DDR4 lessenaar geheue
“
Produk inligting
Spesifikasies:
- Memory Type: DDR4 Desktop Memory (Unbuffered)
- Available Capacities: 16GB (Single Module)
- Available Frequencies: 3200MHz, 3600MHz
- Voltage: 1.2V
- Penkonfigurasie: 288-pen
- Error Correction: Non-ECC Unbuffered
- Registered: Yes
- CAS Latency: CL21 (depending on frequency)
- Form Factor: DIMM (Dual In-line Memory Module)
- Heat Spreader: Aluminum heat spreader
Verenigbaarheid:
Compatible with desktop motherboards with DDR4 slots.
Aanbevole komponente:
Compatible with Intel 600, 500, and 400 series chipsets and AMD
500 and 400 series chipsets. Also works with older chipsets that
support DDR4 memory.
Recommended Processors: Intel Core i3, i5, i7, i9 processors
(10th to 13th Gen) and AMD Ryzen 3, 5, 7, 9 processors (3000 to
5000 series).
Produkgebruiksinstruksies
Geheue konfigurasie:
- Install memory in pairs for dual-channel operation.
- Use identical memory modules with the same capacity and
frequency for best results. - Enable XMP/D.O.C.P. in BIOS to achieve advertised speeds.
Installasiegids:
- Power Down the System: Skakel die rekenaar af
completely and disconnect all power cables from the power
verskaf. - Open the Computer Case: Verwyder die sypaneel
of your computer case to access the motherboard. - Locate Memory Slots: Identify the memory slots
on your motherboard. Consult your motherboard manual for optimal
slot population order. - Release Retention Clips: Open the retention
clips at both ends of the memory slot by pushing them outward. - Align the Memory Module: Align the notch in
the memory module with the key in the memory slot for proper
oriëntasie. - Install the Memory: Firmly press down on the
memory module until the retention clips snap into place
outomaties. - Repeat for Additional Modules: As jy installeer
multiple modules, repeat the process for each module following the
motherboard’s recommended sequence. - Close the System: Replace the computer case
panel, reconnect all cables, and power on the system.
Let wel: After installation, enter the system
BIOS/UEFI to verify memory detection and enable XMP/D.O.C.P. for
advertised speed.
Gereelde Vrae (Gereelde Vrae)
Q: What should I do if my system does not boot after installing
KLLISRE Desktop DDR4 Memory?
A: Ensure that the modules are correctly seated in the memory
slots. Try reseating the modules or testing them one at a time to
identify any faulty module. Check compatibility with your
motherboard and ensure BIOS settings are configured correctly.
Q: Can I mix different capacities or frequencies of KLLISRE
Desktop DDR4 Memory modules?
A: While it is possible, it is recommended to use identical
modules for optimal performance. Mixing capacities or frequencies
may result in compatibility issues or reduced performance.
"`
KLLISRE Desktop DDR4 Memory
Gebruikershandleiding en installasiegids aflaai as Word-dokument
Produk verbyview
KLLISRE Desktop DDR4 Memory modules are designed for high-performance computing, offering excellent speed and reliability for gaming, content creation, and everyday computing tasks. These modules feature sleek heat spreaders for improved thermal performance and stability.
Spesifikasies
Specification Memory Type Available Capacities Available Frequencies Voltage Pin Configuration Error Correction Registered CAS Latency Form Factor Heat Spreader
Details DDR4 Desktop Memory (Unbuffered) 16GB (Single Module) 3200MHz, 3600MHz 1.2V 288-pin Non-ECC Unbuffered CL21 (depending on frequency) DIMM (Dual In-line Memory Module) Yes, aluminum heat spreader
Verenigbaarheid
Desktop motherboards with DDR4 slots
Versoenbare komponente
Aanbevole moederborde
KLLISRE Desktop DDR4 Memory is compatible with a wide range of desktop motherboards:
Intel 600, 500, and 400 series chipsets (Z690, B660, H610, Z590, B560, etc.)
AMD 500 and 400 series chipsets (X570, B550, X470, B450, etc.) Older chipsets that support DDR4 memory
Recommended Processors
This memory works with both Intel and AMD platforms:
Intel Core i3, i5, i7, i9 processors (10th, 11th, 12th, 13th Gen)
AMD Ryzen 3, 5, 7, 9 processors (3000, 4000, 5000 series)
Geheue konfigurasie
Vir optimale prestasie:
Install memory in pairs for dual-channel operation (check motherboard manual for correct slots)
For best results, use identical memory modules with same capacity and frequency
Enable XMP/D.O.C.P. in BIOS to achieve advertised speeds
Note: Higher frequency memory (3600MHz) may require a more recent CPU and motherboard to achieve full speed. Always check your motherboard’s QVL (Qualified Vendor List) for compatibility.
Installasiegids
Warning: Always handle memory modules by the edges. Avoid touching the gold contacts or components on the circuit board. Static electricity can damage the memory, so use an anti-static wrist strap when handling components. 1 Power Down the System Shut down the computer completely and disconnect all power cables from the power supply.
2 Open the Computer Case Remove the side panel of your computer case to access the motherboard.
3 Locate Memory Slots Identify the memory slots on your motherboard. Consult your motherboard manual for optimal slot population order (usually slots 2 and 4 for dual channel).
4 Release Retention Clips Open the retention clips at both ends of the memory slot by pushing them outward.
5 Align the Memory Module Align the notch in the memory module with the key in the memory slot to ensure proper orientation.
6 Install the Memory Firmly press down on the memory module until the retention clips snap into place automatically.
7 Repeat for Additional Modules If installing multiple modules, repeat the process for each module, following the motherboard’s recommended population sequence.
8 Close the System Replace the computer case panel, reconnect all cables, and power on the system.
Note: After installing new memory, enter the system BIOS/UEFI to verify that all memory is detected and enable XMP/D.O.C.P. to achieve the advertised speed.
Probleemoplossing
System Won’t Boot After Installation
Possible causes: Improperly seated memory, incompatible memory, BIOS needs update.
Solutions: Reseat memory modules, clear CMOS, update motherboard BIOS to latest version.
Only Partial Memory Detected
Possible causes: Improperly seated memory, incompatible memory population, faulty memory slot.
Solutions: Reseat memory modules, consult motherboard manual for proper population order, try modules in different slots.
Memory Not Running at Advertised Speed (3200/3600MHz)
Why this happens: By default, DDR4 memory runs at a conservative JEDEC standard speed (usually 2133MHz or 2400MHz). To achieve the advertised higher speeds, you must enable the XMP (Extreme Memory Profile) for Intel systems or D.O.C.P. (Direct Overclock Profile) for AMD systems in the BIOS.
Other reasons: Some older CPUs or motherboards may not support higher memory speeds. The memory controller in your CPU has limitations, and motherboard topology can affect maximum achievable speed.
Oplossings:
1. Enter BIOS/UEFI settings during boot (usually by pressing DEL or F2)
2. Find memory settings (often under “Advanced” or “Overclocking” menu)
3. Enable XMP (Intel) or D.O.C.P. (AMD)
4. Select the appropriate profile for your memory speed
5. Save changes and exit BIOS
6. If system becomes unstable, update BIOS to latest version
7. If problems persist, you may need to manually set speed and timings
System Instability or Crashes
Possible causes: Incompatible memory timing settings, overheating, insufficient power.
Solutions: Load BIOS optimized defaults, ensure proper system cooling, verify power supply adequacy, test with one module at a time.
Blue Screen Errors
Possible causes: Memory compatibility issues,Processor incompatibility, incorrect timings.
Solutions: Test each module individually, run memory diagnostic tools (Windows Memory Diagnostic or MemTest86), adjust BIOS memory settings.
Note: If problems persist, test each memory module individually to identify potential faulty modules. Contact KLLISRE support if you suspect a defective product.
Waarborg inligting
KLLISRE Desktop DDR4 Memory modules are covered by one year warranty. The warranty covers defects in materials and workmanship under normal use. Proof of purchase is required for warranty service.
For warranty claims or technical support, please contact KLLISRE support with your purchase details and a description of the issue.
This warranty does not cover damage resulting from accident, misuse, abuse, improper installation, or unauthorized modifications.
2023 KLLISRE. All rights reserved. KLLISRE is a registered trademark. Specifications are subject to change without notice.
Dokumente / Hulpbronne
 |
KLLISRE DDR4 Desktop Memory [pdfGebruikershandleiding 16GB 3200MHz, 16GB 3600MHz, DDR4 Desktop Memory, DDR4, Desktop Memory, Memory |