WAINLUX K10 Cutlabx PC Software Engraving Parameter Table Instructions
NOTE
- When engraving white ceramics, white ceramic tiles, and transparent glass, you need to use laser engraving paper (black).
- The results would be different in even same material with different finishing or different colors, so you need to adjust the Speed and Power rate based on different objects. Also, please adjust the focal length to be the best, make the focal spot to be the smallest. 3.
- When engraving low-ignition point materials, it is recommended to increase the engraving Speed, otherwise there is a risk of fire. 4.
- When the laser engraving machine is working, the operator must pay close attention and must not leave the machine midway to prevent the engraving material from catching fire.
K10 Cutlabx PC Software Engraving Parameter Table
| Material | Picture | 3W |
| MDF |  |
Image Mode: Monochrome Monochrome Interval (mm): 0.05 Speed (mm/m): 3000mm/min Power (%) : 100 |
| Basswood Plywood |  |
Image Mode: Monochrome Interval (mm): 0.05 Speed (mm/m): 2000mm/min Power (%) : 100 |
| Birch Plywood |  |
Image Mode: Monochrome Interval (mm): 0.05 Speed (mm/m): 2000mm/min Power (%) : 100 |
| Pine Board |  |
Image Mode: Monochrome Interval (mm): 0.05 Speed (mm/m): 3000mm/min Power (%) : 100 |
| Paulownia Wood Board |  |
Image Mode: Monochrome Interval (mm): 0.05 Speed (mm/m): 3000mm/min Power (%) : 100 |
| Bamboo |  |
Image Mode: Monochrome Interval (mm): 0.05 Speed (mm/m): 1500mm/min Power (%) : 100 |
| Paperboard (Cardboard Box) |  |
Image Mode: Monochrome Interval (mm): 0.05 Speed (mm/m): 3000mm/min Power (%) : 100 |
| A4 Paper (Not White) |  |
Image Mode: Monochrome Interval (mm): 0.1 Speed (mm/m): 3000mm/min Power (%) :65 |
| Scraping Paper |  |
Image Mode: Monochrome Interval (mm): 0.05 Speed (mm/m): 3000mm/min Power (%) :30 |
| Kraft Paper 250g |  |
Image Mode: Monochrome Interval (mm): 0.05 Speed (mm/m): 2500mm/min Power (%) : 100 |
| Leather |  |
Image Mode: Monochrome Interval (mm): 0.1 Speed (mm/m): 3000mm/min Power (%) : 100 |
| Black Acrylic |  |
Image Mode: Monochrome Interval (mm): 0.05 Speed (mm/m): 1500mm/min Power (%) : 100 |
| Cobblestone (Dark-Colored) |  |
X |
| Black Slate |  |
Image Mode: Monochrome Interval (mm): 0.1 Speed (mm/m): 1500mm/min Power (%) : 100 |
| Ceramics (Need Blackened) |  |
Image Mode: Monochrome Interval (mm): 0.05 Speed (mm/m): 100mm/min Power (%) : 100 |
| Glass (Need Blackened) |  |
Image Mode: Monochrome Interval (mm): 0.05 Speed (mm/m): 200mm/min Power (%) : 100 |
| Coated Metal |  |
Image Mode: Monochrome Interval (mm): 0.05 Speed (mm/m): 500mm/min Power (%) : 100 |
| Plated Metal |  |
X |
| Stainless Steel |  |
X |
| Rubber |  |
Image Mode: Monochrome interval (mm): 0.05 Speed (mm/m): 1500mm/min Power (%) : 100 |
| PVC |  |
Image Mode: Monochrome Interval (mm): 0.05 Speed (mm/m): 3000mm/min Power (%) : 40 |
| Silica Gel |  |
Image Mode: Monochrome Interval (mm): 0.05 Speed (mm/m): 800mm/min Power (%) : 100 |
| Ceramic Tile (Need Blackened) |  |
Image Mode: Monochrome Interval (mm): 0.05 Speed (mm/m): 200mm/min Power (%) : 100 |
| Gold |  |
X |
| Silver |  |
X |
| Copper |  |
X |
| Pure Aluminum |  |
X |
Documents / Resources
 |
WAINLUX K10 Cutlabx PC Software Engraving Parameter Table [pdf] Instructions K10 Cutlabx PC Software Engraving Parameter Table, K10, Cutlabx PC Software Engraving Parameter Table, Software Engraving Parameter Table, Engraving Parameter Table, Parameter Table |
