WipCOOL C30S Steam Cleaning Machine
Notice for Use
Thank you for buying WIPCOOL C
- Series A/C cleaning pump, we are dedicated to providing you with high-quality products.
Please check if your ordered product is in good shipment condition, with the correct accessories, any damage during transportation, please contact us or the local distributors in time if you find any problems.
This manual gives instructions on the correct operation, it’s important that you follow this instruction carefully.
If there is any change in the product (including the specification), we won’t inform any more.
WARNING
To ensure the product long-time stable working, please read this manual carefully before your installation, transportation, repair or maintenance, in order to fully understand the safety problems, the technical data and operating methods of the pump and other related notices points.
Caution
Note the following points during use
- Make sure inlet hose is in the bucket, start the machine in “COOL” mode to avoid machine in dry running and get in dry burning protection. “STEAM” MODE must be used with clean water.
- The maximum power of this machine is 3300W, please use it under the range of power supply, if the general domestic power line cannot bear and trip, please use small steam or 2200W “HOT” water function, do not use large steam and 3300W “HOT” water function, so as not to bum out the circuit.
- Strong acid detergent is not allowed. We are unable to accept any liability in case of blockage or breakage for nonconforming usage.
- Spray gun soaked in the water is not allowed, to avoid any internal parts damaged.
- 02mm short and long spray nozzles are just used on steammode, 200 spinning gun should be used in HOT and COOL mode.STEAM mode is not allowed.
- Do not touch directly by hand as the internal heater and steam nozzle temperature is very high after using steam and hot water function.
- Please check if any blockage in Nozzle vent hole if poor steam. white dirt will be created after long time using.
- Direction can be adjusted by left or right turning, water shape (columnar or mist can be adjusted by nozzle switching)
- It will take about 25s to create steam when you start “STEAM” MODE.it is normal when the water reserved in the pipeline automatically drained before the steam is out.
- Please use “COOL” mode to drain out the inside water before you shut down this machine. “STEAM “or “HOT” mode is forbidden.
- ” High Temp” warning will light on the LCD display and indicate over- temperature. Please check if the inlet filter’s blockage caused the poor water suction or shortage. Clean the filter and Machine will resume working after 20minutes cooling.
- If the machine cannot do sell-priming,please fulfill with water into pipe and pump until outlet overflows, then it will resume normal working.
- Please stop working immediately once the machine gets wet, plug off.
Dry off and let it dry naturally before you re- start it.
- Don’t spray to any people, pets and machine itself to avoid accident during operation.
Attention in “HOT” mode
- Corrosive detergents are not allowed. We are unable to accept any liability if it caused corrosion or damage.
- The “HOT “mode can be adjusted to 3options, high, medium and low water pressure, the temperature can be adjusted to 3options, High temp(3300W), Medium temp(2200W), and Low temp(1100W).
- You can adjust the water temperature and pressure according your different needs, the normal temperature water can be directly heated to 60 °C, and the circulating hot water can reach 100 °C to achieve better cleaning.
- Be sure to clean the internal line of the machine with clean water after each use.
Attention in “STEAM” mode
- Make sure inlet hose is in the bucket with clean water, start the machine with “COOL “mode firstly to avoid machine in dry running and get in dry-burning.
- Be sure used with clean water, detergent or dirty water is not allowed.
- Adult operate only
- Inlet water temperature should be no more than 50°C.
- Do not block the steam ejection vent during operation, to avoid the high inner pressure, and cause the serious damage.
- There will be a preheating procedure when start the “STEAM” mode, so Water spillage is normal.
- Clean inlet filter before use to avoid blockage.
- There will be 1 second’s cool water extension, be careful of high pressure and high temperature water during this extension.
- Please choose “COOL” mode to drain off the inside water after use. It will cause “HIGH TEMP” warning if choose “HOT” or “STEAM” for drainage.
- Machine will switch to “COOL” mode automatically if “High Temp” light on the LCD and enclosed with voice alarm, “STEAM” mode will resume working when the temperature is down.
Product Instruction
Product overview
WIPCOOL C serious A/C cleaning machine is special design for domestic Air Conditioner and small refrigeration equipment cleaning. Built-in permanent magnet motor powered water pump.the product features as below:
- High temperature and high-pressure steam, pure physical sterilization and disinfection
- Multiple stage water temperature to meet the requirements of different working conditions
- LCD touch display, voice reminder, more humanized operation
- Intelligent spray gun, one-touch operation during operation, convenient function selection
- Steam, hot water and cold-water flow in and out of the same pipeline, simple maintenance
- Super ozone sterilization, Prevent bacteria
- Drum pump body structure, freely retractable inlet and outlet pipes
Key operation instruction
Remark: The steam moisture can not be adjusted remotely by multi-functional spray gun, only by pressing “temperature / moisture” on the control panel.
Muti-function Spray Gun
The spray gun reached the muti-function of water pressure adjustment, cleaning mode switching, ON/STOP through emote action. Turn on light when in dark place.
different functions under CLEANING/PAUSE status.
- when machine is in “PAUSE” status, press the “FUNCTION” key to choose your cleaning mode” COOL”,” HOT”, ” STEAM”, ” DISINFECT”, ” PULSE”
- when machine is on operation in “COOL”,” HOT” mode, press the “FUNCTION” key to adjust water pressure.
- when machine is on operation in “STEAM” mode, press the “FUNCTION” key to adjust steam pressure.
Application&Range
C Serious STEAM A/C cleaning machine is special design for indoor or outdoor units.
But it is also can be used in household appliances such as lampblack machine, refrigerator, washing machine, water heater, water dispenser, etc.
The machine applied the instant high-temperature working principle. Realize the dis- assembly free cleaning for air conditioner and fume hood. Clean the harmful substances such as scale and rust in drinking water machine, water heater and other household appliances through circulation washing. It has super strong ozone sterilization technology, which can completely sterilize the areas where are easy to breed, such as drinking machine, washing machine, refrigerator and so on. the bactericidal rate is 99.9%.
Technical parameter
Measurement
Product Configuration
Operation procedure
Inspection before Operation
Please check any damage of products and accessories, any blockage of filter and nozzle, any abnormal for assemble or connection before your operation.
Correct usage
- put the inlet pipe into the bucket with clean water inside.
As shown on the below picture.
Make sure inlet hose is in the bucket, start the machine in “COOL” mode to avoid machine in dry running and get in dry buming protection. “STEAM” MODE must be used with clean water. - Plug in correct AC power(230V/16A),then make the leakage testing. Start the
operation after LCD display lights and Voice prompts - Put the spray nozzle towards the bucket, then select your cleaning function mode (COOL, HOT, STEAM, DISINFECT, PULSE) through touching keys on LCD or Muti-function Spray Gun, adjust the pressure and temperature according your requirement.
- 220°spinning gun should be just used in “HOT” and “COOL” mode.
Direction can be adjusted by left or right turning, water shape (columnar or list) can nozzle switching be adjusted by
¢ 2mm spray nozzle is just used on “STEAM” function only. - Please switch to “COOL” mode and last for 10seconds after use “STEAM” or “HOT” mode, to cool down the inner heater quickly.
- 140°C-150°C is in big “STEAM” mode, 130°C-140°C is in small “STEAM” mode.
- Press “RESET” key on the PLUG for short-time shutdown.
Troubleshooting
Attention: if “high temp” warning occur frequently, please contact with manufacurer and solve the problem timely.
Documents / Resources
 |
WipCOOL C30S Steam Cleaning Machine [pdf] Instruction Manual C30S_manual_Wipcool.pdf, C30S_Wipcool_manual, C30S Steam Cleaning Machine, C30S, Steam Cleaning Machine, Cleaning Machine, Machine |