wopet CL11 Cube Lite Automatic Cat Feeder
wopet CL11 Cube Lite Automatic Cat Feeder

PRODUCT SPECIFICATIONS

Model CL11
Capacity 4L
Meals 1-6 meals per day
Screen LCD
One port ion 10g / 0.35oz (8 port ions at most per meal)
Food size 2 – 12mm (dry food only)
Pet size Cat s and small/ medium-sized dogs
Battery-powered supply 3 x alkaline D batteries (not included)
DC-powered supply 5V / l A
Operating temperature -10°C – 55 °C I 14 °F – 13 1°F
Dimensions 18x18x20.4cm / 7.l x7.l x8.0in

Product Overview

Product Over View

FEEDER ASSEMBLY

Take out the bowl

  • Take the bowl out and lift the hopper upwards, take out the Type-C charging cable, desiccant, manual, etc
    Feeder Assembly

Load in desiccant

  • Open the desiccant cap, put in the desiccant bag, and then close the cap.
    Load in desiccant

Insert batteries or power cable

  • Open the battery cover ① upward according to the indicated position, put in 3D-type batteries. Or, to use a DC power source, insert the Type-C power cable ②put the cable into the cable slot, and finally close the battery cover.

Note: The machine will automatically reset after 7 days of a power outage and all the data will be cleared.

Insert batteries or power cable

Install the bowl

  • Install the bowl ③ into the base ④ in the direction of the arrow as shown in the figure below.
    Install the bowl

Install the hopper

  • Install the hopper into the feeder base from top to bottom according to the arrow shown in figure (1)(2).
    Install the hopper

Install the lid

  • First tilt the cover into the slot, as shown in (3), and then press “lock” to close the cover into place, as shown in (4).
    Install the lid

Clean the hopper

  • Fix the base of the machine, lift the tank upward and remove from the base as shown in (5)(6).
    Clean the hopper

CONTROL PANEL

Note: When powered by batteries, the screen turns off after about 10 seconds.
Control Panel

Buttons and Functions

Button Description Instructions
Icon Unlock/ Lock/Save
  1. In locked state, press button to unlock, the screen will display ‘l. indicating the unlocked state.
  2. Auto-Locks if idle for 1 minute in locked state; screen off (screen tunns off).
  3. Save current settings.

Note: Screen turns off on battery power.

Icon Manual Feed In unlocked state, press to release one portion.
Icon Return In unlocked state, press to return.
Icon Settings In unlocked state, press to set up alarm –> Meal Plan –> portions release, and circles back.

Press to return at any point during setup.

Icon Reset Hold both buttons for 3s until the red light turns on to reset to factory settings.
Icon U p / Dow n Quick Meal Setting. In un ‘locked state, set Meal Plan -> Portions.

SETTINGS

Steps for setting up device

Step 1- Set Up Alarm

Press Icon to unlock the panel.

Set Hour

Press Icon to set up the current time.” 12 “on the hour blinks; press or hold  Icon or Icon to go up or down.
Settings

Set Minute

After setting hour, press Iconto set the minutes, press or hold Icon or Iconto go up or down.
Settings

AM/PM Settings

After setting hour/minute, press Iconor Icon to choose AM/PM, then press Icon again to save current time and proceed to next step.
Settings

Set Up Meal Plans and Portions

After the above settings, press Iconor Icon to enter meal plan scheduling and portion setting.

Press IconorIcon to set up the time for meal 1-6, the corresponding meal number will blink.
Set Up Meal Plans and Portions

Press Iconand the” 12″ on hour will blink. Press or hold Icon or Icon to go up or down.
Set Up Meal Plans and Portions

Press Iconand the “00” at minite flashes, press or hold IconorIcon to go up or down.
Set Up Meal Plans and Portions

After hrs/mins settings, AM/PM flashes, press Icon or Iconto set AM/PM, then press Iconagain to save the alarm and enter the next step.
Set Up Meal Plans and Portions

After setting up meal schedules, press @Icon, P – : 0 0 appears.
Set Up Meal Plans and Portions

Press Icon or Icon to set the meals (1-6 meal); and press Iconto save the current settings and go to the next schedule.

Note:

  1. Press Iconto save during setup or  Icon to return.
  2. To remove meal plans, go to the specific plan, and set portion to P – : 0 0 ..

FAQS

Q: Why don’t the feeder’s control panel buttons work?
A: Ensure it’s not locked. Press the “lock” button to unlock for use.

Q: Why is food dispensed unevenly?
A: Initially, portions may vary. It normalizes from the third dispensing.
Q: How to prevent food jams?

  1. Don’t compress food.
  2. Use food within size limit (2-12mm).
  3. Clean regularly to avoid clumps.

Q: What is the battery life on battery mode?

  1. Up to 180 days (Reference only)
  2. Requires 3 new, same-spec batteries.
  3. Battery life varies with temperature.
  4. Batteries as a backup when using power.

Q: What to do if pressing the  Icon button does not release food?

  1.  Check if there is still food left in the hopper.
  2. Ensure the outlet isn’t blocked.
  3. Food size should not exceed limit.

Q: What to do if I only set one meal?
A: Confirm Time/Meal/Portion and press Iconto complete/save all settings.

Q: Quick return to main page?
A: Press Icon until the screen stops changing.

Q: How to cancel or view a specific meal plan?

  1. In unlocked mode, press Icon or Icon to go to “1-6” settings
  2. Select meal and press Iconto skip time to view portions.
  3. Reset P – : 0 1-P – : 0 8 to P – : 0 0 by pressing Icon or Iconto cancel the meal plan.

Q: Can it be used outdoors?
A: Recommended for indoor use to protect from rain and moisture.

FCC WARNINGS

  • Changes or modifications to this unit are not expressly approved.
  • Non-compliance could void the user’s authority to operate the equipment.

Notes:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

  • Reorient or relocate the receiving antenna.
  • Increase the distance between the equipment and receiver.
  • Connect the equipment into an outlet on a different circuit than the one the receiver is currently connected.
  • Consult the dealer or an experienced radio/TV technician for help. Shielded interface cables must be used with the equipment in order to comply with the limits for a digital device pursuant to Sub part B of Part 15 of FCC Rules. Specifications and designs are subject to change without any notice or obligation on the part of the manufacturer.

Ask Us A Question

  1. Find your order
    Ask Us A Question
  2. Click “View order details”
    Ask Us A Question
  3. Click the Seller name
    Ask Us A Question
    Click “Ask a question”
    Ask Us A Question
  • Complimentary parts, replacements, consumable products are not covered by the 2-year warranty.
  • Manufactures’ warranties may not apply in all cases, depending on factors such as use of the product, where the product was purchased, or who you purchase the product from.
  • Please review the warranty carefully, and contact the manufacture if you have any questions.

Warranty Information

  • If you have any problems when using our products, please send us an email at support@wopet.com
  • 30 days free Return & Replacement
  • Standard Warranty: 1-Year product Warranty 2-Year Warranty Application: Please scan the QR code to finish the registration form on our official website within 30 days after you received the items.
    QR Code

Logo

Documents / Resources

wopet CL11 Cube Lite Automatic Cat Feeder [pdf] User Manual
CL11, CL11 Cube Lite Automatic Cat Feeder, Cube Lite Automatic Cat Feeder, Automatic Cat Feeder, Cat Feeder, Feeder

References

Leave a comment

Your email address will not be published. Required fields are marked *