.

5.2 Setting Operating Mode (AUTO/ON/OFF)

After programming, ensure the timer is in the correct operating mode:

• Press the MODE button repeatedly to cycle through the following options:
  • AUTO ON: The timer will follow the programmed ON/OFF times. If the current time is within an ON period, the connected appliance will be ON.
  • AUTO OFF: The timer will follow the programmed ON/OFF times. If the current time is within an OFF period, the connected appliance will be OFF.
  • ON: The connected appliance will remain ON continuously, overriding all programs.
  • OFF: The connected appliance will remain OFF continuously, overriding all programs.
• For automatic operation, select either AUTO ON or AUTO OFF depending on the current state you desire before the next programmed event.

5.3 Manual Override

While in AUTO mode, you can temporarily override the current ON/OFF state by pressing the MODE button. For example, if the timer is in AUTO OFF and you want to turn the appliance ON, press MODE once to switch to ON. The timer will then revert to AUTO mode at the next programmed event.

6. Maintenance

The Globe Electric Digital Timer requires minimal maintenance.

• Cleaning: Unplug the timer from the wall outlet. Wipe the exterior with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Storage: If storing the timer for an extended period, unplug it and keep it in a cool, dry place.

7. Troubleshooting

8. Specifications

• Model: 469036
• Type: Indoor Digital Timer
• Color: White
• Material: Plastic
• Dimensions: 6.1 x 11.18 x 13.72 cm (2.4 x 4.4 x 5.4 inches)
• Weight: 22.7 g (0.05 lbs)
• Number of Settings: Up to 10 ON/OFF programs
• Power: 120V AC, 60Hz (Specific amperage/wattage not provided in source, general timer info usually implies standard household load)
• Grounding: Grounded outlet
• UPC: 050428135587

9. Warranty and Support

For warranty information or technical support, please contact Globe Electric customer service. Refer to the product packaging or the Globe Electric website for the most current contact details and warranty policy.

Note: Specific warranty terms may vary by region and purchase date. Please retain your proof of purchase.