Yelaw CR1001 Alarm Clock with Time Projection

Yelaw CR1001 Alarm Clock with Time Projection

USER MANUAL

MODEL: CR1001

Chapter 1 LOCATION OF CONTROLS

 

 Alarm Clock

BUTTONS

1. TIME/12-24H & MEM/M+
2. HOUR&TU-
3. MIN &TU+
4. LCD DIMMER/DST
5. SNOOZE/OK /SLEEP
6. ALARM 1 & ALARM OFF
7. ALARM 2 &ALARM OFF
8. RADIO & RADIO OFF
9. PROJECTION ON/FLIP/OFF
10. VOLUME+
11. VOLUME-

INDICATORS

12. AM
13. PM

14. ALARM 1
15. RADIO ALARM
16. DST
17. RADIO
18. ALARM 2
19. RADIO ALARM

PARTS

20. FOCUS RING
21. BATTERY DOOR
22. USB JACK
23. DC JACK
24. ANTENNA
25. SPEAKER
26. HOLDER ( x 2pcs)

27. PROJECTION DIMMER

Chapter 2 POWERING ON

Insert the 2 included holders into the hole on the back to avoid being knocked over.
1. Install 2pcs 1.5V “AAA” batteries to the proper terminals in the battery compartment to memorize the time and alarm setting in case of power outage.

NOTE: Batteries(not included) don’t support time display but alarm will still go off in case of AC power fai I u re.

2. Connect the adapter line to DC jack, then plug into a 100-240V AC wall power outlet.

Chapter 3 TIME SETTING

Before time setting, check whether FM radio is closed, if not, press  BUTTON button to turn off radio.

1. Press  BUTTON button once, the display  BUTTON starts flashing.

2. Press  BUTTON button to set the hour, press  BUTTON button to set the minute.

3. Press BUTTON button to save time or wait for another 5 seconds to confirm automatically.

To change 12H/24H time format

Hold Press  BUTTON to change 12H/24H time formate

Chapter 4 ALARM SETTING

Indicator BUTTON means buzzer alarm. Indicator BUTTON means radio alarm.
Both indicators are off means alarms are inactive.

Set alarm wake by buzzer

1. Press once BUTTON button, buzzer alarm indicator BUTTON will light up, and the display starts flashing.
2. Press BUTTON button to set the HOUR, press BUTTON button to set the MINUTE, press BUTTON button or wait for 5 seconds to confirm the alarm time automatically.

Set alarm wake by FM radio

1. Double press BUTTON button, radio alarm indicator  BUTTON will light up, and display I 6 : DD I start flashing.

2. Press BUTTON button to set the HOUR, press BUTTON button to setthe MINUTE, press BUTTON button or wait for 5 seconds to confirm the alarm time automatically.

Set alarm volume

1. Press BUTTON or button to adjust alarm volume, the display will show the alarm volume and the speaker will play.

2. Press BUTTON button to save alarm setting or just wait for another 5 seconds to confirm automatically.
This product has a convenient dual alarm function. Each alarm function can be set independently, with a choice of radio alarm sound or buzzer alarm sound.

NOTE: The last radio channel you listened to will be the default radio alarm and Alarm 2 will be the same as Alarm 1.

Turn off Alarm

When alarm goes off:

1. Press BUTTON button to temporarily turn off alarm for 9 minutes.
Alarm will ring every next 9 minutes

2. Press l:!I button to turn off alarm for 24 hours.
The alarm indicator BUTTON or  BUTTONis still on, which means alarm is still active and will ring after 24 hours.

3. Cancel Alarm
Hold press BUTTON button until BUTTON or  BUTTON indicator disappear from the display, which means alarm is completely turned off.

Turn off Alarm 2 is the same as ALARM 1.

Chapter 5 DIMMER & DST

Repeat Leo BUTTON button to adjust the brightness of display for your preference. There are 5 dimmer levels.

Hold press Leo BUTTON button to switch DST function, hold press Leo BUTTON button again to turn off DST function.

 

Chapter 6 USB CHARGING

Device can charge both your phone or tablet PC at the same time.

The maximum charge current is 1 Ampere

Chapter 7 RADIO SETTING

Turn ON or OFF radio

Press  BUTTON button to turn on, press BUTTON button again to turn off.

Manual Tuning Radio Channel

Repeat BUTTONor BUTTON button to tune into the desired radio channel.
Each press BUTTONbutton, FM frequency will tune up by 0.1 MHZ.
Each press BUTTON button, FM frequency will tune down by 0.1 MHZ.

Auto Scanning Radio Channel

Hold press BUTTON or BUTTON button for more than 2 seconds to start auto scanning.
Scanning will stop automatically once received an available radio channel.

Adjust Radio Volume

Repeat BUTTON  button to increase the volume.
Repeat  vol- button to decrease the volume.

FM frequency: 87.5 MHZ – 108MHz, 87.5MHz preset as a default

Auto Preset Channel Store

After radio turns on, hold press BUTTON  button to start preset store, radio will store available channel to P01 …… P20. Then press the  BUTTON
button to confirm to store the channel.

Manual Preset Channel Store

When radio receives the channel which you desire, hold press  BUTTONbutton, display will show the preset position number, press  BUTTON or  button to select the preset position number which you desire then press BUTTON to confirm your selection.

Preset Channel Recall

After radio turns on, repeat press  BUTTONbutton to switch preset store channel, after you have selected the channel you desire, wait more than 3 seconds, radio will confirm you-r 0s5el- ection.

Chapter 8 SETTING TIMER SETTING

The SLEEP timer function allows the radio to play in blocks of 10, 20, 30, 40, 50, 60, 70, 80, or 90 minutes, then automatically turn off.

1. Turn on the radio

2. Press once  BUTTON , display show  button
3. Repeat BUTTON to select your desired sleep time. Sleep time show on the display in sequence as 60 > 70 > 80 > 90 > 80 ……. > 20 > 1 O > OFF
4. Wait for 2 seconds, radio will confirm your selection.

Chapter 9 PROJECTION MODE

1. Press Projection mode Button   button to turn on projection.

2. Press Button button once again to flip the projection time.
3. Press Button  once again to turn off projection.
4. Rotate focus ring Button to adjust clarity of projection image.

Note: 1. Best projection distance is from 1.5 to 3.0 meters (4.92 to 9.84 feet).

2. Projector is a common LED light, so the projector is not visible in bright environment.
3. If projection numbers are fuzzy, please rotate the focus ring (20) to adjust proper angle for clear projection image.

Chapter 10 PROJECTION DIMMER

Press Button button to adJ·ust the brightness of proJ· ection for your preference.

BUTTON

Documents / Resources

Yelaw CR1001 Alarm Clock with Time Projection [pdf] User Manual
2A6CL-CR1001, 2A6CLCR1001, cr1001, CR1001 Alarm Clock with Time Projection, CR1001, Alarm Clock with Time Projection, Clock with Time Projection, Time Projection, Projection, Clock

References

Leave a comment

Your email address will not be published. Required fields are marked *