GE Personal Security Deluxe Door Alarm (Model 45117) Instruction Manual

Introduction

The GE Personal Security Deluxe Door Alarm (Model 45117) provides a simple, cost-effective security solution for your home, apartment, dorm room, or office. This wire-free device features a magnetic sensor and a 120-decibel alarm to deter unauthorized entry. It includes a four-digit keypad for custom PIN programming and offers both instant and delayed alarm modes.

Package Contents

• GE Personal Security Deluxe Door Alarm Unit (with keypad)
• Magnetic Sensor Strip
• Mounting Screws
• Double-sided Mounting Tape
• Instruction Manual

Setup

1. Battery Installation

The alarm requires 3 AAA batteries (not included). Locate the battery compartment on the back of the main alarm unit. Use a Phillips head screwdriver to open the compartment, insert the batteries, and secure the cover.

2. Setting Your Custom PIN

To program your personal 4-digit PIN:

1. With the battery compartment open, press and hold the small programming button located inside.
2. While holding the button, enter your desired 4-digit code using the keypad.
3. Release the programming button. Your PIN is now set.

3. Mounting the Alarm

The alarm can be mounted using either the included screws or double-sided tape. Ensure the main alarm unit and the magnetic sensor strip are aligned correctly on the door and door frame, respectively. The magnetic strip should be positioned no more than 0.5 inches from the main unit when the door is closed.

Image: The main alarm unit and magnetic sensor with dimensions. The alarm unit measures approximately 3.86 inches in height, 2.44 inches in width, and 1.25 inches in depth. The magnetic sensor measures approximately 2.0 inches in height, 0.56 inches in width, and 0.5 inches in depth. The alarm requires 3 AAA batteries (not included).

Image: Close-up of the GE Personal Security Deluxe Door Alarm with key components labeled: Home/Away Switch, Alarm/Chime Switch, Indicator Lights, and Keypad.

Image: The alarm unit and magnetic sensor demonstrating that the 120-decibel chime or alarm will trigger when the magnet separates from the base by more than 0.5 inches.

Image: The GE Personal Security Deluxe Door Alarm installed on a door frame next to a door. The keypad allows you to set a personal 4-digit code for arming and disarming the alarm.

Operating Instructions

Mode Selection

Use the slide switch on the side of the alarm unit to select the desired mode:

• OFF: The alarm is deactivated.
• CHIME: The unit will emit a chime sound when the door is opened.
• ALARM: The unit will sound a 120-decibel alarm when the door is opened.

Arming and Disarming

• AWAY Mode: When set to ALARM mode, the unit provides a 45-second exit delay after arming. Upon returning, you have 30 seconds to enter your 4-digit PIN to deactivate the alarm before it sounds. The indicator light will blink red for several seconds after arming, then turn green when armed.
• HOME Mode: When set to ALARM mode, the alarm will sound instantly if the door is opened. This mode is suitable when you are inside the home and want immediate alerts.
• To disarm the alarm, enter your 4-digit PIN.

Video Demonstrations

Features

• High-Decibel Alarm: Provides a 120-decibel alarm triggered by a magnetic sensor.
• User-Friendly Keypad: Features a four-digit keypad for custom PIN entry.
• Flexible Modes: Easy-access switch to choose between delayed (AWAY) or instant (HOME) chime/alarm modes.
• Easy Installation: Completely wire-free design with options for screw or double-sided tape mounting.
• Battery Operated: Powered by 3 AAA batteries (not included).
• Battery Indicator: Includes a battery test switch and low battery indicator.

Image: An illustration showing the GE Personal Security Deluxe Door Alarm sounding, with a person attempting to enter through a door, demonstrating its crime deterrence capability.

Maintenance

Battery Replacement

When the low battery indicator illuminates, replace the 3 AAA batteries promptly to ensure continuous operation. Follow the battery installation steps in the Setup section.

Battery Test

Use the battery test switch to check the current power levels of the batteries.

Troubleshooting

• Alarm not sounding: Ensure the magnetic sensor is within 0.5 inches of the main unit when the door is closed. Check battery levels and replace if necessary. Verify the mode switch is set to ALARM.
• False alarms: Check the alignment of the main unit and magnetic sensor. Ensure they are securely mounted and not shifting.
• PIN not working: Re-enter your 4-digit PIN carefully. If issues persist, try resetting the PIN following the instructions in the Setup section.

Specifications

Image: The back of the product packaging, detailing features such as Away mode, 4-digit keypad, 120dB alarm, versatile mounting, and low battery indicator. It also includes important safety warnings.

Safety Information

WARNING: Prolonged exposure to the alarm siren may cause permanent hearing loss. Exercise caution when testing the alarm.

Remove batteries before storing the unit for extended periods. Batteries may leak harmful liquids or explode if improperly installed or disposed of, causing injury and product damage. Do not mix old and new or other battery types. Replace all batteries at the same time. Remove fully discharged batteries immediately.

Warranty and Support

This product comes with a 1 Year Limited Warranty. For detailed warranty information and support, please refer to the official GE or Jasco Products website.

GE is a trademark of General Electric Company and is used under license by Jasco Products Company LLC.