clare CLR-C1-FFZ One Flood Temperature Sensor
Intshayelelo
The Flood Temperature Sensor, designed for indoor residential and light commercial use, monitors for water leaks and significant temperature variations. Easily installed in areas prone to water exposure or temperature fluctuations, it ensures timely alerts to protect against potential damage.
Phambi koFakelo
Ensure the sensor is powered and activated. It’s crucial to add the sensor to your security system prior to physical installation.
Adding the Sensor to Your Control Panel
- Access Settings: Tap the Hamburger menu on your panel’s display.
- Security Access: Enter your master passcode to access the settings menu.
- Select ‘Devices’: Navigate to the “Devices” option.
- Register New Sensor: Tap the “+” icon, then select “Water” as the sensor type.
- Prepare Sensor for Setup: Press the test button located on the bottom of the sensor.
- Complete Sensor Setup: Follow the panel’s on-screen instructions to add the sensor to your system.
Ukuhlohla
To ensure optimal functionality, the Sensor should be installed with its four contact points directly facing down towards the floor or any level surface. This specific orientation is critical for the sensor to accurately monitor and alert you to the presence of water, high, or low temperature variations. For best results, place the sensor on the floor or a flat surface beneath sinks, refrigerators, or near any potential water sources. Adhering to this installation guideline guarantees the sensor’s effective operation, ensuring you receive alerts for any detected water, high, or low temperatures.
Installation Steps for the Flood Temperature Sensor
- Select Installation Location: Choose a spot on the floor or any flat surface beneath sinks, refrigerators, or close to potential water sources where the sensor can monitor effectively.
- Position the Sensor: Ensure the sensor’s four contact points are directly facing down towards the surface. This correct orientation is crucial for the sensor to accurately detect water presence and temperature variations.
Understanding Sensor Alerts
When the Flood Temperature Sensor identifies water leaks or notable temperature variations, it signals the security system, activating the alarm protocol. This includes:
- I-Siren evakalayo: The system triggers a loud siren to immediately draw attention to the alarm condition.
- Bomvu Splash Screen: A red splash screen is displayed on the security system’s display, visually signaling the alarm condition to the user.
- Iselula Alerts: Users are also notified through alerts sent to their mobile devices, ensuring they are informed of the alarm condition. Requires a compatible service plan.
- Umbindi Monitoring Notification: For systems integrated with a Central Monitoring Station, all event information is automatically relayed.
Special Note on Sensor Behavior and Alarm Conditions:
- Detection and Alarm Activation: When the sensor identifies a condition—be it water leakage, high temperature, or low temperature—it sends a detection signal three times within a 40-second interval. This action triggers the security panel to initiate an alarm condition.
- Alarm Clearance and Signal Pause: After the alarm condition is cleared on the panel, the system temporarily suspends recognition of subsequent signals of the same nature for one minute. This pause is designed to prevent repetitive alarms from the identical detection.
- Sensor Reset and Alarm Reactivation: The sensor returns to its normal monitoring state once the detected condition is resolved. However, if the condition persists for over an hour and the sensor sends its regular ‘heartbeat’ signal (every 60 minutes) with the detection status still active, the panel may re-enter an alarm condition.
Isondlo
Ukubuyisela ibhetri
The Flood Temperature Sensor is designed to provide reliable monitoring for water leaks and temperature fluctuations, requiring a single CR2450 3.0V (600mAh) battery for operation. Ensuring the correct battery type and installation is crucial for the sensor’s performance and safety.
ISILUMKO – UMNGCIPHEKO WOKUPHUHLUKA UKUBA IBHETRI ITSHANTSHWE LUHLOBO OLUSAYIFANELEKILEYO.
To replace the battery and ensure optimal performance of the Flood Temperature Sensor, follow these steps:
- Access the Battery Compartment: Use a screwdriver to carefully remove the screw covers from the sensor casing.
- Remove the Battery Cover: Unscrew the screws from the plastic casing and gently lift the front cover to reveal the battery compartment.
- Replace the Battery: Carefully remove the old CR2450 3.0V (600mAh) battery and insert a new one, ensuring the positive (+) side is facing up.
- Reassemble the Sensor: Align the front cover back onto the sensor casing and secure it with the screws. Replace the screw covers to finish.
Ukuvavanya inzwa yakho
Testing the Sensor Connection
After installing the Flood Temperature Sensor, perform the following steps to confirm its proper connection and communication with your monitoring system, please test the system once per week:
- Access Settings: On your monitoring system’s control panel, tap the Hamburger menu icon to access the main settings.
- Input Master Passcode: Enter your master passcode to gain access to the system’s advanced settings.
- Select Test: From the available options, select the ‘Test’ function. This mode is specifically designed for testing system components without triggering actual alerts.
- Navigate to Sensors: Within the Test mode, find and select the ‘Sensors’ option. This will allow you to specifically test the connection and functionality of connected sensors.
- Press the Test Button: Once prompted by the system, locate and press the test button at the bottom of the sensor. This action sends a signal to the monitoring system, simulating an event to verify the sensor’s communication link.
Flood Detection Test
Confirm the sensor’s ability to accurately identify the presence of water.
- Prepare a Wet Environment: Use a damp cloth or sponge to gently wet the surface directly beneath the sensor, simulating a flood scenario. Avoid immersing the sensor or allowing water to enter its casing.
- Observe the Response: An alert on your security system indicates successful detection.
Temperature Alert Test
Ensure the sensor effectively recognizes and alerts for both high and low temperature thresholds.
- High Temperature Test: Gradually increase the ambient temperature around the sensor to exceed 95°F (35°C) using a safe heat source, held at a distance.
- Low Temperature Test: Reduce the ambient temperature below 41°F (5°C) using safe cooling methods, such as placing the sensor near a cold pack or in a cooler environment. Do not expose the sensor to direct moisture.
- Monitor Alerts: For each test, observe if the sensor transmits an alert to the security system as temperatures pass the specified thresholds.
Iinkcukacha
| Inkcazo | Iinkcukacha |
| Compatible Panel | XP02 |
| I-Transmitter Frequency | 433.95MHz |
| Transmitter Frequency Tolerance | ±100KHz |
| Uluhlu olungenazintambo | Approximately 295 ft, open air, with XP02 panel |
| Uguqulelo oluntsonkothileyo | Ewe |
| TampTshintsha | Ewe |
| Isithuba sokuLawula | 60 Imizuzu |
| Iimpawu eziThunyelweyo | Ibhetri elisezantsi
High Temperature, Low Temperature Flood Detection Supervisory Uvavanyo |
| Uhlobo Lwebhetri | CR2450 3.0V (580mAh) x1 |
| Ubomi Bebhetri | at least 1 year |
| Imilinganiselo | 2.48 x 0.68 inches (Diameter x Depth) |
| Ubushushu bokusebenza | 32° ukuya ku-120.2°F (0° ukuya ku-49°C) |
| Ukumelana neMozulu | IPX7 |
| Umenzi | I-SyberSense |
| Ulwazi loLawulo | Ukuthotyelwa kweFCC |
*Battery life: Not Tested by ETL
Ingxelo yokuThobela yeFCC
Esi sixhobo sithobela iCandelo le-15 leMithetho yeFCC. Ukusebenza kuxhomekeke kwezi meko zimbini zilandelayo:
- Esi sixhobo asinakubanga uphazamiseko oluyingozi, kunye
- Esi sixhobo kufuneka samkele naluphi na uphazamiseko olufunyenweyo, kuquka uphazamiseko olunokuthi lubangele ukusebenza okungafunekiyo kwesixhobo.
Utshintsho okanye uhlengahlengiso olungavunywanga ngokucacileyo liqela elinoxanduva lokuthotyelwa lunokuphelisa igunya lomsebenzisi lokusebenzisa isixhobo.
Esi sixhobo sivavanyiwe saza safunyanwa sithobela imida yesixhobo sedijithali soDidi B, ngokungqinelana neCandelo le-15 leMithetho yeFCC. Le mida yenzelwe ukubonelela ngokhuseleko olufanelekileyo ekuphazamisekeni okuyingozi kwindawo yokuhlala. Esi sixhobo sivelisa, sisebenzise kwaye sinokusasaza amandla amaza erediyo kwaye, ukuba asifakanga kwaye sisetyenziswa ngokuhambelana nemiyalelo, sinokubangela uphazamiseko oluyingozi kunxibelelwano lwerediyo. Nangona kunjalo, akukho siqinisekiso sokuba ukuphazamiseka akuyi kwenzeka kufakelo oluthile.
Ukuba esi sixhobo sibangela uphazamiseko oluyingozi kunomathotholo okanye ulwamkelo lukamabonakude, olunokumiselwa ngokucinywa nokulayita isixhobo, umsebenzisi uyakhuthazwa ukuba azame ukulungisa uphazamiseko ngenye okanye ngaphezulu kwezi ndlela zilandelayo:
- Jongisa kwakhona okanye uhambise i-eriyali efumanayo.
- Yandisa ukwahlukana phakathi kwesixhobo kunye nomamkeli.
- Qhagamshela izixhobo kwindawo yokuphuma kwisekethe eyahlukileyo kuleyo apho umamkeli aqhagamshelwe khona.
- Dibana nomthengisi okanye igcisa likanomathotholo/kumabonakude ukuze ufumane uncedo.
Esi sixhobo sithobela imida yokuvezwa kwemitha yeFCC emiselwe indawo engalawulwayo. Esi sidlulisi akufuneki sibe kwindawo enye okanye sisebenze kunye nayo nayiphi na enye i-eriyali okanye isidluliseli.
IiNgxelo zokuThobela i-ISED
Esi sixhobo siqulathe abathumeli-mvume/abamkeli (aba)mkeli abathobela i-Innovation, iSayensi kunye noPhuhliso loQoqosho lwe-RSS(ii)layisenisi-ekhutshiweyo zaseKhanada. Umsebenzi uxhomekeke kwezi meko zimbini zilandelayo:
- Esi sixhobo sisenokungabangeli ukuphazamiseka.
- Esi sixhobo kufuneka samkele naluphi na uphazamiseko, kuquka uphazamiseko olunokubangela ukusebenza okungafunekiyo kwesixhobo.
Ingxelo ye-ISED yeRadiation Exposure
Esi sixhobo sithobela i-IC RSS-102 imida yokuvezwa kwemitha emiselwe indawo engalawulwayo. Esi sidlulisi akufuneki sibe kwindawo enye okanye sisebenze kunye nayo nayiphi na enye i-eriyali okanye isidluliseli.
ISILUMKISO
Use Only Batteries Specified in Marking. Use of A Different Battery May Have Detrimental Effect on Product Operation”
Iwaranti kunye neZaziso zoMthetho
Fumana iinkcukacha zeWaranti yoMnyino wemveliso kwi snapone.com/legal/ okanye ucele ikopi yephepha kwiNkonzo yabaThengi kwi-866.424.4489. Fumana ezinye izibonelelo zomthetho, ezifana izaziso zolawulo kunye patent kunye nolwazi lokhuseleko, at snapone.com/legal/ .
Copyright ©2024, Snap One, LLC. All rights reserved. Snap One its respective logos are registered trademarks or trademarks of Snap One, LLC (formerly known as Wirepath Home Systems, LLC), in the United States and/or other countries. Clare is also a trademark of Snap One, LLC. Other names and brands may be claimed as the property of their respective owners. Snap One makes no claim that the information contained herein covers all installation scenarios and contingencies, or product use risks. Information within this specifcation subject to change without notice. All specifcations subject to change without notice.
Imibuzo ebuzwa qho
Umbuzo: Kufuneka ndiyibuyisele kangaphi ibhetri?
A: The battery should be replaced when it no longer powers the sensor effectively or at least once a year for optimal performance.
Amaxwebhu / Izibonelelo
 |
clare CLR-C1-FFZ One Flood Temperature Sensor [pdf] Isikhokelo soFakelo CLR-C1-FFZ, CLR-C1-FFZ One Flood Temperature Sensor, One Flood Temperature Sensor, Flood Temperature Sensor, Temperature Sensor, Sensor |