Yale YLBL226-PROG Libi Digital Lever Keyed
NOTE
- Do not use any chemicals or add any lubricants when cleaning the lock, to avoid damaging the panel and coating.
- 9V Alkaline batteries are recommended to maintain stable and prolonged power.
Operational interface
- Light sensor
Proximity to wake up the interface. - Number buttons
Used to enter user codes.
Each code must be 4 to 10 digits in length. - Confirm button
For function setup. - Indicator light
Red and green light display. - Cancel button
Numbers entered incorrectly can be deleted. - Cylinder
To be locked and unlocked with the key. - Battery holder
Uses 9V Alkaline batteries. - Programming button
Restore default setting/Programming mode. - Slide
Switch passage mode.
Stays unlocked, allowing entry without a key or code. - Battery cover
Push it upward and outward to replace the batteries.
Operating instructions
Operation Indicator Sounds and Lights
| Meaning | Lights | Sounds |
| Successful Operation | Flashes Green Once | 1 Beep |
| Successful Programming | Flashes Green Twice | 2 Long Beeps |
| Default Setting Restored | Flashes Orange 3 Times | 3 Long Beeps |
| Operation Error | Flashes Red 3 Times | 3 Beeps |
| Programming Error | Flashes Red 5 Times | 5 Beeps |
| Code Input Error 5 times/ System Lockdown | Flashes Red 5 Times | 5 Long Beeps |
| Locked | Flashed Red Once | 1 Long Beep |
| Unlocked | Flashed Green Twice | 2 Beeps |
| Low Battery Power | Flashes Red 10 Times | 10 Long Beeps |
| In Programming Mode | Flashes Orange Slowly | None |
Programming
NOTE
- The programming button is located on the interior chassis below the battery holder.
- During programming, if no button is pressed within 5 seconds, the system will time out and you will need to restart the procedure.
- If a programming code is created, the programming button will only be used for restoring the lock to default settings.
The code must be used to start programming mode. - For new installations, or when a lock is restored to default settings, you must use the programming button to start the programming mode.
| Add User Code (UC) | Programming  1  enter UC Button
NOTE : Up to 70 User Codes can be saved. User Codes should be 4 to 10 digits in length. |
||
| Delete Individual User Codes (UC) | Programming Button
|
2 enter UC |
|
| Delete All User Codes (UC) | Programming Button | 3 |
|
| Add Programming Code (PC) | Programming 4 enter PC Button
NOTE :
|
||
| Set Auto-Lock Time Delay | Programming Button | 6 |
1-99 seconds |
| Toggle Mute On/Off (default Off) | Programming Button | 7 |
|
| Enable/Disable Vacation Mode | Programming 8 Button
NOTE : If enable vacation mode, all User Codes are still in the memory, but all invalid until disable vacation mode. |
||
| Add One-time User Code | Programming 9 enter Button one-time UC NOTE : Up to 5 One-time User Codes can be saved. One-time User Codes should be 4 to 10 digits in length. |
||
| Restore Default Setting
Press programming button for more than 5 seconds, and the programming is reset back to the original factory codes once you hear 3 long beeps. NOTE : After restoring default setting, all User Codes will be deleted and all programming will be changed to factory settings.
|
|||
Part of ASSA ABLOY
ASSA ABLOY New Zealand Limited, 6 Armstrong Rd, Albany Auckland 0632, New Zealand yalehome.com/nz ©2024
Approved 2024-06-27
Programming notes
Add User Code
- Up to 70 User Codes can be saved. User Codes should be 4 to 10 digits in length.
- For security reasons, the first 4 digits of each User Code must be unique.
- For example, you are unable to program a User Code 1-2-3-4-5 as well as a User Code 1-2-3-4-6.
- Press the lock button before entering your code to light up the keypad at night.
Delete All User Codes
- Keypad locking function will be disabled when User Codes are deleted. The lock can only be operated manually by key during this time.
Enable/Disable Programming Code
- Optional: A Programming Code enables you to make programming changes without needing to access the programming button.
- One Programming Code can be saved and should be 4 to 10 digits in length.
- The Programming Code can not be the same as any User Code and will not unlock the lock.
- To program the lock when the Programming Code is enabled, instead of pressing the programming button, enter the Programming Code and press the confirm button to enable the Programming Code.
- Repeat the programming steps to disable the Programming Code. Please note once a Programing Code is enabled, the programming button is disabled and can only be used to factory reset the lock.
Set Auto-Lock Time Delay
- Press the keypad number that corresponds to your time delay preference, choosing between 1 and 99 seconds.
Toggle Mute On/Off
- LED status indicator will still function once audio is disabled. Repeat the programming steps to enable the audio.
Enable/Disable Vacation Mode
- When vacation mode is enabled, all electronic functions will be disabled as well.
- The door must be locked or unlocked manually with the key.
- Repeat the programming steps to disable vacation mode.
Add One-Time Use Code
- Up to 5 One-time User Codes can be saved. One-time User Codes should be 4 to 10 digits in length.
- The One-Time User Code will be deleted automatically after it is used.
- The same One-Time User Code can be created again after it’s used.
Factory Reset
- After restoring default setting, all User Codes will be deleted and all programming will be changed to factory settings.
Slider functions – choosing a mode
Auto-lock mode
Key or code is needed for entry from the outside.
Default auto-lock is 5 seconds.
Passage mode
Stays unlocked, allowing entry without a key or code.
Trouble shooting
| Problem | Possible Cause | Corrective Action |
| After the installation is complete and the batteries are in place, none of the buttons are responsive. (No sound, and no backlight) |
Issues with batteries or the wiring. | Replace the batteries or make sure the batteries are installed correctly. Please check whether the cable from the interior lock unit is connected correctly. |
| The door cannot be locked. | The slider is located in the function : Passage | Manually switch the slider function position. |
| After installing the lockset and batteries, the door can’t be locked and three short beeps are emitted when you press any button. | The battery doesn’t have enough energy to supply for the lock. | Replace the battery.
|
ASSA ABLOY Australia Pty Limited, 235 Hunting dale Rd, Oakleigh, VIC 3166 1300 LOCK UP (1300 562 587) yalehome.com/au | ABN 90 086 451 907 ©2024
Documents / Resources
 |
Yale YLBL226-PROG Libi Digital Lever Keyed [pdf] User Guide YLBL226-PROG, YLBL226-PROG Libi Digital Lever Keyed, Libi Digital Lever Keyed, Digital Lever Keyed, Lever Keyed, Keyed |
