DR5018 AP Controller
Product Information
Specifications:
- Product Name: Wallystech AP Controller
- Type: Hardware-Based Wired and Wireless Device Network
Controller - Website: www.wallystech.com
- Date: 2025-1-20
Product Usage Instructions
Getting Started
1. Introduction:
This section provides an overview of the Wallys AP Controller
software and describes the initial steps required to start using
the service.
Wallys AP Controller Login:
To log in to the Wallys AP Controller, follow these steps:
From a web browser, go to 192.168.1.1.
Default User Name: admin
Default Password: 123456
Capture APs:
To add devices (Capture APs) and manage them, access the Device
Management View.
Adding Devices:
When adding devices, you may receive warning and successful
messages to indicate the process status.
Firmware Upgrade & Filtering:
You can upgrade firmware by clicking the Firmware Upgrade Button
and filter the device view as needed.
Change Default Password:
To change the default password, follow the instructions
provided. Upon successful password change, the webpage will
automatically redirect to the Home page.
Change AP Controller IP Address:
Change the default IP address of the AP Controller. After
applying the new IP address, the webpage will auto redirect to the
Home page.
Set Up Multiple IP Addresses Across Different Network
Segments:
Refer to the function diagram for successful setup of multiple
IP addresses.
System Upgrade and User Manage:
You can perform system upgrades and manage users through the
provided functionalities.
Configuration
2. Batch Configuration:
This section details configuring access point settings.
The Dashboard:
The dashboard provides an overview of device status and recent
activity information.
Configure WiFi:
You can configure WiFi settings in batch for efficient
setup.
Upgrading Device Firmware:
To upgrade device firmware:
– View device information by clicking on the device name
link.
– Click the upgrade icon when new firmware is available.
– Ensure to save configuration settings if needed.
– Follow the firmware upgrading process until successful
completion.
FAQs
Q: How do I reset the device to factory settings?
A: To reset the device to factory settings, locate the reset
button on the device and hold it down for at least 10 seconds until
the device restarts.
Q: Can I access the AP Controller remotely?
A: Yes, you can access the AP Controller remotely by configuring
port forwarding on your router and using a public IP address.
Wallystech AP Controller User Manual
www.wallystech.com
Date:2025-1-20
https://www.wallystech.com/
User Manual
Wallystech AP Controller
Hardware-Based Wired and Wireless Device Network Controller
https://www.wallystech.com/
Contents
Section
Getting Started
1 Introduction
Wallys AP Controller Login Capture APs Firmware Upgrade Button Filtering the Device View Change Default Password Change AP Controller IP Address Set Up Multiple IP Addresses Across Different Network Segments System Upgrade and User Manage
Section
Configuration
2 Batch Configuration
Upgrading Device Firmware Configure WiFi Upgrading Device Firmware Deleting Offline Devices Update Equipment Notes Importing Witelist Execute Command
https://www.wallystech.com/
Section
Getting Started
This section provides an overview of the Wallys AP Controller software and describes the initial steps required to start using the service.
https://www.wallystech.com/
Chapter 1 | Introduction Wallys AP Controller Login
The Wallys AP Controller is a hardware-based network solution tailored for efficiently configuring multiple access points through a web browser interface. With its robust scalability, it supports the management of unlimited networks and devices. By integrating network management and wireless controller functionalities, it allows Wallystech access points (APs) to seamlessly connect and operate as a unified network. The following devices are supported by Wallys AP Controller: u Wallys APs: DR5018,DR5018S,DR6018,DR6018S,DR6018C,DR4019
Wallys AP Controller Login
From a web browser, go to 192.168.1.1 to login. Default User Name:admin Default Password:123456
https://www.wallystech.com/
Chapter 1 | Introduction
Capture APs
Adding Devices(Capture APs)
Device Management View
https://www.wallystech.com/
Chapter 1 | Introduction
Adding Devices
Adding Devices Warning Message
Adding Devices Successful Message
https://www.wallystech.com/
Chapter 1 | Introduction
Firmware Upgrade & Filtering
Firmware Upgrade Button
Filtering the Device View
https://www.wallystech.com/
Chapter 1 | Introduction
Change Default Password
Change Default Password
Change Default Password Successful
After New Password Applied,the webpage will auto turn to Home page.
https://www.wallystech.com/
Chapter 1 | Introduction
Change AP Controller IP Address
Change Default AP Controller IP Address
Change Default IP Address Successful
After New IP address Applied,the webpage will auto turn to Home page.
https://www.wallystech.com/
Chapter 1 | Introduction
Set Up Multiple IP Addresses Across Different Network Segments
Function Diagram
Set Up Multiple IP Address Successful
https://www.wallystech.com/
Chapter 1 | Introduction
System Upgrade
System Upgrade
User Manage
https://www.wallystech.com/
Section Configuration
This section provides details on configuring access point settings.
https://www.wallystech.com/
Chapter 2 | Configuration
The Dashboard
The Dashboard
The dashboard provides an overview of status for configured devices, recent activity information overview.
Monitor
https://www.wallystech.com/
Chapter 2 | Configuration
Configure WiFi
Configure WiFi in Batch
Configure WiFi
https://www.wallystech.com/
Chapter 2 | Configuration
Upgrading Device Firmware
Viewing Device Information
Click a device name link in the Name column to access the detailed device information.
Upgrading Device Firmware
Click the upgrade icon in the FW column when new firmware is available for a device.
Note:check the box “save configuration”hitftpnse:/e/wdwtwo.wkaelleypstetchhe.cocmon/ figuration remain.
Chapter 2 | Configuration
Upgrading Device Firmware
New FW Upgrading process
Upgrading Device Firmware Successful
Active: running-upgrading-flashing-upgrade success-running
https://www.wallystech.com/
Chapter 2 | Configuration
Deleting Offline Devices
Deleting Offline Devices
Deleting Offline Devices Successful
https://www.wallystech.com/
Chapter 2 | Configuration
Update Equipment Notes
Update Equipment Notes
Equipment Notes for Group Management
https://www.wallystech.com/
Chapter 2 | Configuration
Importing Witelist
Importing Witelist
Witelist upload for your AP Devices
https://www.wallystech.com/
Chapter 2 | Configuration
Execute Command
Execute Command
Input Command(eg.as picture below)
https://www.wallystech.com/
Documents / Resources
 |
Wallys DR5018 AP Controller [pdf] User Manual DR5018, DR5018S, DR6018, DR6018S, DR6018C, DR4019, DR5018 AP Controller, DR5018, AP Controller |