iSMACONTROLLI SFAR-S-16DI-M iModyuli yokuNgenisa kunye neNkalo yeModbus
INGCACISO
| INGCACISO | ||
| Ukunikezwa Amandla | Umqulutage | 10-38 V DC; 10-28 V AC |
| Ukutya umbane | 2,4 W @ 24 V DC 3 VA @ 24 V AC | |
| Amagalelo edijithali | I-16x, ingqiqo "0": 0-3 V, ingqiqo "1": 6-36 V | |
| Izixhobo zokubala | 16x, Isisombululo 32 bits Frequency max 1 kHz | |
| Inkumbulo yezinto zokubala ezingaguquguqukiyo (FRAM) | ||
| Ukwahlukaniswa kweGalvanic | Ubukhulu be-1500 V rms | |
| Ujongano | RS485, ukuya kuthi ga kwizixhobo ezili-128 ebhasini | |
| izinga lobubi | Ukusuka kwi-2400 ukuya kwi-115200 bps | |
| Ukhuseleko lokungena | IP40 – yofakelo lwangaphakathi | |
| Ubushushu | Ukusebenza -10 ° C - +50 ° C; Ugcino – 40°C – +85°C | |
| Ubuntu bezizalwane | I-5 ukuya kwi-95% ye-RH (ngaphandle kokudibanisa) | |
| Izihlanganisi | Ubukhulu 2.5 mm2 | |
| Ubungakanani | 119,1 mm x 101 mm x 22,6 mm | |
| Ukunyuka | I-DIN yokunyuswa kukaloliwe (DIN EN 50022) | |
| Izinto Zezindlu | Iplastiki, iPC/ABS ezicimayo | |
IMIYALELO
ISILUMKISO
- Qaphela, i-wiring engalunganga yale mveliso inokuyonakalisa kwaye ikhokelela kwezinye iingozi. Qinisekisa ukuba imveliso ifakwe ngokuchanekileyo iintambo phambi kokuba uvule umbane.
- Phambi kocingo, okanye ukususa/ukunyuswa kwemveliso, qiniseka ukuba Ucime umbane. Ukusilela ukwenza oko kunokubangela ukothuka kombane.
- Sukubamba iindawo ezitshajwa ngombane njengeetheminali zombane. Ukwenza oko kunokubangela ukothuka kombane.
- Musa ukuyichitha imveliso. Ukwenza oko kunokubangela ukothuka kombane okanye ukusebenza kakubi.
- Sebenzisa imveliso ngaphakathi koluhlu lokusebenza olucetyiswayo kwinkcazo (ubushushu, ukufuma, umthamotage, ukothuka, indlela yokunyuka, umoya, njl. njl.). Ukusilela ukwenza oko kunokubangela umlilo okanye umsebenzi ongalunganga.
- Gxininisa ngokuqinileyo iingcingo kwi-terminal. Ukungaqini ngokwaneleyo kweengcingo kwitheminali kunokubangela umlilo
IZITHOMBE ZESIXHOBO 
Ufikelelo olubhalisiweyo
| Modbus | Disemba | Hex | Bhalisa Igama | Ukufikelela | Inkcazo |
| 30001 | 0 | 0x00 | Uguqulelo/Uhlobo | Funda | Inguqulelo kunye nodidi lwesixhobo |
| 30002 | 1 | 0x01 | Iiswitshi | Funda | Itshintsha imo |
| 40003 | 2 | 0x02 | Ireyithi yeBaud | Funda & Bhala | Ixabiso le-baud RS485 |
| 40004 | 3 | 0x03 | Misa amasuntswana kunye neeBits zeDatha | Funda & Bhala | Inani lokumisa amasuntswana kunye nedatha yedatha (bona |
| 40005 | 4 | 0x04 | Ukulingana | Funda & Bhala | Ubunzima |
| 40006 | 5 | 0x05 | Ukulibaziseka kwempendulo | Funda & Bhala | Ukulibaziseka kwempendulo kuNks |
| 40007 | 6 | 0x06 | Indlela yeModbus | Funda & Bhala | Imowudi yeModbus (ASCII okanye RTU) |
| 40018 | 17 | 0x11 | Isihluzi segalelo | Funda & Bhala | Uqwalaselo lwesihluzo segalelo |
|
40033 |
32 |
0x20 |
Iipakethi ezifunyenweyo ze-LSR (Ubuncinci buBalulekileyo.) |
Funda & Bhala |
Inani leepakethi ezifunyenweyo |
|
40034 |
33 |
0x21 |
Iipakethi ezifunyenweyo ze-MSR (Ezona nkcukacha ziBalulekileyo.) |
Funda & Bhala |
|
| 40035 | 34 | 0x22 | Iipakethe ezingalunganga ze-LSR | Funda & Bhala |
Inani leepakethi ezifunyenweyo ezinempazamo |
| 40036 | 35 | 0x23 | Iipakethe ezingalunganga ze-MSR | Funda & Bhala | |
| 40037 | 36 | 0x24 | Iipakethi ezithunyelweyo ze-LSR | Funda & Bhala |
Inani leepakethi ezithunyelweyo |
| 40038 | 37 | 0x25 | Iipakethi ezithunyelweyo ze-MSR | Funda & Bhala | |
| 30051 | 50 | 0x32 | Igalelo | Funda | Imeko yokufaka |
| 40053 | 52 | 0x34 | Ikhawuntara ye-1 LSR | Funda & Bhala |
32-bit counter 1 |
| 40054 | 53 | 0x35 | Ikhawuntara yoku-1 ye-MSR | Funda & Bhala | |
| 40055 | 54 | 0x36 | Ikhawuntara ye-2 LSR | Funda & Bhala |
32-bit counter 2 |
| 40056 | 55 | 0x37 | Ikhawuntara yoku-2 ye-MSR | Funda & Bhala | |
| 40057 | 56 | 0x38 | Ikhawuntara ye-3 LSR | Funda & Bhala |
32-bit counter 3 |
| 40058 | 57 | 0x39 | Ikhawuntara yoku-3 ye-MSR | Funda & Bhala | |
| 40059 | 58 | 0x3A | Ikhawuntara ye-4 LSR | Funda & Bhala |
32-bit counter 4 |
| 40060 | 59 | 0x3B | Ikhawuntara yoku-4 ye-MSR | Funda & Bhala | |
| 40061 | 60 | Ngama-0x3C | Ikhawuntara ye-5 LSR | Funda & Bhala |
32-bit counter 5 |
| 40062 | 61 | 0x3D | Ikhawuntara yoku-5 ye-MSR | Funda & Bhala | |
| 40063 | 62 | 0x3E | Ikhawuntara ye-6 LSR | Funda & Bhala |
32-bit counter 6 |
| 40064 | 63 | 0x3F | Ikhawuntara yoku-6 ye-MSR | Funda & Bhala | |
| 40065 | 64 | 0x40 | Ikhawuntara ye-7 LSR | Funda & Bhala |
32-bit counter 7 |
| 40066 | 65 | 0x41 | Ikhawuntara yoku-7 ye-MSR | Funda & Bhala | |
| 40067 | 66 | 0x42 | Ikhawuntara ye-8 LSR | Funda & Bhala |
32-bit counter 8 |
| 40068 | 67 | 0x43 | Ikhawuntara yoku-8 ye-MSR | Funda & Bhala | |
| 40069 | 68 | 0x44 | Ikhawuntara ye-9 LSR | Funda & Bhala |
32-bit counter 9 |
| 40070 | 69 | 0x45 | Ikhawuntara yoku-9 ye-MSR | Funda & Bhala |
| Modbus | Disemba | Hex | Bhalisa Igama | Ukufikelela | Inkcazo |
| 40071 | 70 | 0x46 | Ikhawuntara ye-10 LSR | Funda & Bhala |
32-bit counter 10 |
| 40072 | 71 | 0x47 | Ikhawuntara yoku-10 ye-MSR | Funda & Bhala | |
| 40073 | 72 | 0x48 | Ikhawuntara ye-11 LSR | Funda & Bhala |
32-bit counter 11 |
| 40074 | 73 | 0x49 | Ikhawuntara yoku-11 ye-MSR | Funda & Bhala | |
| 40075 | 74 | 0x4A | Ikhawuntara ye-12 LSR | Funda & Bhala |
32-bit counter 12 |
| 40076 | 75 | 0x4B | Ikhawuntara yoku-12 ye-MSR | Funda & Bhala | |
| 40077 | 76 | Ngama-0x4C | Ikhawuntara ye-13 LSR | Funda & Bhala |
32-bit counter 13 |
| 40078 | 77 | 0x4D | Ikhawuntara yoku-13 ye-MSR | Funda & Bhala | |
| 40079 | 78 | 0x4E | Ikhawuntara ye-14 LSR | Funda & Bhala |
32-bit counter 14 |
| 40080 | 79 | 0x4F | Ikhawuntara yoku-14 ye-MSR | Funda & Bhala | |
| 40081 | 80 | 0x50 | Ikhawuntara ye-15 LSR | Funda & Bhala |
32-bit counter 15 |
| 40082 | 81 | 0x51 | Ikhawuntara yoku-15 ye-MSR | Funda & Bhala | |
| 40083 | 82 | 0x52 | Ikhawuntara ye-16 LSR | Funda & Bhala |
32-bit counter 16 |
| 40084 | 83 | 0x53 | Ikhawuntara yoku-16 ye-MSR | Funda & Bhala | |
| 40085 | 84 | 0x54 | Ikhawuntara ye-1 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 1 |
| 40086 | 85 | 0x55 | Ikhawuntara yoku-1 ye-MSR | Funda & Bhala | |
| 40087 | 86 | 0x56 | Ikhawuntara ye-2 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 2 |
| 40088 | 87 | 0x57 | Ikhawuntara yoku-2 ye-MSR | Funda & Bhala | |
| 40089 | 88 | 0x58 | Ikhawuntara ye-3 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 3 |
| 40090 | 89 | 0x59 | Ikhawuntara yoku-3 ye-MSR | Funda & Bhala | |
| 40091 | 90 | 0x5A | Ikhawuntara ye-4 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 4 |
| 40092 | 91 | 0x5B | Ikhawuntara yoku-4 ye-MSR | Funda & Bhala | |
| 40093 | 92 | Ngama-0x5C | Ikhawuntara ye-5 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 5 |
| 40094 | 93 | 0x5D | Ikhawuntara yoku-5 ye-MSR | Funda & Bhala | |
| 40095 | 94 | 0x5E | Ikhawuntara ye-6 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 6 |
| 40096 | 95 | 0x5F | Ikhawuntara yoku-6 ye-MSR | Funda & Bhala | |
| 40097 | 96 | 0x60 | Ikhawuntara ye-7 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 7 |
| 40098 | 97 | 0x61 | Ikhawuntara yoku-7 ye-MSR | Funda & Bhala | |
| 40099 | 98 | 0x62 | Ikhawuntara ye-8 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 8 |
| 40100 | 99 | 0x63 | Ikhawuntara yoku-8 ye-MSR | Funda & Bhala | |
| 40101 | 100 | 0x64 | Ikhawuntara ye-9 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 9 |
| 40102 | 101 | 0x65 | Ikhawuntara yoku-9 ye-MSR | Funda & Bhala | |
| 40103 | 102 | 0x66 | Ikhawuntara ye-10 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 10 |
| 40104 | 103 | 0x67 | Ikhawuntara yoku-10 ye-MSR | Funda & Bhala |
| Modbus | Disemba | Hex | Bhalisa Igama | Ukufikelela | Inkcazo |
| 40105 | 104 | 0x68 | Ikhawuntara ye-11 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 11 |
| 40106 | 105 | 0x69 | Ikhawuntara yoku-11 ye-MSR | Funda & Bhala | |
| 40107 | 106 | 0x6A | Ikhawuntara ye-12 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 12 |
| 40108 | 107 | 0x6B | Ikhawuntara yoku-12 ye-MSR | Funda & Bhala | |
| 40109 | 108 | Ngama-0x6C | Ikhawuntara ye-13 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 13 |
| 40110 | 109 | 0x6D | Ikhawuntara yoku-13 ye-MSR | Funda & Bhala | |
| 40111 | 110 | 0x6E | Ikhawuntara ye-14 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 14 |
| 40112 | 111 | 0x6F | Ikhawuntara yoku-14 ye-MSR | Funda & Bhala | |
| 40113 | 112 | 0x70 | Ikhawuntara ye-15 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 15 |
| 40114 | 113 | 0x71 | Ikhawuntara yoku-15 ye-MSR | Funda & Bhala | |
| 40115 | 114 | 0x72 | Ikhawuntara ye-16 LSR | Funda & Bhala |
Ixabiso le-32-bit yekhawunta efakiweyo 16 |
| 40116 | 115 | 0x73 | Ikhawuntara yoku-16 ye-MSR | Funda & Bhala | |
| 40117 | 116 | 0x74 | i-Counter Config 1 | Funda & Bhala |
Uqwalaselo Lwekhawuntara
+1 – umlinganiselo wexesha (ukuba u-0 ubala iimpembelelo) +2 – Ikhawuntara yokubambisa ngokuzenzekela rhoqo ngomzuzwana omnye +4 – ixabiso lokubamba xa igalelo liphantsi +8 – seta kwakhona ikhawunta emva kokubambisa +16 – seta kwakhona isibali ukuba igalelo liphantsi +32 – umfaki khowudi |
| 40118 | 117 | 0x75 | i-Counter Config 2 | Funda & Bhala | |
| 40119 | 118 | 0x76 | i-Counter Config 3 | Funda & Bhala | |
| 40120 | 119 | 0x77 | i-Counter Config 4 | Funda & Bhala | |
| 40121 | 120 | 0x78 | i-Counter Config 5 | Funda & Bhala | |
| 40122 | 121 | 0x79 | i-Counter Config 6 | Funda & Bhala | |
| 40123 | 122 | 0x7A | i-Counter Config 7 | Funda & Bhala | |
| 40124 | 123 | 0x7B | i-Counter Config 8 | Funda & Bhala | |
| 40125 | 124 | Ngama-0x7C | i-Counter Config 9 | Funda & Bhala | |
| 40126 | 125 | 0x7D | i-Counter Config 10 | Funda & Bhala | |
| 40127 | 126 | 0x7E | i-Counter Config 11 | Funda & Bhala | |
| 40128 | 127 | 0x7F | i-Counter Config 12 | Funda & Bhala | |
| 40129 | 128 | 0x80 | i-Counter Config 13 | Funda & Bhala | |
| 40130 | 129 | 0x81 | i-Counter Config 14 | Funda & Bhala | |
| 40131 | 130 | 0x82 | i-Counter Config 15 | Funda & Bhala | |
| 40132 | 131 | 0x83 | i-Counter Config 16 | Funda & Bhala | |
| 40133 | 132 | 0x84 | Bamba | Funda & Bhala | Ukubamba ikhawuntara |
| 40134 | 133 | 0x85 | Ubume | Funda & Bhala | Ikhawuntara ethathiweyo |
ISIKHOKELO SOKUFAKA
Nceda ufunde imiyalelo phambi kokuba usebenzise okanye usebenzise isixhobo. Kwimeko yayo nayiphi na imibuzo emva kokufunda olu xwebhu, nceda uqhagamshelane neQela leNkxaso le-iSMA CONTROLLI
(support@ismacontrolli.com).
- Ngaphambi kocingo okanye ukususa / ukunyuswa kwemveliso, qiniseka ukuba ucima umbane. Ukusilela ukwenza oko kunokubangela ukothuka kombane.
- I-wiring engafanelekanga yemveliso inokuyonakalisa kwaye ikhokelela kwezinye iingozi. Qinisekisa ukuba imveliso ifakwe iintambo ngokuchanekileyo phambi kokuba uvule umbane.
- Sukubamba iindawo ezitshajwa ngombane njengeetheminali zombane. Ukwenza oko kunokubangela ukothuka kombane.
- Musa ukuyichitha imveliso. Ukwenza oko kunokubangela ukothuka kombane okanye ukusebenza kakubi.
- Sebenzisa imveliso kuphela ngaphakathi koluhlu lokusebenza olucetyiswayo kwinkcazo (ubushushu, ukufuma, umthamotage, umothuko, indlela yokunyuka, umoya, njl. njl.). Ukungakwenzi oko kunokubangela umlilo okanye umsebenzi onempazamo.
- Gxininisa ngokuqinileyo iingcingo kwi-terminal. Ukungakwenzi oko kunokubangela umlilo.
- Kuphephe ukufaka imveliso kwindawo ekufutshane nezixhobo zombane ezinamandla aphezulu kunye neentambo, imithwalo yokungenisa, kunye nezixhobo zokutshintsha. Ukusondela kwezinto ezinjalo kunokubangela ukuphazamiseka okungalawulwayo, okukhokelela ekusebenzeni okungazinzanga kwemveliso.
- Ukulungelelaniswa okufanelekileyo kwamandla kunye ne-signal cabling kuchaphazela ukusebenza kwayo yonke inkqubo yokulawula. Kuphephe ukubeka amandla kunye neengcingo zomqondiso kwiitreyi zentambo ezihambelanayo. Inokubangela ukuphazamiseka kwiimpawu ezibekwe esweni kunye nokulawula.
- Kunconywa kubalawuli bamandla / iimodyuli kunye nababoneleli bamandla be-AC / DC. Banikezela nge-insulation engcono kwaye ezinzileyo yezixhobo xa kuthelekiswa neenkqubo ze-AC / AC ze-transformer, ezihambisa ukuphazamiseka kunye neziganeko ezidlulayo ezifana nokunyuka kunye nokuqhuma kwizixhobo. Bakwahlukanisa iimveliso ezivela kwi-inductive phenomena kwezinye ii-transformers kunye nemithwalo.
- Iinkqubo zonikezelo lwamandla kwimveliso kufuneka zikhuselwe zizixhobo zangaphandle ezinciphisa ukugqithiswa kombanetage kunye neziphumo zokukhutshwa kombane.
- Gwema ukunika amandla imveliso kunye nezixhobo ezilawulwayo / ezibekwe esweni, ngakumbi amandla aphezulu kunye nemithwalo ye-inductive, ukusuka kumthombo wamandla omnye. Izixhobo zamandla ezivela kumthombo wamandla omnye zibangela umngcipheko wokwazisa ukuphazamiseka kwimithwalo ukuya kwizixhobo zokulawula.
- Ukuba i-AC / AC i-transformer isetyenziselwa ukubonelela ngezixhobo zokulawula, kucetyiswa ngamandla ukuba kusetyenziswe ubuninzi be-100 VA Class 2 transformer ukuphepha imiphumo engafunekiyo ye-inductive, eyingozi kwizixhobo.
- Imigca emide yokubeka iliso kunye nokulawula inokubangela iilophu malunga nokunikezelwa kwamandla okwabelwana ngawo, okubangela ukuphazamiseka ekusebenzeni kwezixhobo, kubandakanywa unxibelelwano lwangaphandle. Kunconywa ukusebenzisa i-galvanic separators.
- Ukukhusela umqondiso kunye nemigca yonxibelelwano ngokuchasene nokuphazamiseka kwe-electromagnetic yangaphandle, sebenzisa iintambo ezikhuselekileyo eziphantsi kunye namaso e-ferrite.
- Ukutshintshela ukuhanjiswa kwemveliso yedijithali yemithwalo emikhulu (egqithileyo) imithwalo ye-inductive kunokubangela ukuphazamiseka kwe-pulses kumbane ofakwe ngaphakathi kwemveliso. Ngoko ke, kucetyiswa ukuba kusetyenziswe ii-relays zangaphandle / abafowunelwa, njl njl ukutshintsha imithwalo enjalo. Ukusetyenziswa kwabalawuli abaneziphumo ze-triac kwakhona kunciphisa ukugqithisa okufanayotage iziganeko.
- Iimeko ezininzi zokuphazamiseka kunye nokugqithisatagkwiisistim zolawulo ziveliswa ngokutshintshwa, imithwalo ye-inductive enikezelwa ngokutshintshana kwee-mains vol.tage (AC 120/230 V). Ukuba abanazo iisekethe ezifanelekileyo ezakhelwe ngaphakathi zokunciphisa ingxolo, kucetyiswa ukuba kusetyenziswe iisekethe zangaphandle ezifana ne-snubbers, i-varistors, okanye i-diode yokukhusela ukunciphisa ezi ziphumo.
Ukufakwa kombane kule mveliso kufuneka kwenziwe ngokuhambelana neekhowudi zocingo zelizwe kwaye zihambelane nemimiselo yendawo.
iSMA CONTROLLI SpA – Via Carlo Levi 52, 16010 Sant'Olcese (GE) – Italy | support@ismacontrolli.com
www.ismacontrolli.com
Amaxwebhu / Izibonelelo
 |
iSMACONTROLLI SFAR-S-16DI-M iModyuli yokuNgenisa kunye neNkalo yeModbus [pdf] Incwadi Yomyalelo I-SFAR-S-16DI-M iModyuli yeNgeniso kunye neNgcaciso yeModyuli yeModbus, SFAR-S-16DI-M, iModyuli yeNgeniso kunye neNgcaciso yeModbus, iModyuli yeNgeniso kunye neVepayo, iModyuli yokuPhuma, iModyuli |
