WINNERCOM CE NFC Touch Door Handle
Introduction
- Door handle Module (DHS)
- NFC & Capacitive Touch
- Pocket Light LED
- Hi-Speed CAN
The door handle module for Automotive has a NFC Reader and lock/Unlock 2Channel Capacitive touch Sensor function.
This module is installed inside of the door handle covers and will be attached to the outside door panel.
This module is communicated with CAN network which enables to connect to the car network to send the signal of lock and unlock of door and Pocket light LED On/Off control.
It receives DC power from car battery at all time.
NFC DHS Design(BOM) & Application
CE – NFC Touch Door Handle
|
ITEMS |
SPECIFICATION |
|
Size |
125 x 18 x 20 mm (Length x Width x Height) |
| Color |
Black |
|
Weight |
53g +/- 2.2% |
| Waterproof |
Polyurethane full potting inside of module. Protective of humidity ,vibration, waterproof. |
|
Material |
Case : PA6+GF15% , ABS / PRESS : SPTE(Tin-Plating) / PCB : FR-4, 4Layer / |
| NO | Lev | SUB | ||
| 1 | 1 | CASE UPPER | A6+GF15% | |
| 2 | 2 | ASELO1NER | PC | |
| 3 | 1 | PCBASSY | TBD | FR-4 |
| 4 | 1 | FPCB | TBD | |
| 5 | 2 | FOAM PAO LED | EPDM | |
| 6 | 2 | CABLEASSY | AVSS0.3SQ | |
| 7 | 1 | FOAMPADA | POM | |
| 8 | 1 | FOAMPAOB | POM | |
| 9 | 1 | ANT POTTING | UE-917 A,B | |
| 10 | 1 | TAPE | – | PVC |
Attentions
- Please always mount the Door handle Module before power on the device to avoid circuit damage
- Before power on the Module, check the power supply (Fig. 1)
- Module Input Power connect to the connector(Fig. 1)
– Type : Spin Connector Sealed+’
– Maker & Part No.:. HKC0S-12737 SP Male Connector(Blue)
|
Pin#.⤾ |
Name- | Description | In/ Out | Wire Color |
I/O Level |
|
1⤾ |
V Bat(+Vcc)⤾ | Power Supply⤾ | Power⤾ | RED⤾ | Battery +⤾ |
| 2⤾ | L _CAN(L)⤾ | CAN Low Signal⤾ | I/O⤾ | GREEN⤾ |
2.5±TBD V⤾ |
|
3⤾ |
TOUCH⤾ | LOCK/ UNLOCK⤾ | I/O⤾ | GRAY⤾ | LOCK/UN LOCK⤾ |
| 4⤾ | L_CAN(H)⤾ | CAN High Signal.:i | lfO., | BLUE⤾ |
2.5+TBD V⤾ |
|
5⤾ |
⤾ | ⤾ | ⤾ | ⤾ | ⤾ |
| 6⤾ | GND | Electric Ground⤾ | Power⤾ | BLACK⤾ |
Gnd⤾ |
CAN(HI)CAN(LO)
Specifications
|
NFC Touch Data |
|
| Frequency Range | 13.56MHz for NFC |
| Operating Voltage | 9.0 ~ 16.0 [Vdc], Typical 12.0 [Vdc] |
| Current | Max 400mA @ Operation Mode |
| Operating Temp. | -30℃ ~ 75℃ |
| Storage Temp. | -40℃ ~ 85℃ |
| Symbol⎓ | DC, IEC 60417-5031 (2002-10) |
User Information and Instructions
FCC Part 15 Compliance information.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- This product is compliant with the essential requirements and other relevant provisions of the Directive 2014/53/EU.
- This product can be used in which EU members, in accordance with ArticleS10(10).
Manufacturer information
|
Manufacturer name |
WINNERCOM Co., Ltd. |
|
Address, City: |
HUMAX Village, 216, Hwangsaeul-ro, Bundang-Gu, Seongnam-si, Gyeonggi-do, South KOREA 13595 |
| Product name (type): |
Vehicle active antenna & Touch door |
Documents / Resources
 |
WINNERCOM CE NFC Touch Door Handle [pdf] User Manual CE, 2AU37CE, CE NFC, Touch Door Handle, CE NFC Touch Door Handle, NFC Touch Door Handle, Touch Door Handle, Door Handle, Handle |
