XTOOL S1 Laser Cutter Instruction Manual

Compliance: Directive RED 2014/53/EU, RoHS directive 2011/65/EU & (EU) 2015/863
Standards: American National Standard for Safe Use of Lasers (Z136.1-2022), IEC 60825-1:2014, EN 60825-1:2014/A11:2021

Product Usage Instructions

Safety Instructions

Read and understand all safety precautions before using the machine.

Ensure proper assembly and functionality of the machine.
Regularly inspect for damage before operation.

Maintain a clean and flat workspace.
Do not modify the machine without authorization.

Do not operate under direct sunlight.
The machine is not user-serviceable; contact authorized professionals for repairs.

Laser Safety

Ensure the laser module is enclosed during operation.

Do not operate the machine with removed parts.
Avoid engraving or cutting PVC or vinyl materials.

Do not work with unknown materials.
Keep the lid closed during laser operation.

Fire Safety

Avoid leaving the device unattended during operation.

Keep combustible materials away from the machine.
Use equipment in areas without children present.

Frequently Asked Questions

Q: Can I modify the machine’s structure?

A: No, do not change the machine’s structure without authorization to ensure safety and proper functionality.

Q: What materials should I avoid engraving or cutting?

A: Avoid engraving or cutting materials containing PVC, vinyl, or unknown substances to prevent harmful effects on the machine and human health.

Q: What should I do if I suspect damage to the machine?

A: Do not operate the machine if damage is suspected. Contact authorized professionals for inspection and repairs.

INTRODUCTION

Statement

Thank you for choosing xTool products!

If you use the product for the ﬁrst time, read carefully all the accompanying materials of the product to improve your experience with it.
If you do not use the product according to the instructions and requirements of the Manual, or mis-operate the product due to misunderstanding, etc., the Company shall bear no responsibility for any loss resulting therefrom.
The Company has collated the content of the Manual rigorously and carefully, but errors or omissions may remain.
The Company is committed to continuously improving product functions and service quality and therefore reserves the right to change any product or software described in the Manual and the content of the Manual at any time.
The Manual is intended to help you use the product properly and does not include any description of hardware and software conﬁguration.
For product conﬁguration, refer to the related contract (if any) and packing list, or consult your distributor.
Images in the Manual are for reference only and the actual product may vary.
Protected by copyright laws and regulations, the Manual shall not be reproduced or transcribed in any way, be transmitted on any wired or wireless network in any manner, or be translated into any language, or be modiﬁed in any way, such as content, image, or layout modiﬁcation, without the prior written authorization of the Company.
The Company is committed to continuously improving the product and related materials. The product and the Manual are subject to change, and updates can be found at xtool.com.

Declaration of conformity

Hereby, Makeblock Co., Ltd., declares that this product complies with the essential requirements and other relevant provisions of Directive RED 2014/53/EU and the RoHS directive 2011/65/EU & (EU) 2015/863.

FCC statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference,
this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC radiation exposure statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
Maximum RF transmit power: Wi-Fi 2.4G (2412–2472 MHz) < 20 dBm

Safety ﬁrst

(important)

General safety
- Read and get familiar with all safety precautions and procedures before using the machine. Strictly follow all safety precautions. Ensure that the machine is properly assembled and is working properly.
- Caution Follow the operating principles
- Check the machine for damage every time before you use it. Do not operate it in any way when any damage or defect is found.
- Ensure that the workspace is clean and ﬂat.
- Do not disassemble the machine or change its structure in any way without authorization. Do not modify or decompile its operating system.
- Do not leave the device unattended during operation. Pay attention to whether it is working properly.
- Keep the inside of the machine clean. Residues and chippings accumulated during cutting and engraving are dangerous and may cause a ﬁre. Clean the chippings and residues inside the work area regularly.
- The machine works properly at the temperature of 0°C to +35°C and can be stored properly at the temperature of –10°C to +40°C. Do not operate it at a temperature lower than 0°C.
- Do not place or use your machine under direct sunlight.
- This product is not user-serviceable. It must be returned to the factory or repaired by authorized professionals.

Laser safety
- Generally, the laser module is completely enclosed in the casing and light shield during operation. The device has a safety interlock switch. If the lid is lifted during operation, the device will stop working.
- Warning Follow the safety precautions:
- Do not operate the machine when any part of it is removed. Removing any part may expose the laser system and cause damage to the machine.
- Do not engrave or cut any material that contains PVC or vinyl (processing plastics is not recommended). These materials (and other materials containing chlorine/chloride) can generate corrosive vapor that is extremely harmful to the human body and can cause damage to the device. Any damage caused by engraving or cutting any material containing PVC or vinyl is not covered by the Company’s warranty.
- Do not engrave or cut any unknown materials. Vaporization or melting of many materials, which include but are not limited to PVC and polycarbonate, may release harmful smoke.
- Laser operation is prohibited when the lid is lifted. Make sure that the lid is closed during operation and do not tamper with the safety mechanism of the lid.
- Do not leave the device unattended during operation. Pay attention to whether it is working properly.
- The reference standards for laser safety are the American National Standard for Safe Use of Lasers (Z136.1-2022), International Electrotechnical Commission Standard (IEC 60825-1:2014), and European Standards (EN 60825-1:2014/A11:2021).

Fire safety
- A high-density laser beam is used by the device to irradiate the material to be cut or engraved, to heat the material surface, and vaporize the material without burning.
- But most materials are inherently ﬂammable and may be ignited to form an open ﬂame that can burn down the device (even if it is made of ﬂame-retardant materials) and its surroundings.
- Experience shows that vector cutting with a laser is most likely to produce an open ﬂame. In particular, acrylic has proven to be extremely ﬂammable in vector cutting.
- Danger Read the following warnings and suggestions carefully:
- Equipment for use in locations where children are not likely to be present.
- Ensure that the workspace is well-ventilated so that the generated smoke can be discharged in time.
- Do not stack materials (especially organic ones, such as paper) around the machine. They may cause the spread of ﬂames and increase the risk of material ignition.
- Do not leave the machine unattended when it is working. If the machine works with setting errors and is left unattended for a long time, or if a mechanical or electrical fault occurs, a ﬁre may be caused.
- Clean the device regularly. Excessive accumulation of residues and chippings from cutting and engraving would increase the risk of ﬁre.
- The internal working area needs to be cleaned periodically to ensure that there is no residue or chipping inside the device.
- Ensure that the area around the machine is clean without any cluttered ﬂammable materials, explosives, or volatile solvents, such as acetone, alcohol, or gasoline.
- Keep a ﬁre extinguisher and perform regular maintenance and inspection of it.
- If a ﬁre occurs during processing, take good care of yourself. For a small ﬂame, you can wait for it to go off; for a larger ﬁre, please keep a safe distance and use a ﬁre extinguisher to put it out.
Electrical safety Caution
- Read the following warnings and suggestions carefully:
- Do not open any access panel on the device when connected to the power supply. Accidental contact with the power supply may cause injury.
- Do not touch any electronic area with your hands or other tools when the machine is connected to a power supply.
- The power switch is on the back of the device. Press (-) to power it on and press (o) to power it off.

Use and maintenance

Caution: Using controls or adjustments or performance of procedures other than those speciﬁed herein may result in hazardous radiation exposure.
Cut off the power before maintaining the device.

Warning and instruction signs

On xTool S1, the warning and instruction signs are labeled where physical injuries or damage to the machine may be caused before and/or during operation.
If a sign is damaged or lost, replace it immediately. You can use the following template to print the sign you need.

Laser speciﬁcations

	Wavelength	Beam divergence	Maximum power output
Working laser	455±5 nm	1.5 mrad (IEC 60825-1 Default (simpliﬁed) evaluation C6=1)	40W/20W/10W
Indicator laser	650±5 nm	/	0.39 mW

Depending on the machine model

After-sales services

For technical support, contact us at support@xtool.com.
For more information about after-sales services, visit support.xtool.com.

Documents / Resources

	XTOOL S1 Laser Cutter [pdf] Instruction Manual D2.4.3, KD010832000, S1 Laser Cutter, S1, Laser Cutter, Cutter
	XTOOL S1 Laser Cutter [pdf] User Guide S1, S1 Laser Cutter, Laser Cutter, Cutter

References

User Manual

XTOOL S1 Laser Cutter

Product Specifications