I-Danfoss PLUS + 1 ehambelanayo ne-EMD ye-Speed Sensor ye-QUAD ibhloko yokuSebenza
Iinkcukacha
- Imveliso: I-PLUS+1 ethobelayo ibhloko ye-EMD ye-Speed Sensor Quadrature Function Block
- Uhlaziyo: Rev AA (May 2015)
- Umenzi: UDanfoss
Ulwazi lweMveliso
I-EMD_SPD_QUAD iBloko yokuSebenza ikhupha isignali ye-RPM kunye ne-DIR yesiginali esekelwe kwiimpembelelo ezivela kwi-EMD Speed Sensor. Ifumana amagalelo afana neSigaba A, iSigaba B, uMqulutage, kwaye Qwalasela imiqondiso ukubala RPM imveliso.
FAQ
Q: Yintoni injongo ye-EMD_SPD_QUAD iBloko yokuSebenza?
A: I-EMD_SPD_QUAD iBloko yokuSebenza ikhupha isignali ye-RPM kunye ne-DIR yesiginali esekelwe kwiimpembelelo ezivela kwi-EMD Speed Sensor.
IMILINGANISELO
www.powersolutions.danfoss.com
Imbali yohlaziyo
| Uhlaziyo | Umhla | Comment |
| Umfundisi AA | Meyi 2015 |
©2015 Danfoss Power Solutions (US) Inkampani. Onke Amalungelo Agciniwe.
Zonke iimpawu zokurhweba kwesi sixhobo ziipropati zabanini bazo.
I-PLUS + 1, i-GUIDE, kunye ne-Sauer-Danfoss ziimpawu zentengiso zeDanfoss Power Solutions (US) Company. I-Danfoss, i-PLUS + 1 GUIDE, i-PLUS + 1 ehambelanayo, kunye ne-logotypes ye-Sauer-Danfoss ziimpawu zorhwebo zeDanfoss Power Solutions (US) Inkampani.
Ngaphezuluview
Le bloko yomsebenzi ikhupha isibonakaliso se-RPM kunye nesignali ye-DIR esekelwe kwiigalelo ezivela kwi-EMD Speed Sensor.
Kwi-MC kunye nomlawuli we-SC, le bhloko yomsebenzi ifumana:
- Igalelo leSigaba A nge-MFin.
- Igalelo leSigaba B nge-MFin.
Igalelo
EMD_SPD_QUAD Ungeniso lweBloko yokuSebenza
| Igalelo | Uhlobo | Uluhlu | Inkcazo |
| IParam | —- | —- | Igalelo lomsebenzisi-elichaziweyo I-Pulse/Rev ixabiso elichaza inani leentshukumo ezilingana nerevolution enye.
Ngokuzikhethela, igalelo le-a DirLockHz ixabiso lokubuyisela lo msebenzi ibhloko yempazamo yangaphakathi yesalathiso-isitshixo ixabiso lefrikhwensi. |
| Isigaba A | Ibhasi | —- | Isantya songeniso kunye nezalathisi zezalathisi ezivela kwisivamvo sesantya. |
| Per | U32 | 1,250 ukuya
10,000,000 |
Isiphumo sexesha elilinganisiweyo yi Inzwa yesantya.
Ibhloko yomsebenzi isebenzisa i Per uphawu, Bala uphawu, kwaye Puls/Rev ixabiso leparameter ukubala RPM imveliso. 10,000 = 1,000 μs. |
L1429531 · Rev AA · May 2015
EMD_SPD_QUAD Ungeniso lweBloko yokuSebenza
| Igalelo | Uhlobo | Uluhlu | Inkcazo |
| Bala | U16 | 0 ukuya 65,535 | Ubalo olulinganisiweyo ngemveliso yelophu yenkqubo nge Inzwa yesantya.
Ibhloko yomsebenzi isebenzisa i Per uphawu, Bala uphawu, kwaye Puls/Rev ixabiso leparameter ukubala RPM imveliso. 1,000 = 1,000. |
| QuadCount | S16 | -32768 ukuya
32767 |
Ulwalathiso olulinganisiweyo kunye nenani lamanani asekelwe kwisigaba esitshintshiweyo samaza e-pulse ukusuka Isigaba A
kwaye Isigaba B. 1,000 = 1,000. |
| IVolt/Voltage | U16 | 0 ukuya 5,250 | Umthamo olinganisiweyotage yophawu lwegalelo oluphuma kwiSensom yesantya, ethi ibhloko isebenzise ubhaqo lwempazamo. |
| Qwalasela | Ibhasi engaphantsi | —- | Iqulethe imiqondiso emisela eli galelo. |
| Isigaba B | Ibhasi | —- | Ukufakwa kwemiqondiso yesantya ukusuka kwisivamvo sesantya. |
| Per | U32 | 1,250 ukuya
10,000,000 |
Isiphumo sexesha elilinganisiweyo yi Inzwa yesantya.
Ibhloko yomsebenzi isebenzisa i Per uphawu, Bala uphawu, kwaye Puls/Rev ixabiso leparameter ukubala RPM imveliso. 10,000 = 1,000 μs. |
| Bala | U16 | 0 ukuya 65,535 | Ubalo olulinganisiweyo ngemveliso yelophu yenkqubo nge Inzwa yesantya.
Ibhloko yomsebenzi isebenzisa i Per uphawu, Bala uphawu, kwaye Puls/Rev ixabiso leparameter ukubala RPM imveliso. 1,000 = 1,000. |
| IVolt/Voltage | U16 | 0 ukuya 5,250 | Umthamo olinganisiweyotage yophawu lwegalelo oluphuma kwiSensom yesantya, ethi ibhloko isebenzise ubhaqo lwempazamo. |
| Qwalasela | Ibhasi engaphantsi | —- | Iqulethe imiqondiso emisela eli galelo. |
Iziphumo
EMD_SPD_QUAD iZiphumo zeBloko yokuSebenza
| Isiphumo | Uhlobo | Uluhlu | Inkcazo |
| Ubume | U16 | —- | Inika ingxelo yobume bebhloko yomsebenzi.
Le block umsebenzi isebenzisa a non-standard i-bitwise scheme ukuxela isimo sayo kunye neempazamo. · 0x0000 = Ibhloko ilungile. · 0x0008 = Puls/Rev or DirLockHz ixabiso leparameter liphumile kuluhlu. |
| Impazamo | U16 | —- | Uxela iimpazamo zebhloko yomsebenzi.
Le block umsebenzi isebenzisa a non-standard i-bitwise scheme ukuxela isimo sayo kunye neempazamo. · 0x0000 = Ibhloko ilungile. · 0x0001 = Per uphawu kwibhloko yomsebenzi Isigaba A igalelo liphantsi kakhulu. · 0x0002 = IVolt/Voltage uphawu kwibhloko yomsebenzi Isigaba A igalelo liphumile kuluhlu. · 0x0004 = Per uphawu kwibhloko yomsebenzi Isigaba B igalelo liphantsi kakhulu. · 0x0008 = IVolt/Voltage uphawu kwibhloko yomsebenzi Isigaba B igalelo liphumile kuluhlu. · 0x0010 =Umahluko kwiifrikhwensi ezixelwe yibhloko yomsebenzi Isigaba A kwaye Isigaba B amagalelo makhulu kune-5%. |
| Idayigi | —- | —- | Iziphumo zebhasi nge Ngokuphindaphindiweyo, FltTmrPhase A, FltTmrPhase B, kwaye FltTmrFreqDiff Iimpawu ezikhoyo zokusombulula ingxaki. |
| Ngokuphindaphindiweyo | U32 | 0 ukuya kwi-1,000,
000,000 |
Umlinganiselo ophindaphindiweyo weSensom yesantya. 100,000 = 10,000 Hz. |
| FltTmrPhase A | U16 | 0 ukuya 65,535 | Xa impazamo yefrikhwensi:
· Kwenzeka, le mveliso ibala imilliseconds de ibhloko yomsebenzi yenze isibhengezo sempazamo. · Icoca, isiphumo sibala phantsi iimilliseconds de umsebenzi ucime isibhengezo sempazamo. 1,000 = 1,000 ms. |
| FltTmrPhase B | U16 | 0 ukuya 65,535 | Xa impazamo yefrikhwensi:
· Kwenzeka, le mveliso ibala imilliseconds de ibhloko yomsebenzi yenze isibhengezo sempazamo. · Icoca, isiphumo sibala phantsi iimilliseconds de umsebenzi ucime isibhengezo sempazamo. 1,000 = 1,000 ms. |
| FltTmrFreqDiff | U16 | 0 ukuya 65,535 | Xa impazamo yomahluko wefrikhwensi:
· Kwenzeka, le mveliso ibala imilliseconds de ibhloko yomsebenzi yenze isibhengezo sempazamo. · Icoca, isiphumo sibala phantsi iimilliseconds de umsebenzi ucime isibhengezo sempazamo. 1,000 = 1,000 ms. |
| I-dRPM | U16 | 0–25,000 | Iirevolutions zoluvo lwesantya ngomzuzu x 10 (deciRPM). Ibhloko yomsebenzi clamps le mveliso kwi-25,000.
1 = 0.1 rpm. |
| RPM | U16 | 0–2,500 | Utshintsho lwesivamvo sesantya ngomzuzu.
Ibhloko yomsebenzi clamps le mveliso kwi-2,500. 1 = 1 rpm. |
EMD_SPD_QUAD iZiphumo zeBloko yokuSebenza
| Isiphumo | Uhlobo | Uluhlu | Inkcazo |
| Dir | S8 | -1, 0, +1 | Indlela yokujikeleza yeSensom yesantya.
· -1 = Counterclockwise (CCW). · 0 = Phakathi. · +1 = Ngokwewotshi (CW). |
Malunga Connections Block Umsebenzi
Umsebenzi Block Connections
| Into | Inkcazo |
| 1. | Igalelo leeparamitha eziqhelekileyo ezinokusetyenziswa kwiibhloko zemisebenzi emininzi. |
| 2. | Igalelo lebhasi ene:
· Umqulutage, ixesha, Isibalo sesine, kwaye ubale imiqondiso ephumayo yi-EMD Speed Sensor. · I-sub-bus enemiqondiso emisela igalelo lomlawuli elifumana le miqondiso. |
| 3. | Igalelo lebhasi ene:
· Umqulutage, ixesha, Isibalo sesine, kwaye ubale imiqondiso ephumayo yi-EMD Speed Sensor. · I-sub-bus enemiqondiso emisela igalelo lomlawuli elifumana le miqondiso. |
| 4. | Inika ingxelo ngobume bebhloko yomsebenzi. |
| 5. | Inika ingxelo ngempazamo yebhloko yomsebenzi. |
| 6. | Iziphumo zebhasi nge Ngokuphindaphindiweyo, FltTmrPhase A, FltTmrPhase B, kwaye FltTmrFreqDiff Iimpawu ezikhoyo zokusombulula ingxaki. |
| 7. | Utshintsho lwesivamvo sesantya ngomzuzu. |
| 8. | Iirevolutions zoluvo lwesantya ngomzuzu x 10 (deciRPM). |
| 9. | Indlela yokujikeleza yeSensom yesantya.
· -1 = Counterclockwise (CCW). · 0 = Phakathi. · +1 = Ngokwewotshi (CW). |
Ubume kunye neNgqiqo yeFault
Ngokungafaniyo nezinye iibhloko zokusebenza ezithobelayo ze-PLUS + 1, le bhloko yomsebenzi isebenzisa imeko engekho mgangathweni kunye neekhowudi zeempazamo.
Ingqiqo yesimo
| Ubume | Hex* | Ibhinary | Unobangela | Impendulo | Ukulungiswa |
| Iparamitha iphumile kuluhlu. | 0x0008 | 1000 | Puls/Rev, FaultDetTm, okanye DirLockHz iparameter iphumile kuluhlu. | Ibhloko yomsebenzi clamps ixabiso elingaphandle kuluhlu nokuba kungaphezulu okanye kumda osezantsi. | Fumana iparamitha engaphandle koluhlu emva koluhlu lwayo. |
* I-Bit 16 isetelwe kwi-1 ichonga ubume beDanfoss obuqhelekileyo okanye ikhowudi yempazamo.
I-Fault Logic
| Impazamo | Hex* | Ibhinary | Unobangela | Impendulo | Ukulibazisa† | Latch‡ | Ukulungiswa |
| Per uphawu kwibhloko yomsebenzi Isigaba A igalelo liphantsi kakhulu. | 0x0001 | 00000001 | Per uphawu <1,250 Hz. | Ibhloko yomsebenzi ikhupha ubuninzi bayo RPM kwaye I-dRPM
ixabiso. |
Y | N | Jonga imiba yehardware, njengengxolo yombane, enokuvelisa into engasebenziyo Per uphawu
ixabiso. |
| IVolt uphawu kwibhloko yomsebenzi Isigaba
A igalelo liphumile kuluhlu. |
0x0002 | 00000010 | 2000 V IVolt uphawu
<3000 V. |
Ibhloko yomsebenzi ikhupha i-0 ye RPM kwaye I-dRPM ixabiso. | Y | N | Jonga imiba yehardware, enje ngocingo lomqondiso wesekethe evulekileyo okanye isivamvo esilahlekileyo voltagUkubonelela. |
| Per uphawu kwibhloko yomsebenzi Isigaba B igalelo liphantsi kakhulu. | 0x0004 | 00000100 | Per uphawu <1,250 Hz. | Ibhloko yomsebenzi ikhupha ubuninzi bayo RPM kwaye I-dRPM
ixabiso. |
Y | N | Jonga imiba yehardware, njengengxolo yombane, enokuvelisa into engasebenziyo Per uphawu
ixabiso. |
| IVolt uphawu kwibhloko yomsebenzi Isigaba B igalelo liphumile
yoluhlu. |
0x0008 | 00001000 | 2000 V IVolt uphawu
<3000 V. |
Ibhloko yomsebenzi ikhupha i-0 ye RPM kwaye I-dRPM ixabiso. | Y | N | Jonga imiba yehardware, enje ngocingo lomqondiso wesekethe evulekileyo okanye isivamvo esilahlekileyo voltagUkubonelela. |
| Umahluko olinganisiweyo phakathi Isigaba A kwaye Isigaba B
I-frequency inkulu kakhulu. |
0x0010 | 00010000 | |Freq A -Freq B| > 5% yefrikhwensi yangoku. | Akukho mpendulo eyakhelwe-ngaphakathi, isiphumo esichazwe njengoko silinganiswe ngu Isigaba A igalelo. | Y | N | Jonga imiba yehardware, njengengxolo yombane, enokuvelisa into engasebenziyo Per ixabiso lomqondiso. |
I-Bit 16 iseti kwi-1 ichonga ubume beDanfoss obuqhelekileyo okanye ikhowudi yempazamo.
Isiphoso esilibazisekileyo sixelwa ukuba imeko yesiphoso efunyenweyo iyaqhubeka ngexesha elithile lokulibaziseka. Isiphoso esilibazisekileyo asinakucocwa de imeko yesiphoso ihlale ingabonwa ngexesha lokulibaziseka.
Ibhloko yomsebenzi igcina ingxelo yempazamo eqhagamshelweyo de i-latch ikhuphe.
Ixabiso leParameter yeBhlokhi yoMsebenzi
Ngenisa umgangatho ophezulu wephepha le EMD_SPD_QUAD ibhlokhi yomsebenzi ukuze view kwaye utshintshe iiparameters zebhloko yomsebenzi.
IiParameters zeBhloko yoMsebenzi
| Igalelo | Uhlobo | Uluhlu | Inkcazo |
| Puls/Rev | U16 | 20–120, 180 | Inani lee-pulses kwi-revolution ye-Speed Sensor. Jonga kwi-EMD Speed Sensor Information Information (Danfoss inxalenye L1017287) ngexabiso elichanekileyo. |
| FaultDetTm | U16 | —- | Icwangcisa ixesha phakathi kwaxa ibhloko yokusebenza ibhaqa:
· Imeko yesiphoso aze enze isibhengezo sempazamo. · Icociwe imeko yesiphoso emva koko kucinywe isibhengezo sesiphoso. 1,000 = 1,000 ms. |
| DirLockHz | U16 | 0–8,000 Hz | Icwangcisa amaxesha amaninzi apho ibloko yomsebenzi itshixa iDir output. Ngaphezulu kwesi sihlandlo, ibhloko yomsebenzi ayixeli utshintsho kwicala.
1,000 = 1,000 Hz. |
UMlawuli we-MC-Uqwalaselo lwegalelo
Ukuba unomlawuli we-SC
Uhambisa indlela yebhloko yomsebenzi:
Amagalelo eSigaba A kunye neSigaba B nge-MFin.
Kufuneka utshintshe i MFIn ulungelelwaniso olungagqibekanga ukwamkela la magalelo.
Uyiqwalasela njani i-MFin
- Kwithempleyithi ye-GUIDE, ngenisa iphepha leeNgeniso.
- Ngenisa iphepha le-MFin elifumana igalelo.
- Yenza utshintsho oluboniswe kumfanekiso owandulelayo.
UMlawuli we-SC-Uqwalaselo lwegalelo
Ukuba unomlawuli we-MC
Uhambisa le block yomsebenzi:
Amagalelo eSigaba A kunye neSigaba B nge-MFin.
Kufuneka utshintshe uqwalaselo olungagqibekanga lwe MFIn ukuze wamkele eligalelo.
I-MFin oyisebenzisayo kufuneka ibenakho igalelo leFreq kwaye ibe neBias eqwalaselweyo, uRange, kunye neMode yokuNgena amaxabiso.
Uyiqwalasela njani i-MFin
- Kwithempleyithi ye-GUIDE, ngenisa iphepha leeNgeniso.
- Ngenisa iphepha le-MFin elifumana igalelo.
- Yenza utshintsho oluboniswe kumfanekiso owandulelayo.
Iimveliso esizinikezelayo
- I-Bent Axis Motors
- ISekethe evaliweyo i-Axial Piston
Iimpompo neeMotors - Imiboniso
- Amandla e-Electrohydraulic
Ukuqhuba - Electrohydraulic
- Ulawulo lwaMandla oHydraulic
- Iinkqubo ezidibeneyo
- Imivuyo kunye noLawulo
Izibambo - Microcontroller kunye
Isoftware - Vula iSekethe yeAxial Piston
Iimpompo - IiMotor zeOrbital
- PLUS+1™ ISIKHOKELO
- Iivalvu ezilinganayo
- Izivamvo
Danforss Power Solutions ngumenzi wehlabathi jikelele kunye nomthengisi we-hydraulic ekumgangatho ophezulu kunye nezinto zombane. Sisebenza ngokukhethekileyo ekuboneleleni ngetekhnoloji yanamhlanje kunye nezisombululo ezigqwesileyo kwiimeko ezinzima zokusebenza kwintengiso ye-mobile off-highway. Ukwakha kubuchwephesha bethu bezicelo ezibanzi, sisebenza ngokusondeleyo nabathengi bethu ukuqinisekisa ukusebenza okugqwesileyo kuluhlu olubanzi lwezithuthi ezihamba kuhola wendlela. Sinceda ii-OEMs emhlabeni jikelele ukukhawulezisa uphuhliso lwenkqubo, ukunciphisa iindleko kunye nokuzisa izithuthi ekuthengiseni ngokukhawuleza. I-Danfoss-Iqabane lakho elinamandla kwi-Mobile Hydraulics.
Yiya e www.powersolutions.danfoss.com ngolwazi oluthe kratya lwemveliso.
- Naphi na apho iimoto eziphuma kuhola wendlela zisemsebenzini, kunjalo noDanfoss.
- Sinikezela ngenkxaso yeengcali kwihlabathi liphela kubathengi bethu, siqinisekisa ezona zisombululo zibalaseleyo zokusebenza. Kwaye ngothungelwano olubanzi lwe-Global Service Partners, sikwabonelela ngenkonzo ebanzi yehlabathi kuwo onke amacandelo ethu.
- Nceda uqhagamshelane nommeli weDanfoss Power Solution okufutshane nawe.
Idilesi yendawo:
UDanfoss
Power Solutions US Company 2800 East 13th Street
Ames, IA 50010, USA
Ifowuni: +1 515 239-6000
UDanfoss
Izisombululo zaMandla GmbH & Co. OHG Krokamp 35
D-24539 Neumünster, eJamani Ifowuni: +49 4321 871 0
UDanfoss
Izisombululo zaMandla i-ApS Nordborgvej 81
DK-6430 Nordborg, Denmark Phone: +45 7488 4444
Danfoss Ltd.
Izisombululo zamandla
B#22, No. 1000 Jin Hai Rd. Shanghai 201206, China Phone: +86 21 3418 5200
UDanfoss akanakwamkela uxanduva lweempazamo ezinokwenzeka kwiikhathalogu, iincwadana kunye nezinye izinto eziprintiweyo. I-Danfoss inelungelo lokutshintsha iimveliso zayo ngaphandle kwesaziso. Oku kusebenza nakwiimveliso esele zicwangciswe ngokuxhomekeke ekubeni olo tshintsho lunokwenziwa ngaphandle kotshintsho olulandelayo oluyimfuneko kwiinkcukacha esele kuvunyelwene ngazo.
Zonke iimpawu zokuthengisa kule mpahla ziyipropathi yeenkampani ezifanelekileyo. I-Danfoss kunye ne-logotype ye-Danfoss ziimpawu zorhwebo zeDanfoss Power Solutions (US) Company. Onke Amalungelo Agciniwe.
L1429531 · Rev AA · May 2015
©2015 Danfoss Power Solutions (US) Inkampani
Amaxwebhu / Izibonelelo
 |
I-Danfoss PLUS + 1 ehambelanayo ne-EMD ye-Speed Sensor ye-QUAD ibhloko yokuSebenza [pdf] Incwadi yokusebenzisa I-PLUS 1 ehambelanayo ne-EMD ye-Speed Sensor ye-QUAD ibhloko yokuSebenza, i-PLUS 1, ibhloko yokuSebenza ye-EMD ye-Speed Sensor ye-QUAD, ibhloko yokuSebenza i-Speed Sensor ye-QUAD, ibhloko yokuSebenza ye-QUAD, ibhloko yokuSebenza ye-QUAD, ibhloko yokuSebenza |