M5STACK யூனிட் C6L இன்டெலிஜென்ட் எட்ஜ் கம்ப்யூட்டிங் யூனிட் உரிமையாளர் கையேடு
டோமஸ் லைன் ஈஏசி டிஸ்க் டிரைவர் டி மோஷன் கண்ட்ரோல் டிஸ்க் பயனர் கையேடு

1. அவுட்லைன்

Unit C6L is an intelligent edge computing unit integrated with the M5Stack_Lora_C6module — featuring an Espressif ESP32-C6 SoC and Semtech SX1262 LoRa transceiver — and engineered with a modular design for long-range, low-power LoRaWAN communication alongside high-speed 2.4 GHz Wi-Fi and BLE connectivity.
It includes a 0.66″ SPI OLED display for real-time data visualization, a WS2812Caddressable RGB LED for system-status indication, a built-in buzzer for audible alerts, and front-panel buttons (SYS_SW) with a reset switch for local interaction. Astandard Grove I²C interface allows seamless integration with M5Stack hosts and various Grove sensors. The onboard USB Type-C port supports ESP32- C6 firmware programming, serial debugging, and 5 V power input, while automatic power switching and multi-channel ESD/surge protection ensure stable operation. Unit C6L excels at real-time data acquisition, edge-intelligence processing, and remote control, making it ideal for IoT applications such as smart agriculture, environmental monitoring, industrial IoT, smart buildings, asset tracking, and urban infrastructure sensing.\

1.1. அலகு C6L

  1. தொடர்பு திறன்கள்
    Integrated LoRa (Semtech SX1262), supporting LoRaWAN Class A/B/Candpointto-point modes 2.4 GHz Wi-Fi and BLE via ESP32-C6-MINI-1U
  2. செயலி & செயல்திறன்
    Main Controller: Espressif ESP32-C6 (single-core RISC-V, up to 40 MHz) On-chip Memory: 512 KB SRAM with integrated ROM
  3. மின்சாரம் & ஆற்றல் மேலாண்மை
    Power Input: USB Type-C (5 V input) and Grove 5 V input
  4. காட்சி & குறிகாட்டிகள்
    0.66″ SPI OLED display for real-time data visualization and status monitoringWS2812C addressable RGB LED for system-status indication Built-in buzzer for audible alerts
  5. Interfaces & Controls
    Grove I²C interface (with 5 V power) for seamless connection to M5Stack hostsandGrove sensors USB Type-C port for firmware programming, serial debugging, and power input Front-panel buttons (SYS_SW) and reset switch (MCU_RST) for local control
  6. Expansion & Debug Pads
    Bootloader pad: predefined jumper pad for entering bootloader mode Test points (TP1–TP8) for signal probing and in-circuit debug

2. விவரக்குறிப்புகள்

அளவுரு விவரக்குறிப்பு
MCU எஸ்பிரெசிஃப் ESP32-C6(சிங்கிள்-கோர் RISC-V, 40 MHz வரை)
தொடர்பு LoRaWAN; 2.4 GHz Wi-Fi BLE
ஆற்றல் உள்ளீடு யூ.எஸ்.பி டைப்-சி(5வி) மற்றும் க்ரோவ் 5வி
வழங்கல் தொகுதிtage 3.3 V (ஆன்-போர்டு LDO)
ஃபிளாஷ் சேமிப்பு 16 எம்பி SPI ஃபிளாஷ் (128 மெ.பிட்)
காட்சி 0.66”SPI OLED(128×64)
காட்டி                                  WS2812C முகவரியிடக்கூடிய RGB LED
பஸர் விமானத்தில் உள்ள பஸர்
பொத்தான்கள் System button (SYS_SW)and reset button(MCU_RST)
இடைமுகங்கள் குரோவ் I²C;USB டைப்-C;பூட்லோடர் பேட்;TP1-TP8 டீபக் பேட்கள்
ஆண்டெனாக்கள் 2×SSMB-JEF clamp இணைப்பிகள்;2×IPEX-4 ஆண்டெனா இணைப்பிகள்
இயக்க வெப்பநிலை இயக்க வெப்பநிலை
கூடுதல் அம்சங்கள் Multi-channel ESD/surge protection
உற்பத்தியாளர் M5Stack Technology Co., Ltd Block A10, Expo Bay South Coast, Fuhai Street, Bao’an District, Shenzhen, China
CE க்கான அதிர்வெண் வரம்பு 2.4G Wi-Fi: 2412-2472MHz BLE: 2402-2480MHz Lora: 868-868.6MHz
CE-க்கான அதிகபட்ச EIRP BLE: 5.03dBm 2.4G Wi-Fi: 16.96dBm Lora: 9.45dBm
பெறுநர் வகை The equipment provider declared that the receiver category for the EUTis2.
2.1 தொகுதி அளவு
தொகுதி அளவு

3. FCC எச்சரிக்கை

FCC எச்சரிக்கை:
இணக்கத்திற்குப் பொறுப்பான தரப்பினரால் வெளிப்படையாக அங்கீகரிக்கப்படாத எந்த மாற்றங்களும் மாற்றங்களும் சாதனத்தை இயக்குவதற்கான பயனரின் அதிகாரத்தை ரத்து செய்யலாம். இந்த சாதனம் FCC விதிகளின் பகுதி 15 உடன் இணங்குகிறது. செயல்பாடு பின்வரும் இரண்டு நிபந்தனைகளுக்கு உட்பட்டது: (1) இந்தச் சாதனம் தீங்கு விளைவிக்கும் குறுக்கீட்டை ஏற்படுத்தாமல் இருக்கலாம், மேலும் (2) விரும்பத்தகாத செயல்பாட்டை ஏற்படுத்தக்கூடிய குறுக்கீடு உட்பட பெறப்பட்ட எந்தவொரு குறுக்கீட்டையும் இந்தச் சாதனம் ஏற்க வேண்டும்.
முக்கிய குறிப்பு:
குறிப்பு: This equipment has been tested and found to comply with the limits for a ClassBdigital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
பின்வரும் நடவடிக்கைகளில் ஒன்று அல்லது அதற்கு மேற்பட்டவற்றின் குறுக்கீட்டை சரிசெய்யவும்:

  • பெறும் ஆண்டெனாவை மாற்றியமைக்கவும் அல்லது இடமாற்றவும்.
  • Increase the separation betweentheequipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator&your body.
Arduino நிறுவல்

I. Installing Arduino IDE(https://www.arduino.cc/en/Main/Software)
Arduino அதிகாரியைப் பார்க்க கிளிக் செய்யவும் webதளம் , மற்றும் உங்களுக்கான நிறுவல் தொகுப்பைத் தேர்ந்தெடுக்கவும்
operating system to download. Ⅱ. Installing Arduino Board Management
1. வாரிய மேலாளர் URL is used to index the development board information for specific platform. In the Arduino IDE menu, select File -> விருப்பத்தேர்வுகள்
Arduino நிறுவல்

2. ESP பலகை நிர்வாகத்தை நகலெடுக்கவும் URL கூடுதல் வாரிய மேலாளருக்கு கீழே
URLs: field, and save.
https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
Arduino நிறுவல்
Arduino நிறுவல்

3. பக்கப்பட்டியில், Board Manager என்பதைத் தேர்ந்தெடுத்து, ESP ஐத் தேடி, நிறுவு என்பதைக் கிளிக் செய்யவும்.
Arduino நிறுவல்

4. பக்கப்பட்டியில், Board Manager என்பதைத் தேர்ந்தெடுத்து, M5Stack ஐத் தேடி, நிறுவு என்பதைக் கிளிக் செய்யவும்.
Depending on the product used, select the corresponding development board under
Tools -> Board -> M5Stack -> {ESP32C6 DEV Module board}.
Arduino நிறுவல்

5. நிரலைப் பதிவேற்ற, தரவு கேபிள் மூலம் சாதனத்தை உங்கள் கணினியுடன் இணைக்கவும்.

M5STACK Logo

ஆவணங்கள் / ஆதாரங்கள்

M5STACK யூனிட் C6L இன்டெலிஜென்ட் எட்ஜ் கம்ப்யூட்டிங் யூனிட் [pdf] உரிமையாளரின் கையேடு
M5UNITC6L, 2AN3WM5UNITC6L, அலகு C6L நுண்ணறிவு முனை கணினி அலகு, அலகு C6L, நுண்ணறிவு முனை கணினி அலகு, முனை கணினி அலகு, கணினி அலகு, அலகு

குறிப்புகள்

கருத்து தெரிவிக்கவும்

உங்கள் மின்னஞ்சல் முகவரி வெளியிடப்படாது. தேவையான புலங்கள் குறிக்கப்பட்டுள்ளன *