Contents
hide
AFL FAST-SC-SM-6 Connect Single Mode
Product Information
- FASTConnect connectors are factory pre-polished and field-installable connectors that eliminate the need for hand polishing.
- They ensure precision fiber alignment, offer low-loss termination for single-mode and multimode optical fibers and come with a factory pre-cleaved fiber stub.
- FUSEConnect utilizes fusion splicing technology to terminate connectors in the field, providing true APC performance for SC/APC and LC/APC configurations.
- They are compatible with Fujikura fusion splicers and most other fiber-holder-based fusion splicing platforms.
Product Usage Instructions
FASTConnect Connector Usage
- Identify the cable size for termination (4.8 mm).
- Select the appropriate connector type and quantity based on your requirements.
- Remove the factory-installed wedge clip from the connector upon completion of termination.
- Use a Visual Fault Identifier (VFI) to confirm physical contact once the translucent wedge is engaged.
FUSEConnect Connector Usage
- Utilize a fusion splicer to terminate the connector in the field.
- Select the correct connector boot type based on the cable size and connector type needed.
- Follow fusion splicing procedures for optimal performance.
FAQ
Q: What is the difference between FASTConnect and FUSE Connect?
A: FASTConnect connectors are pre-polished field-installable connectors that eliminate hand polishing, while FUSEConnect utilizes fusion splicing technology for the termination in the field.
INTRODUCTION
FASTConnect® Field Installable Connectors
- FASTConnect is factory-polished, field-installable connectors that eliminate the need for hand polishing in the field.
- Proven mechanical splice technology ensuring precision fiber alignment, a factory pre-cleaved fiber stub, and a proprietary index-matching gel combine to offer an immediate low-loss termination to either single-mode or multimode optical fibers.
- FASTConnect is compatible with 250 µm and 900 µm optical fibers, as well as 2.0 mm, 3.0 mm, and 4.8 mm (SC only) cordage.
- All primary fiber types are supported and each connector is color-coded per industry-standard requirements to aid in identification during and after installation.
- A factory-installed wedge clip (included with each connector) is removed and discarded upon completion of the termination.
- Incorporated into this device is an innovative, translucent wedge enabling the use of a common VFI to provide a “pass/fail” signal once physical contact is achieved.
FEATURES
- Pre-stubbed, factory-polished ferrule
- No epoxy required
- Precision mechanical alignment ensures low-loss
- Fiber can be reseated
SPECIFICATIONS
| PARAMETERS | INSERTION LOSS | RETURN LOSS AT ROOM TEMPERATURE | OPERATING TEMPERATURE | ||
| AVERAGE (DB) | MAXIMUM (DB) | AVERAGE (DB) | MAXIMUM (DB) | ||
| SM UPC | 0.2 | 0.5 | ≤ -50 | ≤ -45 | -40 to +75°C |
| SM APC-AU* | 0.3 | 0.6 | ≤ -55 | ≤ -50 | -40 to +75°C |
| MM PC | 0.1 | 0.5 | ≤ -25 | ≤ -20 | -40 to +75°C |
AU denotes angled polish with a flat cleaved fiber
APPLICATIONS
- Premise environments
- Connections at the desk for LAN environments
- Patch panels
- Direct equipment termination
ORDERING INFORMATION
For cable size: 900 µm
| CONNECTOR TYPE | QTY/PACK | AFL NO. | ||||
| UPC SM (BLUE) | APC SM-AU (GREEN) | PC 62.5 μm MM (BEIGE) | PC 50 μm MM (BLACK) | PC 50 μm LOMMF (AQUA) | ||
| SC | 6 | FAST-SC-SM-6 | FAST-SC-SMAU-6 | FAST-SC-MM62.5-6 | FAST-SC-MM50-6 | FAST-SC-MM50L-6 |
| 100 | FAST-SC-SM-100 | FAST-SC-SMAU-100 | FAST-SC-MM62.5-100 | FAST-SC-MM50-100 | FAST-SC-MM50L-100 | |
| ST | 6 | FAST-ST-SM-6 | N/A | FAST-ST-MM62.5-6 | FAST-ST-MM50-6 | FAST-ST-MM50L-6 |
| 100 | FAST-ST-SM-100 | N/A | FAST-ST-MM62.5-6 | FAST-ST-MM50-100 | FAST-ST-MM50L-100 | |
| LC | 6 | FAST-LC-SM-6 | N/A | FAST-LC-MM62.5-6 | FAST-LC-MM50-6 | FAST-LC-MM50L-6 |
| 100 | FAST-LC-SM-100 | N/A | FAST-LC-MM62.5-100 | FAST-LC-MM50-100 | FAST-LC-MM50L-100 | |
For cable size: 4.8 mm
|
SC |
6 | N/A | FAST-SC48-SMAU-6 | N/A | N/A | N/A |
| 100 | N/A | FAST-SC48-SMAU-100 | N/A | N/A | N/A |
- Boot kits are available for 2.0 mm/3.0 mm Simplex cordage
- Requires FAST APC Tool Kit for installation
- AFL NO. is for one pack of 6 pieces
- Laser Optimized Multi-Mode Fiber (LOMMF) compatible with OM3 and OM4 fibers
FUSEConnect® Fusion Spliced, Field Installable Connectors
- Uniquely designed, the factory pre-polished ferrule eliminates the need for polishing, adhesives, and crimping in the field, which minimizes the potential for operator error and expensive connector scrap.
- FUSEConnect utilizes a fusion splicer to terminate the connector in the field, addressing return loss concerns present in analog optical networks.
- This advanced process yields true APC performance for SC/APC and LC/APC configurations. FUSEConnect is compatible with Fujikura fusion splicers and most other fiber-holder-based fusion splicing platforms.
FEATURES
- Field installable splice on connector
- No adhesives, crimping, or polishing
- True APC performance
- Compatible with most fusion splicers
APPLICATIONS
- RF-overlay TP networks
- Cable TV backbone networks
- Outside plant
- FTTD (Desk)
- MDU FTTP cabling
- Data center installation
- Central office connector replacement
SPECIFICATIONS
| PARAMETERS | INSERTION LOSS | RETURN LOSS | OPERATING TEMPERATURE | |
| AVERAGE (DB) | MAXIMUM (DB) | |||
| SM UPC | 0.15 | 0.25 | ≤ -55 | -40 to +75°C |
| SM APC | 0.15 | 0.25 | ≤ -65 | -40 to +75°C |
| MM PC | 0.10 | 0.25 | ≤ -35 | -40 to +75°C |
ORDERING INFORMATION
| CONNECTOR TYPE | BOOT TYPE | AFL NO.*** | ||||
| UPC SM (Blue) | APC SM (Green) | PC 62.5 µm MM (Beige) | PC 50 µm MM (Black) | PC 50 µm LOMMF
(AQUA) **** |
||
| SC | 900 µm | FUSE-SC9SMU-6 | FUSE-SC9SMA-6 | FUSE-SC9M62-6 | FUSE-SC9M50-6 | FUSE-SC9M50L-6 |
| 3 mm | FUSE-SC3SMU-6 | FUSE-SC3SMA-6 | FUSE-SC3M62-6 | FUSE-SC3M50-6 | FUSE-SC3M50L-6 | |
| 4.8 mm | FUSE- SC48SMU-6 | FUSE- SC48SMA-6 | — | — | — | |
| LC | 900 µm | FUSE-LC9SMU-6 | FUSE-LC9SMA-6 | FUSE-LC9M62-6 | FUSE-LC9M50-6 | FUSE-LC9M50L-6 |
| 2 mm | FUSE-LC2SMU-6 | FUSE-LC2SMA-6 | FUSE-LC2M62-6 | FUSE-LC2M50-6 | FUSE-LC2M50L-6 | |
| FC | 900 µm | FUSE-FC9SMU-6 | FUSE-FC9SMA-6 | FUSE-FC9M62-6 | FUSE-FC9M50-6 | FUSE-FC9M50L-6 |
| 2 mm | FUSE-FC2SMU-6 | — | FUSE-FC2M62-6 | FUSE-FC2M50-6 | FUSE-FC2M50L-6 | |
| 3 mm | FUSE-FC3SMU-6 | — | FUSE-FC3M62-6 | FUSE-FC3M50-6 | FUSE-FC3M50L-6 | |
| ST | 900 µm | FUSE-ST9SMU-6 | — | FUSE-ST9M62-6 | FUSE-ST9M50-6 | FUSE-ST9M50L-6 |
| 2 mm | FUSE-ST2SMU-6 | — | FUSE-ST2M62-6 | FUSE-ST2M50-6 | FUSE-ST2M50L-6 | |
| 3 mm | FUSE-ST3SMU-6 | — | FUSE-ST3M62-6 | FUSE-ST3M50-6 | FUSE-ST3M50L-6 | |
- Boot kits are available for 2.0 mm/3.0 mm Simplex cordage
- Requires FAST APC Tool Kit for installation
- AFL NO. is for one pack of 6 pieces
- Laser Optimized Multi-Mode Fiber (LOMMF) compatible with OM3 and OM4 fibers
Fusion Spliced Field-Terminated Connectors
FUSEConnect® MPO Fusion Spliced Field-Terminated Connectors
- AFL’s FUSEConnect MPO performs as an equivalent to the standard factory-terminated MPO/MTP® assemblies. Designed to utilize standard ribbon, SpiderWeb Ribbon®, or loose tube cable, this connector helps minimize the complexity involved in the termination of a multi-fiber connection, allowing for a reliable and repeatable termination in field applications.
- This updated design for the FUSEConnect MPO replaces the mechanical clamp splice protector with a heat protection sleeve utilizing the on-board splicer heater eliminating the need for a separate mechanical clamp tool.
- The connector is designed for use with the new RT-02 ribbonizing tool which does not require ribbonizing glue resulting in a cleaner termination process.
FEATURES
- Field installable splice-on connector
- Heat sleeve style splice protector
- Utilizes RT-02 ribboning tool for glueless termination process
- Only six components
- No adhesives, crimping, or polishing
- Field MPO polarity customization
- Includes 3.0 mm round and flat ribbon boots in each pack
APPLICATIONS
- Connectorization in.
- RF-overlay FTTP networks
- Cable TV backbone networks
- Outside plant
- MDU FTTP cabling
- Connector restoration in the field
- Data center installation
- Patch cord customization in the field
SPECIFICATIONS
| PARAMETERS | INSERTION LOSS | RETURN LOSS | OPERATING TEMPERATURE | |
| AVERAGE (dB) | MAXIMUM (dB) | |||
| SM (OS1) | 0.25 | 0.75 | >65 dB | -40 to +75°C |
| SM (OS1), Low Loss | 0.10 | 0.35 | >65 dB | -40 to +75°C |
| 62.5/125 (OM1) | 0.10 | 0.35 | >30 dB | -40 to +75°C |
| 50/125 (OM4) | 0.10 | 0.35 | >30 dB | -40 to +75°C |
ORDERING INFORMATION
For cable size: 3.0 mm (ROUND) and 250 μm (FLAT)
| CONNECTOR TYPE
MALE/ FEMALE |
AFL NO.* | |||
| APC SM (GREEN) | APC LOW-LOSS SM (MUSTARD) | PC 62.5 µm MM (BEIGE) | PC 50 µm LOMMF (AQUA) ** | |
| Male | FUSEMPO-S-SMA-3-M-6 | FUSEMPO-S-LSMA-3-M-6 | FUSEMPO-S-MM6-3-M-6 | FUSEMPO-S-OM4-3-M-6 |
| Female | FUSEMPO-S-SMA-3-F-6 | FUSEMPO-S-LSMA-3-F-6 | FUSEMPO-S-MM6-3-F-6 | FUSEMPO-S-OM4-3-F-6 |
- AFL NO. is for one pack of 6 pieces
- Laser Optimized Multi-Mode Fiber (LOMMF) compatible with OM3 and OM4 fibers
RT-02 Ribbonizing Tool Ordering Information
| AFL NO. | DESCRIPTION |
| S017465 | RT-02 (tool only) |
| S017464 | FH-70-12PC (pair of pitch conversion holders for 200 µm loose fibers) |
| S017119 | FH-70-12 (pair – standard 12F ribbon holders) |
Product Information
FASTConnect Universal Tool Kit
- The FASTConnect Universal Tool Kit provides all of the necessary installation tools required for fiber preparation of 250 μm or 900 μm fibers, or 900 μm, 2 mm, or 3 mm cordage for AFL’s pre-polished FAST connectors.
- Included in the kit is the CT50 universal multimode/single-mode cleaver, AFL’s premier cleaver with 60,000 cleave blade life, automatic blade rotation, and Bluetooth® capability.
- The carrying case contains all the industry standard termination tools required for fiber preparation, as well as, adequate storage for carrying extra FAST connectors for on-site convenience.
FEATURES
- Industry-standard fiber preparation tools
- Compact design, flexible yet rugged case
- Complete instructions provided
APPLICATIONS
- Premise environments
- LAN Fiber to the Desk environments
- Patch panel/wiring closets
- FTTx applications
- Quick repair/replacement areas
ORDERING INFORMATION
| DESCRIPTION | AFL NO. |
| FASTConnect Boot Kits for 2.0 mm and 3.0 mm Cordage | |
| 2.0 mm Boot Kit, SC/LC/ST – Pack of 6 | FAST-BOOT-2MM-6 |
| 2.0 mm Boot Kit, SC/LC/ST – Pack of 100 | FAST-BOOT-2MM-100 |
| 3.0 mm Boot Kit, SC/LC/ST – Pack of 6 | FAST-BOOT-3MM-6 |
| 3.0 mm Boot Kit, SC/LC/ST – Pack of 100 | FAST-BOOT-3MM-100 |
| FASTConnect® Installation Kits | |
| FASTConnect High Precision Tool Kit with CT50 Cleaver | CS001201 |
| FASTConnect High Precision Tool Kit without cleaver | CS001201-NC |
| FASTConnect High Precision Tool Kit with CT16 Cleaver | CS010975 |
FUSEConnect Tool Kit and Accessories
- The FUSEConnect tool kit provides all the necessary installation tools required for fiber preparation of 900 μm fiber, 2 mm or 3 mm cordage for AFL’s FUSEConnect Fusion Spliced Field Installable Connectors except for a fusion splicer and precision cleaver.
- Included in the kit are standard fiber preparation tools and cleaning supplies as well as a FUSEConnect accessory kit and cord splitter tool, which can be bought separately from the tool kit.
- The cord splitter tool is uniquely designed to open the cordage of 2 mm and 3 mm cable allowing the termination of the ST and FC type connectors on simplex cordage.
FEATURES
- Industry-standard fiber preparation tools
- Compact design, flexible yet rugged case
- Complete instructions provided
APPLICATIONS
- Premise environments
- LAN Fiber-to-the-Desk environments
- Patch panel/wiring closets
- FTTx applications
- Quick repair/replacement areas
ORDERING INFORMATION
| DESCRIPTION | AFL NO. |
| FUSEConnect Installation Kits | |
| FUSEConnect Accessory Kit | FUSE-AC-KT |
| FUSEConnect Tool Kit | FUSE-TL-KT |
| FUSEConnect MPO Tool Kit | FUSE MPO-TL-KT |
| RT-02 Ribbonizing Tool | FUSE-R2-TL |
| Cord Splitter Tool | FUSE-ST-TL |
| FUSEConnect MPO Heater Attachment Tool | FUSE-HT-TL |
| MPO Boot Kit for Jacketed Ribbon (Pack of 6) | FUSEMPO-BOOT-JK-6 |
Fiber Cleavers
- Designed for FTTH or other space-constrained applications where ergonomics and durability are key, the CT16 fiber cleaver is compact and can be operated ambidextrously.
- It features a unique fiber adapter, allowing users to cleave two bare fibers simultaneously when paired with the dual fiber stripper, the SS-05.
- The CT50 features automated blade rotation, unprecedented durability, and simplistic maintenance unseen with any other cleaver.
- Paired with a Bluetooth®-enabled Fujikura splicer, cleaver blade positions can be automatically advanced when needed based on cleave count or cleave quality.
CT16 FEATURES
- Dual fiber adapter plate for single or two fiber cleaving
- Ambidextrous operation available
- Field replaceable fiber clamp pads and cleaver blade
- Shock resistant for drops up to 30″ in any of six different orientations
- Compact form factor and tool-less blade rotations
CT50 FEATURES
- Motorized blade rotation
- Bluetooth communication
- Shock resistant
- Simple one-step operation
- 60,000 cleave blade life
- Field serviceable
ORDERING INFORMATION
| DESCRIPTION | AFL NO. |
| CT16 | |
| CT16 Fiber Cleaver includes: FDB-06 scrap collector, AD-16A fiber adapter, HEX-01 hex wrench (1.5 mm), M-CT16-E instruction manual, CC-46 carrying case |
S018330 |
| CT50 | |
| CT50 Fiber Cleaver includes: AD-50 Adapter Plate, CC-37 Carrying Case and Instruction Manual | S017030 |
- For more information about AFL’s Connector Solutions, Fusion Splicers, Test Equipment, Fiber Management Systems, Closures, and accessories contact us at 800-235-3423 or online at www.AFLglobal.com.
- FUSION SPLICING EQUIPMENT
- TEST, INSPECT, CLEANING EQUIPMENT
- APEX® SEALED SPLICE CLOSURES
- ASCEND® HIGH-DENSITY PLATFORM
- www.AFLglobal.com or 8002353423
- LC-01012 Rev. 11, 12.4.2023
- © 2007, AFL, all rights reserved. Specifications are subject to change without notice.
- CONNECTOR SOLUTIONS
- FASTConnect® | FUSEConnect® | FUSEConnect® MPO
Documents / Resources
 |
AFL FAST-SC-SM-6 Connect Single Mode [pdf] Owner's Manual FAST-SC-SM-6, FAST-SC-SMAU-6, FAST-ST-SM-6, FAST-ST-SM-100, FAST-LC-SM-6, FAST-LC-SM-100, FAST-SC-SM-6 Connect Single Mode, FAST-SC-SM-6, Connect Single Mode, Single Mode, Mode |
