M5STACK單元 C6L智慧邊緣運算單元使用手冊
Unit C6L is an intelligent edge computing unit integrated with the M5Stack_Lora_C6module — featuring an Espressif ESP32-C6 SoC and Semtech SX1262 LoRa transceiver — and engineered with a modular design for long-range, low-power LoRaWAN communication alongside high-speed 2.4 GHz Wi-Fi and BLE connectivity.
It includes a 0.66″ SPI OLED display for real-time data visualization, a WS2812Caddressable RGB LED for system-status indication, a built-in buzzer for audible alerts, and front-panel buttons (SYS_SW) with a reset switch for local interaction. Astandard Grove I²C interface allows seamless integration with M5Stack hosts and various Grove sensors. The onboard USB Type-C port supports ESP32- C6 firmware programming, serial debugging, and 5 V power input, while automatic power switching and multi-channel ESD/surge protection ensure stable operation. Unit C6L excels at real-time data acquisition, edge-intelligence processing, and remote control, making it ideal for IoT applications such as smart agriculture, environmental monitoring, industrial IoT, smart buildings, asset tracking, and urban infrastructure sensing.\
1.1. C6L單元
- 通訊能力
Integrated LoRa (Semtech SX1262), supporting LoRaWAN Class A/B/Candpointto-point modes 2.4 GHz Wi-Fi and BLE via ESP32-C6-MINI-1U - 處理器和效能
Main Controller: Espressif ESP32-C6 (single-core RISC-V, up to 40 MHz) On-chip Memory: 512 KB SRAM with integrated ROM - 電力與能源管理
Power Input: USB Type-C (5 V input) and Grove 5 V input - 顯示和指示器
0.66″ SPI OLED display for real-time data visualization and status monitoringWS2812C addressable RGB LED for system-status indication Built-in buzzer for audible alerts - Interfaces & Controls
Grove I²C interface (with 5 V power) for seamless connection to M5Stack hostsandGrove sensors USB Type-C port for firmware programming, serial debugging, and power input Front-panel buttons (SYS_SW) and reset switch (MCU_RST) for local control - Expansion & Debug Pads
Bootloader pad: predefined jumper pad for entering bootloader mode Test points (TP1–TP8) for signal probing and in-circuit debug
2. 規格
| 範圍 | 規格 |
| 單晶片 | Espressif ESP32-C6（單核心 RISC-V，最高 40 MHz） |
| 溝通 | LoRaWAN; 2.4 GHz Wi-Fi BLE |
| 電源輸入 | USB Type-C(5V)和Grove 5V |
| 供應量tage | 3.3 V（板載 LDO） |
| 快閃記憶體 | 16 MB SPI快閃記憶體（128 Mbit） |
| 展示 | 0.66”SPI OLED(128×64) |
| 指標 | WS2812C可尋址RGB LED |
| 蜂鳴器 | 板載蜂鳴器 |
| 按鈕 | System button (SYS_SW)and reset button(MCU_RST) |
| 介面 | Grove I²C；USB Type-C；引導程式板；TP1-TP8 偵錯板 |
| 天線 | 2×SSMB-JEF clamp 連接器；2×IPEX-4天線連接器 |
| 工作溫度 | 工作溫度 |
| 附加功能 | Multi-channel ESD/surge protection |
| 製造商 | M5Stack Technology Co., Ltd Block A10, Expo Bay South Coast, Fuhai Street, Bao’an District, Shenzhen, China |
| CE 頻率範圍 | 2.4G Wi-Fi: 2412-2472MHz BLE: 2402-2480MHz Lora: 868-868.6MHz |
| CE 的最大 EIRP | BLE: 5.03dBm 2.4G Wi-Fi: 16.96dBm Lora: 9.45dBm |
| 接收器類別 | The equipment provider declared that the receiver category for the EUTis2. |
3. FCC 警告
美國聯邦通訊委員會警告：
未經合規負責方明確批准的任何變更或修改都可能導致使用者操作設備的權限失效。本設備符合 FCC 規則第 15 部分的規定。操作須符合以下兩個條件：(1) 該設備不會造成有害幹擾，且 (2) 該設備必須接受收到的任何干擾，包括可能導致意外操作的干擾。
重要提示：
筆記: This equipment has been tested and found to comply with the limits for a ClassBdigital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
通過以下一項或多項措施糾正干擾：
- 重新調整接收天線的方向或位置。
- Increase the separation betweentheequipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator&your body.
I. Installing Arduino IDE(https://www.arduino.cc/en/Main/Software)
點擊訪問Arduino官方 web站點，然後選擇您的安裝包
operating system to download. Ⅱ. Installing Arduino Board Management
1. 董事會經理 URL is used to index the development board information for specific platform. In the Arduino IDE menu, select File -> 偏好
2.複製ESP板管理 URL 下面進入附加董事會經理
URLs: field, and save.
https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
3. 在側邊欄中，選擇 Board Manager，搜尋 ESP，然後按一下安裝。
4. In the sidebar, select Board Manager, search for M5Stack, and click Install.
Depending on the product used, select the corresponding development board under
Tools -> Board -> M5Stack -> {ESP32C6 DEV Module board}.
5.用數據線將設備與電腦連接，上傳程序
文件/資源
 |
M5STACK單元 C6L智慧邊緣運算單元 [pdf] 使用者手冊 M5UNITC6L, 2AN3WM5UNITC6L, Unit C6L 智慧邊緣運算單元, Unit C6L, 智慧邊緣運算單元, 邊緣運算單元, 運算單元, 單元 |