I-LS XEC-DP32 / 64H isiLawuli esiQinisekileyo esiQinisekayo

Esi sikhokelo sofakelo sibonelela ngolwazi olulula lomsebenzi wolawulo lwe-PLC. Nceda ufunde ngononophelo olu xwebhu lwedatha kunye neencwadana ngaphambi kokusebenzisa iimveliso. Ngokukodwa funda amanyathelo okhuseleko kwaye uphathe iimveliso ngokufanelekileyo.

ImiGaqo yoKhuseleko

Intsingiselo yesilumkiso kunye nombhalo wokulumkisa

ISILUMKISO: ibonisa imeko enokuba yingozi enokuthi, ukuba ayiphetshwa, ingabangela ukufa okanye ukwenzakala okumandundu.

ISILUMKO: ibonisa imeko enokuba yingozi enokuthi, ukuba ayiphetshwa, ingabangela ukwenzakala okungephi okanye okuphakathi. Isenokusetyenziswa ukulumkisa ngokuchasene nezenzo ezingakhuselekanga.

ISILUMKISO

1. Musa ukuqhagamshelana neetheminali ngelixa umbane usetyenziswa.
2. Khusela imveliso ekungenwe kuyo yintsimbi yangaphandle.
3. Musa ukuyisebenzisa kakubi ibhetri (ukutshaja, ukuqhaqha, ukubetha, mfutshane, ukusoda)

ISILUMKO

1. Qiniseka ukuba ujonga umthamo olinganisiweyotage kunye nolungiselelo lwetheminali phambi kocingo
2. Xa ufaka iintambo, qinisa isikrufu sebhloko yeterminal ngoluhlu lwetorque echaziweyo
3. Musa ukufaka izinto ezinokutsha kwindawo ezingqongileyo
4. Musa ukusebenzisa i-PLC kwindawo yokungcangcazela ngokuthe ngqo
5. Ngaphandle kwabasebenzi benkonzo yeengcali, Musa ukuqhaqha okanye ulungise okanye uguqule imveliso
6. Sebenzisa i-PLC kwimeko-bume ehlangabezana neenkcukacha ngokubanzi eziqulethwe kule datha.
7. Qinisekisa ukuba umthwalo wangaphandle awudluli umlinganiselo wemveliso yemveliso.
8. Xa ulahla i-PLC kunye nebhetri, yiphathe njengenkunkuma yamashishini.

Indawo yokusebenza

Ukufakela, jonga le miqathango ingezantsi

Hayi	Into	Inkcazo				Umgangatho
1	Ithuba elikwiNdawo.	0 ~ 55℃				–
2	Ubushushu bokugcina.	-25 ~ 70℃				–
3	Ukufuma kwendawo	I-5 ~ 95%RH, i-non-condensing				–
4	Ukugcinwa kokufuma	I-5 ~ 95%RH, i-non-condensing				–
5	Ukunyangwa kweVibration	Ukungcangcazela ngamaxesha athile			–	–
		Ukuphindaphinda	Ukukhawulezisa	Ampimfundo	Amaxesha	IEC 61131-2
		5≤f<8.4㎐	–	3.5mm	Amaxesha ali-10 kwicala ngalinye X AND Z
		8.4≤f≤150㎐	9.8㎨(1g)	–
		Ukungcangcazela okuqhubekayo
		Ukuphindaphinda	Ukuphindaphinda	Ampimfundo
		5≤f<8.4㎐	–	1.75mm
		8.4≤f≤150㎐	4.9㎨(0.5g)	–

Iinkcukacha zokusebenza

Le yinkcazo yoMsebenzi we-XGB. Ukufumana iinkcukacha ezithe vetshe, jonga kwincwadi ehambelanayo.

Into	Inkcazo
Indlela yokusebenza	Ukusebenza okuphindaphindayo, ukusebenza komjikelo osisigxina, Ukuphazamisa ukusebenza, ukuskena rhoqo kwexesha
Indlela yokulawula ye-I/O	Skena inkqubo yebhetshi ehambelanayo (indlela yokuhlaziya) Indlela ethe ngqo ngomyalelo
Isantya sokusebenza	Umyalelo osisiseko: 0.83㎲/inyathelo
Imemori yenkqubo umthamo	XBC:15Kstep, XEC: 200KB
Ukwandiswa slot Max	Okungundoqo + Ukwandiswa kwe-10 Slot (ukwandiswa kwendawo)
Imo yokusebenza	BALEKA, YIMISA, LUNGISA
Ukuzixilonga	Ukulibaziseka kokusebenza, inkumbulo engaqhelekanga, i-I/O engaqhelekanga
Izibuko lenkqubo	I-USB(1Ch), RS-232C(1Ch)
Indlela yokugcina idatha kwi ukusilela kwamandla	Ukubeka i-latch(ukugcina) indawo kwi-parameter esisiseko
Umsebenzi owakhelwe ngaphakathi	I-Cnet (RS-232C, RS-485), i-PID, i-Speed ​​counter counter, i-RTC

Igama lendawo kunye nobungakanani (mm)

Le yinxalenye engaphambili ye-CPU. Bhekisela kwigama ngalinye xa uqhuba inkqubo. Ngolwazi oluthe vetshe, jonga kwincwadi yomsebenzisi.

1. Ibhloko yoNxibelelwano olwakhelwe ngaphakathi
2. Ibhloko yokufaka iteminali
3. Imveliso ye-24V (Amandla angaphantsi, ayisetyenziswanga kwiyunithi yamandla / DC)
4. PADT Connect(USB, RS232)
5. Ukutshintsha kwediphu yemowudi ye-O/S
6. Imo yokufaka i-LED
7. Imo yemveliso ye-LED
8. Ukutshintsha kwediphu yemowudi ye-O/S
9. Ubume bokusebenza kwe-LED
10. Ibhloko yeterminal yamandla
11. Ibhlokhi yetheminali yemveliso

Ubungakanani(mm)

Imveliso	W	D	H
XB(E)C-DR(N)32H(/DC)	114	64	90
XB(E)C-DR(N)64H(/DC)	180	64	90

Isoftware yenkxaso esebenzayo

Kubumbeko lwesixokelelwano, oluguqulelo lulandelayo luyimfuneko.

1. Isoftware ye-XG5000: V3.61 okanye ngaphezulu

Izixhobo kunye neNgcaciso zeCable

Jonga ibhetri encanyathiselwe kwimveliso

1. Ikaliwe iVoltage/Yangoku: I-DC 3.0V/220mAh
2. Ixesha lewaranti: Iminyaka emi-3 (kwi-25 ℃, ubushushu obuqhelekileyo)
3. Ukusetyenziswa: Inkqubo / i-back-up yedatha, ukuqhuba i-RTC xa ukucima umbane
4. Inkcazo: I-Manganese dioxide lithium (φ20 X 3.2mm)

Jonga i-accessory (Oda intambo ukuba kuyimfuneko)

1. PMC-310S: I-RS-232 yokudibanisa (ukukhuphela) intambo.
2. I-USB-301A: Intambo ye-USB yokuqhagamshela(yokukhuphela).

Ukufakela / Ukususwa kweeModyuli

Apha kuchaza indlela yokufaka imveliso yokususa.

1. Kuhlohlwa imodyuli
   1. ukunciphisa i-Inshorensi yoLwandiso kwimveliso.
   2. Tyhala imveliso kwaye uyidibanise ngokuhambelana neHook yoLungiso lwemiphetho emine kunye neHook yoQhagamshelwano ezantsi.
   3. Emva koqhagamshelo, tyhala iHook yoLungiso kwaye uyilungise ngokupheleleyo.
2. Ukususa imodyuli
   1. Tyhila iHook yokususa, kwaye emva koko ufake imveliso ngezandla ezimbini. (Musa ukususa imveliso ngenkani)

Iintambo

Iingcingo zombane

1. Kwimeko apho utshintsho lwamandla lukhulu kunoluhlu olusemgangathweni, qhagamshela umthamo ongaguqukiyotage transformer
2. Qhagamshela amandla anengxolo encinci phakathi kweentambo okanye phakathi komhlaba. Kwimeko yengxolo eninzi, qhagamshela isiguquli sokwahlula okanye isihluzi sengxolo.
3. amandla ePLC, isixhobo se-I/O kunye nabanye oomatshini kufuneka bahlukane.
4. Sebenzisa umhlaba ozinikeleyo ukuba kunokwenzeka. Kwimeko yokusebenza komhlaba, sebenzisa iiklasi ezi-3 zomhlaba (ukumelana nomhlaba 100 Ω okanye ngaphantsi) kwaye Sebenzisa ngaphezulu kwe-2㎟ intambo yomhlaba. Ukuba umsebenzi ongaqhelekanga ufunyenwe ngokomhlaba, yahlula umhlaba

Iwaranti

• Ixesha lewaranti
  • Kwiinyanga ezili-18 emva komhla wemveliso.
• Umda weWaranti
  • Iwaranti yeenyanga ezili-18 iyafumaneka ngaphandle:

1. Iingxaki ezibangelwa yimeko engafanelekanga, indawo esingqongileyo, okanye unyango ngaphandle kwemiyalelo ye-LS ELECTRIC.
2. Iingxaki ezibangelwa zizixhobo zangaphandle
3. Iingxaki ezibangelwa kuhlengahlengiso okanye ukulungiswa ngokusekelwe kwingqiqo yomsebenzisi.
4. Iingxaki ezibangelwa kukusetyenziswa ngokungafanelekanga kwemveliso
5. Iingxaki ezibangelwa sisizathu esigqithise ulindelo oluvela kwinqanaba lesayensi kunye nethekhnoloji xa i-LS ELECTRIC ivelisa imveliso.
6. Iingxaki ezibangelwa yintlekele yemvelo

Utshintsho kwiinkcukacha

• Iimpawu zemveliso zinokutshintshwa ngaphandle kwesaziso ngenxa yophuhliso oluqhubekayo lwemveliso kunye nokuphuculwa.

I-LS ELECTRIC Co., Ltd

• www.ls-electric.com
• 10310000915 V4.4 (2022.9)
• I-imeyile: automation@ls-electric.com
• Ikomkhulu/iOfisi yaseSeoul
  • Umnxeba: 82-2-2034-4033,4888,4703
• LS ELECTRIC IOfisi yaseShanghai (eTshayina)
  • Umnxeba: 86-21-5237-9977
• I-LS ELECTRIC (Wuxi) Co., Ltd. (Wuxi, China)
  • Umnxeba: 86-510-6851-6666
• I-LS-ELECTRIC Vietnam Co., Ltd. (eHanoi, eVietnam)
  • Umnxeba: 84-93-631-4099
• I-LS ELECTRIC Middle East FZE (Dubai, UAE)
  • Umnxeba: 971-4-886-5360
• LS ELECTRIC Europe BV (Hoofddorf, Netherlands)
  • Umnxeba: 31-20-654-1424
• I-LS ELECTRIC Japan Co., Ltd. (eTokyo, eJapan)
  • Umnxeba: 81-3-6268-8241
• LS ELECTRIC America Inc. (Chicago, USA)
  • Umnxeba: 1-800-891-2941

Umzi-mveliso: 56, Samseong 4-gil, Mokcheon-eup, Dongnam-gu, Cheonan-si, Chungcheongnam-do, 31226, Korea

Amaxwebhu / Izibonelelo

I-LS XEC-DP32 / 64H isiLawuli esiQinisekileyo esiQinisekayo [pdf] Isikhokelo soFakelo XEC-DP32 64H Programmable Logic Controller, XEC-DP32 64H, Programmable Logic Controller, Logic Controller

Iimbekiselo

• Incwadi yokusebenzisa