I-PRO MICRO
I-Microcontroller ehambelana neArduino
Incwadi yokusebenzisa
IINKCUKACHA ZAJIKELELE
mthengi othandekayo,
enkosi kakhulu ngokukhetha imveliso yethu.
Ngokulandelayo, siya kukwazisa ngento omawuyiqwalasele ngelixa uqalisa kwaye usebenzisa le mveliso.
Ukuba uhlangabezana nazo naziphi na iingxaki ezingalindelekanga ngexesha lokusetyenziswa, nceda ungathandabuzi ukuqhagamshelana nathi.
IPINETHI
Ngokuvala ibhulorho ye-solder i-J1, i-voltagi-e converter ebhodini idlula kwaye ibhodi inikezelwa ngokuthe ngqo nge-microUSB voltage okanye iphini yeVCC. Oku kukwavumela ukusebenza ukusuka ezantsi ukuya kuthi ga kwi-2.7 V.
Inqanaba lengqiqo yemodyuli ngoko kwakhona ihambelana nokunikezelwa kwevoltage.
Ingqalelo!!! Ngebhulorho yesolder evaliweyo imodyuli inokubonelelwa kuphela ngobuninzi. 5.5 V!
UKUSEKWA KWEMEKO YOPHUHLISO
Ukucwangcisa iPro Micro yakho ungasebenzisa iArduino IDE.
onokuyikhuphela apha.
Ngoku unokuseta indawo yakho yophuhliso, oku khetha phantsi kweZixhobo -> Ibhodi -> Iibhodi zeArduino AVR -> Arduino Micro.
Okokugqibela, kufuneka usete izibuko elichanekileyo apho iPro Micro yakho iqhagamshelwe kuyo.
Unokukhetha oku phantsi kweZixhobo -> Izibuko.
IKHOWUDI EXAMPLE
Ngoku ungakopa le migca ilandelayoample khowudi kwi-IDE yakho kwaye uyilayishe kwiPro Micro yakho.
Inkqubo yenza ii-LED ezimbini ezakhelwe ngaphakathi kwi-RX kunye ne-TX line blink ngokutshintshana.
IINKCUKACHA EZONGEZELELWEYO
Ulwazi lwethu kunye nezibophelelo zokuthatha-umva ngokoMthetho weSixhobo soMbane kunye ne-Electronic (ElektroG)
Uphawu kwizixhobo zombane neze-elektroniki:
Lo mgqomo wothuli unqunyulwayo uthetha ukuba izixhobo zombane neze-elektroniki azikho kwinkunkuma yasekhaya. Kufuneka ubuyisele izixhobo ezidala kwindawo yokuqokelela. Ngaphambi kokunikezelwa kweebhetri zenkunkuma kunye neziqokeleli ezingavalwanga ngesixhobo senkunkuma kufuneka zohlulwe kuyo.
Ukhetho lokubuyisela:
Njengomsebenzisi wokugqibela, ungasibuyisela isixhobo sakho esidala (esizalisekisa umsebenzi ofanayo nesixhobo esitsha esithengwe kuthi) simahla ukuze ulahlwe xa uthenga isixhobo esitsha.
Izixhobo ezincinci ezingenayo imilinganiselo yangaphandle engaphezu kwama-25 cm zinokulahlwa kubungakanani bendlu eqhelekileyo ngaphandle kokuthengwa kwesixhobo esitsha. Ukubanakho ukubuya kwindawo yethu yenkampani ngexesha lokuvula:
SIMAC Electronics GmbH, Pascalstr. 8, D-47506 Neukirchen-Vluyn, eJamani
Ukubakho kwembuyekezo kwindawo yakho:
Siza kukuthumelela ipasile stamp onokusibuyisela ngayo isixhobo ngaphandle kwentlawulo. Nceda uqhagamshelane nathi nge-imeyile Service@joy-it.net okanye ngomnxeba.
Ulwazi malunga nokupakishwa: Ukuba awunazo izinto ezifanelekileyo zokupakisha okanye awufuni ukusebenzisa eyakho, nceda uqhagamshelane nathi kwaye siya kukuthumelela ukupakisha okufanelekileyo.
INKXASO
Ukuba kusekho nayiphi na imiba elindileyo okanye iingxaki ezivela emva kokuthenga kwakho, siya kukuxhasa nge-imeyile, umnxeba kunye nenkqubo yethu yenkxaso yetikiti.
I-imeyile: service@joy-it.net
Inkqubo yetikiti: http://support.joy-it.net
Umnxeba: +49 (0)2845 9360-50 (intsimbi ye-10-17)
Ngolwazi oluthe vetshe nceda undwendwele wethu webindawo: www.ndivam.net
Ipapashwe: 27.06.2022
www.ndivam.net
I-SIMAC Electronics GmbH
Pascalstr. 8, 47506 Neukirchen-Vluyn
U-Pascalstr. 8 47506 iNeukirchen-Vluyn
Amaxwebhu / Izibonelelo
 |
UJoy-IT PRO MICRO Arduino ehambelana neMicrocontroller [pdf] Incwadi yokusebenzisa I-PRO MICRO Arduino ehambelanayo neMicrocontroller, i-PRO MICRO, iMicrocontroller ehambelana neArduino, iMicrocontroller ehambelanayo |
