DigiRail-4C
Imodyuli yoNgeniso ye-Counter yeDijithali
INCWADI YOMYALELO
V1.1x F
INTSHAYELELO
Imodyuli yeModbus yeeNgeniso zeDijithali- DigiRail-4C yiyunithi yombane enezinto ezine zokubala zedijithali I-RS485 ujongano lothotho luvumela ukufunda kunye noqwalaselo lwala magalelo, ngothungelwano lonxibelelwano. Ifanelekile ukunyuswa kwiireyile zeDIN ezingama-35 mm. Amagalelo afakwe ngombane kwi-interface ye-serial kunye nobonelelo lwemodyuli. Akukho ukugquma kombane phakathi kojongano lwe-serial kunye nokubonelela. Akukho ukugqunyelelwa kombane phakathi kwamagalelo 1 kunye ne-2 (itheminali engalunganga eqhelekileyo), kunye naphakathi kwamagalelo 3 kunye no-4. Ulungelelwaniso lwe DigiRail-4C lwenziwa ngojongano lweRS485 ngokusebenzisa imiyalelo yeModbus RTU. Isoftware yeDigiConfig ivumela uqwalaselo lwazo zonke iimpawu zeDigiRail kunye noxilongo lwayo. IDigiConfig inikezela ngeempawu zokubona izixhobo ezikhoyo kuthungelwano lweModbus kunye nokuqwalasela iparameters zonxibelelwano DigiRail-4C. Le ncwadana ibonelela ngemiyalelo yofako kunye noqhagamshelo lwemodyuli. Umfakeli weDigiConfig kunye namaxwebhu malunga nonxibelelwano lwe-Modbus ye DigiRail-4C (Imanyuwali yoNxibelelwano ye DigiRail-4C) ziyafumaneka ukuze zikhutshelwe www.novusautomation.com.
INGCACISO
Izimvo: I-4 ye-Digital Inputs: Inqanaba lengqiqo 0 = 0 ukuya kwi-1 Vdc; Inqanaba lengqiqo 1 = 4 ukuya kuma-35 Vdc
Unyino lwangaphakathi lwangoku kumagalelo: malunga ne-5 mA
Ubuninzi bamaza obuninzi: I-1000 Hz yemiqondiso ene-square wave kunye nomjikelo wokusebenza wama-50%. Igalelo loku-1 lingalungiselelwa ukubala imiqondiso ukuya kuthi ga kwi-100 kHz.
Umthamo wokubala (ngegalelo ngalinye): 32 bits (0 ukuya 4.294.967.295)
Ubalo olulodwa: Ukwazi ukubala ii-pulses ngamaxesha anikiweyo (izinga le-pulse) kunye nokugcina ukubala okuphezulu kwizithuba zexesha elinikiweyo (izinga eliphezulu). Amathuba exesha azimeleyo kuyo yomibini imisebenzi.
Amandla: I-10 ukuya kwi-35 Vdc / Ukusetyenziswa okuqhelekileyo: 50 mA @ 24 V. Ukukhuselwa kwangaphakathi kwi-polarity inversion.
Ukufakwa kombane phakathi kwamagalelo kunye nonikezelo/izibuko le-serial: 1000 Vdc ngomzuzu omnye
Uthotho lonxibelelwano: RS485 kwiingcingo ezimbini, Modbus RTU protocol. Iiparamitha ezilungisekayo: Isantya sonxibelelwano: ukusuka kwi-1200 ukuya kwi-115200 bps; I-Parity: edibeneyo, engaqhelekanga okanye ayikho
Isitshixo sokubuyisela iiparamitha zonxibelelwano: Isitshixo se-RCM, kwiphaneli yangaphambili, iya kumisela isixhobo kwimowudi yokuxilonga (idilesi ye-246, izinga le-baud 1200, i-parity nokuba, i-1 stop bit), ekwazi ukufunyanwa kwaye iqwalaselwe yi-software ye-DigiConfig.
Iimpawu zokukhanya zangaphambili zonxibelelwano kunye nobume:
TX: Ibonisa ukuba isixhobo sithumela idatha kumgca weRS485;
RX: Ibonisa ukuba isixhobo sifumana idatha kumgca weRS485;
Ubume: Xa isibane sivuliwe ngokusisigxina, oku kuthetha ukuba isixhobo sisebenza ngokuqhelekileyo; xa ukukhanya kudanyaza kwisithuba sesibini (malunga), oku kuthetha ukuba isixhobo sikwimo yokuxilonga.
Umququzeleli wesoftware kwindawo yeWindows: DigiConfig
Ukuhambelana kwe-electromagnetic: EN 61326:2000
Ubushushu bokusebenza: 0 ukuya kuma-70 °C
Ukufuma okunxulumene nokusebenza: I-0 ukuya kwi-90% ye-RH
Indibano: DIN 35 mm kaloliwe
Imilinganiselo: Umzobo 1 ibonisa imilinganiselo yemodyuli.
Umzobo 1 Imilinganiselo
UKUFAKWA KOMBANE
IINGCEBISO ZOKUFAKWA
- Abaqhubi bemiqondiso yokufaka kunye nonxibelelwano kufuneka badlule kwiplanti yenkqubo ehlulwe kwii-conductor zenethiwekhi yombane, ukuba kunokwenzeka, kwiindlela ezisekelwe phantsi.
- Ubonelelo lwezixhobo kufuneka lunikezelwe kwinethiwekhi efanelekileyo yezixhobo.
- Kulawulo nasekubekeni iliso kwizicelo, kubalulekile ukuqwalasela okunokuthi kwenzeke ukuba nayiphi na inxalenye yesistim inokusilela.
- Sincoma ukusetyenziswa kwe-RC FILTERS (47R kunye ne-100nF, uchungechunge) ngokuhambelana ne-contactor kunye neekhoyili ze-solenoid ezikufutshane okanye ezixhunyiwe DigiRail.
UKUQHAGAMSHELWA KOMbane
Umzobo 2 ibonisa uqhagamshelo lombane oluyimfuneko. Ii-terminals 1, 2, 3, 7, 8 kunye ne-9 zenzelwe ukudibanisa igalelo, i-5 kunye ne-6 yokubonelela ngemodyuli kunye ne-10, 11 kunye ne-12 yonxibelelwano lwedijithali. Ukufumana uqhagamshelwano olungcono lombane kunye nezihlanganisi, sincoma ukusetyenziswa kweetheminali zepini ekupheleni kwee-conductor. Kuqhagamshelo locingo oluthe ngqo, ubuncinci begeyi ecetyiswayo yi-0.14 mm², hayi ngaphezulu kwe-4.00 mm².
Qaphela xa udibanisa iitheminali zokubonelela kwi-DigiRail. Ukuba umqhubi ofanelekileyo womthombo wokubonelela uxhunyiwe, kwangomzuzwana, kwenye yee-terminals zonxibelelwano zonxibelelwano, imodyuli inokonakala.
Umzobo 2 Uqhagamshelo loMbane
Uluhlu loku-1 ibonisa indlela yokudibanisa iziqhagamshelo kujongano lonxibelelwano lweRS485:
| D1 | D | D+ | B | Umgca wedatha yeBidirectional. | Itheminali 10 |
| D0 | D | D- | A | Umgca wedatha oguqulwe kabini. | Itheminali 11 |
| C | Uqhagamshelo olukhethwayo oluphucula i | Itheminali 12 | |||
| GND | ukusebenza konxibelelwano. | ||||
Uluhlu loku-1 RS485 Uqhagamshelo
Ulwazi olongezelelweyo malunga nokuxhamla kunye nokusetyenziswa kwenethiwekhi yonxibelelwano inokufumaneka kwi-Manual yoNxibelelwano lwe-DigiRail-4C.
UQINISEKISO
Isicelo DigiConfig yinkqubo yeWindows® esetyenziselwa uqwalaselo lweemodyuli zeDigiRail. Ukufakela kwayo, sebenzisa i DigiConfigSetup.exe file, iyafumaneka kweyethu webindawo kwaye ulandele imiyalelo njengoko kubonisiwe. DigiConfig unikwa uncedo olupheleleyo file, ukunika lonke ulwazi oluyimfuneko ukuze lusetyenziswe ngokupheleleyo. Ukusebenzisa inqaku loncedo, qalisa inkqubo kwaye ukhethe imenyu ethi "Uncedo" okanye ucinezele iqhosha leF1. Yiya e www.novusautomation.com ukuze ufumane isifakeli seDigiConfig kunye neencwadana zemveliso ezongezelelweyo.
ISIQINISEKISO
Iimeko zewaranti ziyafumaneka kwi yethu web indawo www.novusautomation.com/warranty.¯
Amaxwebhu / Izibonelelo
 |
novus DigiRail-4C Digital Counter Input Module [pdf] Incwadi Yomyalelo DigiRail-4C Digital Counter Input Module, DigiRail-4C, Digital Counter Input Module |
