Introduction
Thank you for purchasing the DX Trigger Magnum and DX Skeleton Magnum action figure models. These models are designed for collectors and enthusiasts, featuring synchronized background music (BGM) and interactive elements. Please read this manual carefully before use to ensure proper handling and enjoyment of your product.
Warning: CHOKING HAZARD - Small parts. Not for children under 3 years.
Package Contents
Your package should contain the following items:
- 1 x DX Trigger Magnum Action Figure Model (Blue)
- 1 x Trigger Memory Unit
- 1 x DX Skeleton Magnum Action Figure Model (Black)
- 1 x Skull Memory Unit (also referred to as Fang Memory)
- Instruction Manual (this document)
Image: The set includes two action figure models: the blue DX Trigger Magnum with its 'Trigger' memory, and the black DX Skull Magnum with its 'Skull' memory. Both come in their original packaging.
Setup and Battery Installation
These models are battery-operated and require batteries for full functionality (batteries not included).
- **Unboxing**: Carefully remove the DX Trigger Magnum and DX Skeleton Magnum models and their respective Memory units from their packaging.
- **Battery Compartment**: Locate the battery compartment on each model. This is typically on the handle or underside of the main body.
- **Install Batteries**: Open the battery compartment cover. Insert the required batteries (e.g., AAA or AA, refer to the compartment markings for exact type and polarity). Close the battery compartment cover securely.
- **Insert Memory Unit**: Each model uses a specific Memory unit. For the DX Trigger Magnum, insert the 'Trigger' Memory unit into the designated slot. For the DX Skeleton Magnum, insert the 'Skull' (or 'Fang') Memory unit into its slot. Ensure it clicks into place.
Image: Close-up of the blue DX Trigger Magnum, showing its design and the 'Trigger' memory unit.
Image: Close-up of the black DX Skull Magnum, highlighting its design and the 'Skull' memory unit.
Operating Instructions
Once batteries are installed and the Memory unit is inserted, you can begin to operate your action figure models:
- **Power On**: Some models may have a small power switch. Ensure it is in the 'ON' position.
- **Activate BGM/Sound Effects**: With the Memory unit inserted, the model should recognize it. Press the designated button (often near the trigger or on the side of the model) to activate background music (BGM) and sound effects.
- **Trigger Function**: Pull the trigger to activate specific sound effects or light patterns associated with the model.
- **Memory Unit Interaction**: The Memory units are designed to synchronize with the models, providing unique sounds and BGM. The DX Trigger Magnum features 6 BGM tracks, while the DX Skull Magnum features 4 BGM tracks.
Image: The DX Trigger Magnum packaging, noting the inclusion of 6 background music (BGM) tracks.
Image: The DX Skull Magnum packaging, noting the inclusion of 4 background music (BGM) tracks.
Maintenance
- **Cleaning**: Wipe the models with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
- **Storage**: Store the models in a cool, dry place away from direct sunlight and extreme temperatures. Keep them away from dust and moisture.
- **Battery Care**: If the models will not be used for an extended period, remove the batteries to prevent leakage and damage. Dispose of used batteries responsibly according to local regulations.
- **Handling**: Handle the models with care to avoid dropping or impacting them, which could cause damage to the electronic components or plastic parts.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power/No sound | Batteries are dead or incorrectly installed. Power switch is off. | Check battery polarity and replace with fresh batteries. Ensure the power switch is in the 'ON' position. |
| Memory unit not recognized | Memory unit not fully inserted. Incorrect Memory unit for the model. | Ensure the Memory unit is fully inserted until it clicks. Verify you are using the correct Memory unit (Trigger for DX Trigger Magnum, Skull/Fang for DX Skeleton Magnum). |
| Sound/BGM is distorted or cuts out | Low battery power. Internal component issue. | Replace batteries with fresh ones. If the problem persists, contact customer support. |
Specifications
| Feature | Detail |
|---|---|
| Brand Name | Bandai |
| Model Numbers | DX Trigger Magnum, DX Skull |
| Item Type | Model, Action Figure |
| Material | Plastic |
| Scale | 1/100 |
| Dimensions | 1/1 (Specific to product design) |
| Mfg Series Number | Battery Operated |
| Completion Degree | Finished Goods |
| Version Type | First Edition |
| Remote Control | No |
| By Animation Source | Japan |
| Theme | Movie & TV |
| Gender | BOYS |
| Recommend Age | 14+y, 18+ |
| Origin | Mainland China |
| Certification | CE |
User Tips
- Always ensure the correct Memory unit is inserted for the corresponding Magnum model to activate the intended sounds and BGM.
- When replacing batteries, use high-quality alkaline batteries for optimal performance and longer play time.
- Keep the models and Memory units away from strong magnetic fields, as this may interfere with their electronic functions.
- For display purposes, consider using a stand to prevent accidental falls and damage.
Warranty and Support
For any issues, questions, or support regarding your DX Trigger Magnum or DX Skeleton Magnum models, please contact the seller directly. Please retain your proof of purchase for any warranty claims or support inquiries.
The product is eligible for free returns within 90 days of receipt, subject to the seller's return policy.
