Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your GROHE Geneva Tub Spout. Please read this manual thoroughly before beginning installation to ensure proper function and longevity of the product. Retain this manual for future reference.
Safety Information
Important: Always turn off the main water supply before installing or servicing the tub spout. Failure to do so may result in water damage or personal injury.
- Ensure all local plumbing and building codes are followed.
- If you are unsure about any part of the installation process, consult a qualified plumber.
- Wear appropriate personal protective equipment (PPE) such as safety glasses and gloves during installation.
- Do not use harsh chemicals or abrasive cleaners on the product finish.
Package Contents
Verify that all components are present before beginning installation:
- GROHE Geneva Tub Spout (Model 13612000)
- Installation hardware (e.g., mounting plate, screws, seals) - Specific items may vary; refer to the diagram in your physical package.
Setup and Installation
The GROHE Geneva Tub Spout is designed for wall-mount installation with a 3/4-inch inlet. Follow these steps for proper setup:
- Prepare the Installation Area: Ensure the water supply is turned off. Clear the area around the existing tub spout or the intended installation point on the wall.
- Remove Existing Spout (if applicable): If replacing an old spout, carefully remove it. Clean any debris or old sealant from the wall and pipe.
- Install Mounting Hardware: Attach the mounting plate or adapter to the wall pipe according to the specific instructions provided with your hardware. Ensure it is securely fastened and level.
- Apply Sealant: Apply a bead of plumber's putty or silicone sealant around the base of the tub spout where it will meet the wall to prevent water penetration.
- Attach the Tub Spout: Carefully slide the GROHE Geneva Tub Spout onto the wall pipe, aligning it with the mounting hardware. Secure the spout in place using the set screw or other fastening mechanism. Ensure a tight, leak-free connection.
- Test for Leaks: Once the spout is securely installed, slowly turn on the main water supply. Check for any leaks around the base of the spout and the pipe connection. If leaks are detected, turn off the water, tighten connections, and re-test.
Image: The GROHE Geneva Tub Spout, showcasing its polished Grohe StarLight Chrome finish and traditional design. This wall-mounted spout has a 6-inch reach.
Operating the Tub Spout
The GROHE Geneva Tub Spout functions as a water outlet for your bathtub. Water flow is controlled by your bath faucet's handles (not included). To operate:
- Turn on the hot and/or cold water supply using your bath faucet handles.
- Water will flow from the tub spout into the bathtub.
- To divert water to a showerhead (if applicable and connected to a diverter valve), pull up or push down the diverter knob on your bath faucet or diverter valve. The Geneva Tub Spout itself does not include a diverter.
Maintenance
To maintain the beauty and performance of your GROHE Geneva Tub Spout, follow these care instructions:
- Cleaning: Clean the spout regularly with a soft cloth and mild soap or a non-abrasive cleaner specifically designed for chrome finishes.
- Avoid Harsh Cleaners: Do not use abrasive cleaners, scouring pads, ammonia-based cleaners, or cleaners containing bleach, acids, or alcohol, as these can damage the Grohe StarLight Chrome finish.
- Drying: After cleaning, rinse thoroughly with clean water and dry with a soft cloth to prevent water spots and maintain the shine.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Water leaks from the base of the spout. | Loose connection or insufficient sealant. | Turn off water supply. Tighten the spout's connection to the wall pipe. Reapply plumber's putty or silicone sealant if necessary. |
| Reduced water flow from the spout. | Debris in the water line or aerator (if applicable). | Check your main water supply pressure. If the spout has an aerator, remove and clean it. Consult a plumber if the issue persists. |
| Finish appears dull or stained. | Hard water spots or improper cleaning. | Clean with a soft cloth and mild soap. Dry thoroughly after each use. Avoid abrasive cleaners. |
Specifications
- Model: GROHE Geneva Tub Spout 13612000
- Finish: Grohe StarLight Chrome (Polished)
- Mounting Type: Wall Mount
- Inlet Size: 3/4 inch
- Spout Reach: 6 inches
- Style: Traditional
- Item Weight: 1.7 Pounds
- Code Compliance: ASME/ANSI A112.18.1M
Warranty and Support
GROHE products are manufactured to the highest quality standards. This product is covered by a Limited Lifetime Warranty (U.S.A Only) and a Lifetime Finish Warranty. For detailed warranty information, please refer to the official GROHE warranty documentation or visit the official GROHE website.
For technical support, replacement parts, or further assistance, please contact GROHE customer service. Contact information can typically be found on the official GROHE website or on the product packaging.