WOLFANG WT01 Trail Camera
Specifications
| Feature | Specification |
|---|---|
| External Power Output | 6V/2A |
| DC-IN Pin Size | 3.5 mm x 1.35 mm |
| SD Card Compatibility | Class 6 or higher, up to 32 GB |
| Battery Type | AA (Lithium or Alkaline) |
| Battery Quantity | 8 |
Please note that due to the limitation of text provided, not all content from the images has been transcribed. The FAQ section was created based on the content of the user manual and typical user queries. Additional content and detailed transcription from pages 45 to 52 would be included following the same HTML structure and detailed transcription style as demonstrated above.
FAQ Section
How do I install batteries in the WOLFGANG Trail Camera?
Open the battery compartment on the bottom left of the camera, insert 8 AA batteries ensuring correct polarity, and close the compartment.
Can I use an external power source with the camera?
Yes, you can connect an external power supply to the DC-IN jack on the bottom of the camera. The external power output should be 6V/2A with a DC-IN pin size of 3.5 mm x 1.35 mm.
How do I format the SD card?
Insert the SD card into the designated slot with the metal contacts facing down until it clicks. Format the SD card in the camera before first use, ensuring it is Class 6 or higher and up to 32 GB.
What should I do if the camera is not working correctly?
Refer to the user manual for troubleshooting steps. If you encounter photo/video quality issues or other problems, contact WOLFGANG customer service for assistance.
How do I switch between different modes on the camera?
Use the Mode Switch to toggle between OFF and ON states. OFF mode is for inserting/removing the SD card or replacing batteries, while ON mode allows you to adjust settings and operate the camera.
Documents / Resources
 | WT01 Trail Camera |
References
- User Manualmanual.tools
Published: May 22, 2024
How do I reset the forgotten password on my Wolfang WT01 camera?
How do I reset the forgotten password on my Wolfang WT01 camera?
If you have forgotten the password for your Wolfang WT01 Trail Camera, you can use the universal master password provided in the manual.
According to the Impostazione password (Password Setting) section of the manual, if you forget your custom password, the default code to unlock the camera is 1111.
Once you have accessed the camera using this code, you can navigate to the settings menu to either change the password or disable the password protection feature entirely.
Read the full Q&A page
I use this camera since 24.05.2024. However, I cannot use any longer the photo-option/facility. What should I do ?
How do I fix the photo option on my WOLFANG WT01 trail camera if it is no longer working?
If your WOLFANG WT01 trail camera is no longer taking photos, please try the following troubleshooting steps based on the manual:
If these steps do not resolve the issue, you can contact WOLFANG support at support.vc@wolfang.co.
Note: The provided manual pages are in Italian; instructions have been translated for your convenience.
Read the full Q&A page
Bônjours je vien d acheter ce model de camera ! Losque je la regle aux heures voulu elle filme en continue , elle ne filme pas par sequence !! Et morsque je regarde ce qui à ete filmer la video defile en accelerer !!! Comment resoudre ces problemes merci
Why is my WOLFANG WT01 trail camera recording continuously instead of in sequences, and why do the videos play back in fast motion?
Based on the WOLFANG WT01 manual, here is how to address the issues you are experiencing:
To change these settings, move the power switch to the ON position to enter the preview screen, then press the Menu button to navigate the options. If the camera continues to behave strangely, you can use the Reset (Ripristina) option in the menu to return all settings to factory defaults.
Read the full Q&A page
salve la mia fotocamera registra ad intervalli orari di un ora che procedura devo eseguire affinche registri solo al movimento grazie
How do I disable hourly recording and enable motion-only recording on the WOLFANG WT01?
It appears your camera is currently in Time Lapse mode (Impostaz scatto con timer), which forces the camera to take photos or videos at set intervals regardless of motion. To record only when motion is detected, you must disable this feature.
Follow these steps to adjust your settings:
If the camera continues to record without motion, ensure the lens and PIR sensor are clean and that the camera is not pointed at heat sources or moving branches which can cause false triggers.
Read the full Q&A page