Moen CA87060SRS High-Arc Kitchen Faucet with Side Spray User Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Moen CA87060SRS High-Arc Kitchen Faucet with Side Spray from the Caldwell Collection. This faucet features a Spot Resist Stainless finish, two-handle lever operation, and a Duralock quick connect system for simplified setup. Please read this manual thoroughly before beginning installation or use to ensure proper function and longevity of your product.

Figure 1: Moen CA87060SRS High-Arc Kitchen Faucet with Side Spray. This image displays the complete faucet assembly, including the high-arc spout, two lever handles, base plate, and the side spray connection points.

2. Safety Information

• Always turn off the main water supply before installing or servicing the faucet.
• Wear appropriate personal protective equipment, such as safety glasses, during installation.
• Ensure all connections are secure to prevent leaks.
• If you are unsure about any part of the installation process, consult a qualified plumber.
• Do not use harsh chemicals or abrasive cleaners on the faucet finish, as this may damage the Spot Resist Stainless surface.

3. Package Contents

Verify that all components are present before beginning installation:

• High-Arc Kitchen Faucet Assembly
• Side Spray Unit
• Mounting Hardware
• Installation Instructions (this manual)

4. Tools Required (Not Included)

• Adjustable Wrench
• Phillips Head Screwdriver
• Plumber's Putty or Silicone Sealant
• Flashlight (for under-sink work)
• Bucket and Towel (for water drainage)

5. Installation Instructions

This faucet is designed for deck mount installation, typically requiring four holes in the sink or countertop.

5.1. Prepare the Installation Area

1. Turn off the hot and cold water supply valves under the sink.
2. Remove any existing faucet and clean the mounting surface thoroughly.
3. Ensure the four mounting holes are clear and properly sized for the faucet and side spray.

5.2. Install the Faucet Body

1. Apply a thin bead of plumber's putty or silicone sealant around the base of the faucet body or the escutcheon plate, if applicable.
2. Insert the faucet body and handles into the designated holes on the sink or countertop.
3. From underneath the sink, secure the faucet using the provided mounting hardware. Hand-tighten first, then use an adjustable wrench to snug connections without overtightening.

5.3. Install the Side Spray

1. Insert the side spray hose through its designated hole in the sink or countertop.
2. From underneath, connect the side spray hose to the faucet's spray port using the Duralock quick connect system. Ensure a secure click indicates proper connection.
3. Secure the side spray base with its mounting hardware.

5.4. Connect Water Supply Lines

1. Connect the hot and cold water supply lines from the faucet to the corresponding hot and cold water supply valves. Use an adjustable wrench to tighten connections, being careful not to overtighten.
2. Ensure all connections are leak-free.

5.5. Test the Faucet

1. Slowly turn on the hot and cold water supply valves.
2. Check for any leaks at all connection points.
3. Turn on the faucet handles to flush the lines and check water flow and temperature.
4. Test the side spray for proper function.

6. Operation

The Moen CA87060SRS faucet features two lever handles for precise control of water temperature and flow.

• Water Flow: Lift the lever handles to increase water flow. Push down to decrease or turn off.
• Temperature Control: The left handle controls hot water, and the right handle controls cold water. Adjust both handles to achieve the desired water temperature.
• Side Spray: Squeeze the trigger on the side spray unit to divert water from the main spout to the spray. Release the trigger to return water flow to the main spout.

7. Maintenance

7.1. Cleaning the Finish

The Spot Resist Stainless finish is designed to resist fingerprints and water spots. To maintain its appearance:

• Clean with a soft, damp cloth and mild soap.
• Rinse thoroughly with clean water and dry with a soft cloth to prevent water spotting.
• Avoid abrasive cleaners, harsh chemicals, or polishing waxes, as these can damage the finish.

7.2. Aerator Cleaning

If water flow decreases or becomes irregular, the aerator may be clogged with debris.

1. Unscrew the aerator from the tip of the spout.
2. Rinse any debris from the aerator screen. For stubborn mineral deposits, soak the aerator in a 50/50 solution of white vinegar and water.
3. Reattach the aerator to the spout, ensuring it is securely tightened.

8. Troubleshooting

9. Specifications

• Model: CA87060SRS
• Brand: Moen
• Finish Type: Spot Resist Stainless
• Material: Metal (Handle Material: Stainless Steel)
• Mounting Type: Deck Mount
• Number of Handles: 2
• Hole Count: 4
• Spout Design: High Arc
• Spout Height: 13.66 Inches
• Spout Reach: 8.88 Inches
• Product Dimensions: 1"D x 1"W x 13.66"H
• Item Weight: 4.39 pounds
• Compliance: Complies with Americans with Disabilities Act (ADA) specifications. Meets current legislation, including AB1953 (California) and S152 (Vermont).

10. Warranty and Support

Moen products are manufactured under the highest standards of quality and workmanship. Moen offers a comprehensive warranty on its products. For specific warranty details, please refer to the warranty card included with your product or visit the official Moen website.

If you require assistance with installation, parts, or troubleshooting, please contact Moen Customer Support:

• Website: www.moen.com
• Phone: Refer to the Moen website for regional contact numbers.

Please have your model number (CA87060SRS) and date of purchase available when contacting support.