SENECA Z-8AI Igalelo leAnalog okanye iModyuli yokuPhuma
IZILUMKISO ZOKUQALA
Igama elithi ISILUMKISO elandulelwa luphawu libonisa iimeko okanye izenzo ezibeka ukhuseleko lomsebenzisi emngciphekweni. Igama elithi ATTENTION eyandulelwe isimboli libonisa iimeko okanye izenzo ezinokuthi zonakalise isixhobo okanye isixhobo esixhunyiwe. Iwaranti iya kuba lilize kwaye ingabikho kwimeko yokusetyenziswa ngokungafanelekanga okanye tampering kunye nemodyuli okanye izixhobo ezibonelelwe ngumenzi njengoko kuyimfuneko ekusebenzeni kwayo okuchanekileyo, kwaye ukuba imiyalelo equlethwe kule ncwadana ayilandelwa.
- ISILUMKISO: Umxholo opheleleyo wale ncwadana kufuneka ufundwe phambi kwawo nawuphi na umsebenzi. Imodyuli kufuneka isetyenziswe kuphela ngabasebenzi bombane abaqeqeshiweyo.
- Amaxwebhu athile ayafumaneka kusetyenziswa i-QR-CODE eboniswe kwiphepha loku-1.
- Imodyuli kufuneka ilungiswe kwaye iindawo ezonakalisiweyo zitshintshwe nguMenzi.
- Imveliso inovelwano ngokukhutshwa kwe-electrostatic. Thatha amanyathelo afanelekileyo ngalo naluphi na umsebenzi.
- Ukulahlwa kwenkunkuma yombane neye-elektroniki (esebenzayo kwiManyano yaseYurophu nakwamanye amazwe anokurisayikilishwa). Isimboli kwimveliso okanye ukupakishwa kwayo kubonisa ukuba imveliso kufuneka inikezelwe kwiziko lokuqokelela eligunyazisiweyo ukuba lisetyenziswe ngokutsha inkunkuma yombane neye-elektroniki.
NGENKAMPANI
- SENECA srl; Nge-Austria, 26 - 35127 - PADOVA - ITALY;
- Umnxeba. +39.049.8705359
- Ifeksi +39.049.8706287
IINKCUKACHA ZOQHAKAMSHELWANO
- Uxhaso lobuchwepheshe: inkxaso@seneca.it
- Ulwazi lweMveliso: sales@seneca.it
- Olu xwebhu luyipropathi ye-SENECA srl. Iikopi kunye nokuveliswa kwakhona akuvumelekanga ngaphandle kokuba kugunyazisiwe. Umxholo wolu xwebhu uhambelana neemveliso ezichazwe kunye nobuchwepheshe.
- Idatha echaziweyo inokuguqulwa okanye yongezwe ngeenjongo zobugcisa kunye / okanye ukuthengisa.
UHLELO LWEMODYULI
- Imilinganiselo: LxHxD 17.5 x 102.5 x 111 mm;
- Ubunzima: 110g;
- Indawo ebiyelweyo: PA6, emnyama
IIMPAWU NGE-LED PHAMBILI
| I-LED | IMEKO | Intsingiselo ye-LED |
| PWR Green | ON | Isixhobo sinikwe amandla ngokuchanekileyo |
| FAIL yellow | Ukudanyaza | I-Anomaly okanye impazamo |
| I-RX Ebomvu | Ukudanyaza | Ukufunyanwa kwepakethi kugqityiwe |
| I-RX Ebomvu | ON | Okungaqhelekanga / Jonga umdibaniso |
| TX Ebomvu | Ukudanyaza | Ukuhanjiswa kwepakethi kugqityiwe |
INGCACISO YOBUGCISA
| IZIMPAWU | |
| UmqulutagIgalelo: | I-Bipolar ene-FS ecwangcisiweyo kwi +2Vdc kunye +10Vdc Input impedance>100kOhm |
| Igalelo langoku: | I-Bipolar ene-FS Programmable kwi +20mA ene-50Ohm yangaphakathi shunt ekhethiweyo nge-DIP-switch. Umbane okhoyo: 90 + 90mA kwi-13Vdc. |
| Inani lamajelo: | 8 |
| Isisombululo segalelo: | 15 bit + uphawu. |
| Ukhuseleko lwegalelo: | ± 30Vdc okanye 25mA |
| Ukuchaneka voltage kunye neyangoku: | Ukuqala: 0.1 yesikali esipheleleyo Umgca womgca : 0.03% yesikali. Iqanda: 0.05% yesikali.
TC: 100 ppm, EMI: <1 % |
| Sampixesha lokulala | 120 ms/itshaneli okanye 60 ms/itshaneli |
| Ixesha lokuhlaziya umlinganiselo (sampumyinge wexesha: 10ms) | Isitishi esi-1 sivuliwe (ixesha lohlaziyo lwetshaneli enye)
Iitshaneli ezi-4 zenziwe zasebenza (ixesha lokuhlaziya amajelo ama-4) Iitshaneli ezi-8 zenziwe zasebenza (ixesha lokuhlaziya amajelo ama-8) |
UQINISEKISO LWESETHINGI ZEFEKtri
UKUBEKA I-DIP-SWITISHI
Isikhundla se-DIP-iiswitshi sichaza iiparamitha zonxibelelwano lwebhasi ye-Mod yemodyuli: Idilesi kunye ne-Baud Rate Le theyibhile ilandelayo ibonisa i-Baud Rate kunye ne-Address values ngokwe-DIP-switch setting:
Phawula: Xa i-DIP itshintshela u-1 ukuya ku-8 IVIMILE, useto lonxibelelwano luthathwa kwiprogramming (EEPROM).
Qaphela 2: Umgca we-RS485 kufuneka upheliswe kuphela ekupheleni komgca wonxibelelwano.
Useto lweedip-switshi kufuneka luhambelane noseto olukwiirejista. Inkcazo yeerejista iyafumaneka kwi-USER MANUAL.
UKUQHAGAMSHELWA KOMbane
Ukunikezelwa kwamandla kunye ne-interface ye-Modbus ifumaneka ngokusebenzisa i-Seneca DIN ibhasi kaloliwe, nge-IDC10 isiqhagamshelo esingasemva, okanye i-Z-PC-DINAL-17.5 i-accessory.
Isidibanisi ngasemva (IDC 10)
Umzobo ubonisa iintsingiselo ze-IDC10 zezikhonkwane zokudibanisa ukuba iisignali ziza kuthunyelwa ngazo ngokuthe ngqo.
IZIMPAWU
- A) Umqulutagigalelo kunye nonikezelo loluvo olusuka kwiMODULI (13 Vdc)
- B) Umqulutagigalelo kunye nonikezelo lwesivamvo AYIZWI kwiMODULI
- C) Igalelo langoku kunye nonikezelo loluvo AKUKHO kuvela kwiMODULI
- D) Igalelo langoku kunye nobonelelo loluvo olusuka kwiMODULI (13 Vdc)
- E) Igalelo langoku elinesivamvo sombane NGAPHANDLE
QAPHELA
- Umda wonikezelo lwamandla aphezulu kufuneka ungagqithiswa, njengoko oku kunokubangela umonakalo omkhulu kwimodyuli. Cima imodyuli phambi kokudibanisa amagalelo kunye neziphumo.
- Ukuhlangabezana neemfuno zokhuselo lwe-electromagnetic:
- sebenzisa iintambo zomqondiso ezikhuselekileyo;
- qhagamshela isikhuselo kwisixokelelwano somhlaba esikhethiweyo;
- zahlula iintambo ezikhuselweyo kwezinye iintambo ezisetyenziselwa ukufakelwa kombane (ii-inverters, ii-motor, ii-oveni zokungenisa, njl njl…).
- faka i-fuse ene-MAX umthamo we-2.5A kufuphi nemodyuli.
- qinisekisa ukuba unikezelo lwamandla voltage kwimodyuli ayidluli: 40Vdc okanye 28Vac, kungenjalo imodyuli iya konakaliswa.
Amaxwebhu / Izibonelelo
 |
SENECA Z-8AI Igalelo leAnalog okanye iModyuli yokuPhuma [pdf] Incwadi Yomyalelo I-Z-8AI, i-Analog Input okanye iModyuli yePhulo, imodyuli ye-Analog, i-Z-8AI igalelo le-Analog okanye iModyuli yePhulo |
