Intel E97379-001 CPU Cooler User Manual

1. Product Overview

The Intel E97379-001 CPU Cooler is designed to provide efficient cooling for Intel Core i3, i5, and i7 processors compatible with Socket 1150, 1155, and 1156 motherboards. This cooler features an aluminum heatsink and a 3.5-inch (90 mm) fan with a 4-pin power connector for controlled operation.

Image 1.1: Top view of the Intel E97379-001 CPU Cooler, showing the fan and heatsink fins.

Key features include:

• Aluminum heatsink for effective heat dissipation.
• 3.5-inch (90 mm) fan operating at DC 12V, 0.17A.
• Supports Intel Core i3 processors up to 3.06 GHz (and compatible i5/i7 processors for specified sockets).
• 4-pin power connector for Pulse Width Modulation (PWM) fan speed control.
• Regulatory Approvals: UL, CE.

Image 1.2: Bottom view of the Intel E97379-001 CPU Cooler, showing the aluminum heatsink base and mounting pins.

2. Setup and Installation

Follow these steps carefully to install the Intel E97379-001 CPU Cooler onto your compatible motherboard.

2.1 Preparing the Fan

1. Ensure the fan power cord is organized and clear of the fan blades. Avoid any contact between the cord and the fan during operation.

Image 2.1: Ensure fan cables are neatly organized and secured to prevent interference with fan blades.

2.2 Adjusting Fan Position and Alignment

2. Before installation, ensure the fan's mounting clips are in the correct, unlatched position.
3. Carefully place the CPU cooler horizontally over the processor. Align the four mounting buckles (pins) with the corresponding pinholes on the motherboard, which are located around the CPU socket.
4. Verify that the original fan's rotary switches (if applicable) are fully restored to their home position (the dot should be next to the fan position) before attempting to install.

Image 2.2: Align the cooler's mounting pins with the motherboard's CPU socket holes.

2.3 Securing the Cooler

4. The fan is designed with four clips. To ensure even pressure and proper seating, press down on the clips diagonally. For example, press the top-left clip, then the bottom-right, followed by the top-right, and finally the bottom-left. Press firmly until you hear a distinct 'snap' for each clip, indicating it is securely latched. Sequential pressing of adjacent clips can lead to uneven force and improper installation.
5. After securing the cooler, connect the 4-pin fan power cable to the designated CPU FAN header on your motherboard. This header typically provides power and allows for PWM fan speed control.

Image 2.3: Press clips diagonally until they snap into place, then connect the 4-pin power cable to the motherboard.

3. Operating Instructions

Once installed, the Intel E97379-001 CPU Cooler operates automatically. The 4-pin connector allows the motherboard to control the fan speed based on CPU temperature, optimizing cooling performance and noise levels.

• Automatic Speed Control: The fan speed will adjust dynamically. At lower CPU temperatures, the fan will spin slower, reducing noise. As CPU temperature rises under load, the fan speed will increase to provide more airflow and cooling.
• Monitoring: You can monitor CPU temperature and fan speed using motherboard monitoring software or BIOS/UEFI settings. Refer to your motherboard's manual for specific instructions.

4. Maintenance

Regular maintenance ensures optimal performance and longevity of your CPU cooler.

4.1 Cleaning

• Dust Removal: Periodically inspect the heatsink fins and fan blades for dust accumulation. Dust can impede airflow and reduce cooling efficiency.
• Cleaning Method: Use compressed air to gently blow dust out of the heatsink fins. Hold the fan blades to prevent them from spinning rapidly during cleaning, which can damage the fan motor.
• Frequency: Cleaning frequency depends on your environment. In dusty environments, more frequent cleaning (e.g., every 3-6 months) may be necessary.

4.2 Thermal Paste

• The cooler comes with pre-applied thermal paste. If you remove the cooler for any reason, it is recommended to clean off the old thermal paste from both the CPU and the cooler's base and apply a fresh layer of high-quality thermal paste before reinstallation.

4.3 Disassembly

To remove the CPU cooler:

1. First, disconnect the 4-pin power cable from the motherboard.
2. Rotate the raised point on the top of each clip post counter-clockwise. This will unlatch the clips.
3. Once all four clips are unlatched, gently lift the cooler straight up from the CPU. Avoid twisting or pulling forcefully to prevent damage to the CPU or motherboard socket.

5. Troubleshooting

• Fan Not Spinning:
  • Check if the 4-pin power connector is securely plugged into the CPU FAN header on the motherboard.
  • Ensure the system is powered on.
  • Verify fan settings in BIOS/UEFI. Some motherboards may have fan control settings that can disable the fan at low temperatures.
• High CPU Temperatures:
  • Ensure the cooler is properly seated and all four clips are securely latched. Uneven pressure can lead to poor thermal contact.
  • Check for excessive dust buildup on the heatsink fins and fan blades. Clean if necessary.
  • Verify that thermal paste is correctly applied and has not dried out. Reapply if needed.
  • Confirm that the fan is spinning at an appropriate speed. If it's running too slow, check BIOS/UEFI fan control settings.
• Excessive Noise:
  • Check for any cables or obstructions hitting the fan blades.
  • Ensure the fan is securely mounted and not vibrating against other components.
  • Dust buildup can sometimes cause imbalance and noise; clean the fan.

6. Specifications

7. Warranty and Support

This Intel CPU cooler typically comes with a standard manufacturer's warranty. For specific warranty details, including duration and coverage, please refer to the documentation provided with your processor or contact Intel customer support directly. Keep your proof of purchase for warranty claims.

For technical assistance or further inquiries, please visit the official Intel support website or contact their customer service.