VIMAI V39 Wireless Microphone User Manual

VIMAI-LOGOVIMAI V39 Wireless Microphone

VIMAI-V39-Wireless-Microphone-01

Package Contents

VIMAI-V39-Wireless-Microphone  (2)

Specification Parameters

Wireless Frequency Range 2402-2480MHz
Modulation GFSK
Audio Frequency Range 20Hz-20KHz
Audio Delay s2SMS
Transmission Power s10d8m
Operating Current s30MA
Signal-to-No ise Ratio >80d8
Microphone Type Omnidirectional
Built-in Battery TX Transmi tter-70mAh, Charging Case-400mAh
Charg ing Input TX Transmi tter-OC5V/65mA; Charging Case-DC5V/310mA
Power Management TX Transmi tter auto-shutdown after disconnected in 3 minutes
Charging Time TX Transmi tter ~1.5h, Charging Case-2h
Usage Time TX Transmitter~6h;

Charging Case charges 2TX twice

Transmission Distance 50m (Barrier free)
Operating Temperature O’C to 55 ‘C
Storage Temperature -20 “C to +55 -C
Size l 69*W60 “‘H36mm
Total Weight 75g

Functions of the Charging Case

VIMAI-V39-Wireless-Microphone  (4)Power Indicator – When TX is put into the charging case, the indicator light displays case battery level for 10 seconds.

Power Indicator Red light
flashing fastly
Red light
flashing slowly
Blue light
remains on
Green light
remains on
Battery Level <13% 13%-35% 36%-74% 75%-100%
  1. Place TX and RX correctly into their designated slots in the charging case.
  2. Please have charging cased charged immediately when red light flashing fatly Red light remains on when charging and turns off when fully charged. Please Unplug charging cable timely.
  3. TX will automatically powers off when placed into the charging case. Indicator will show case battery level and then the charging case will charge TX and green light flashes after 10S. Green Light will turn off when fully charged.

TX Transmitter Features

VIMAI-V39-Wireless-Microphone  (5)

  1. MFB: Press and hold for 3 seconds to power on/off. Single click to switch noise cancellation modes. Hi-Fi mode is on by default with solid green light; Al noise cancellation is on with solid yellow light; DSP noise cancellation is on with solid blue light. Double click to turn on mute and unmute (Red light is on when muted).
  2. Power-on Pairing Mode: Red and blue lights flashes alternately when power on; green light remains on when connected successfully.
  3. Low Battery & Charging: Red light flashes when battery is low (charge TX immediately); red light remains on when charging; red light turns off when fully charged.
  4. Clip Placement: Fix the transmitter within 20cm of the sound source (e.g., collar).

RX Receiver Function Description

  1. Connect the RX to phone, and it will automatically power on and paired.
  2. Some Android phones requires to turn on the OTG function manually for external plug-in device.

VIMAI-V39-Wireless-Microphone  (7)

Usage Steps

  1. Take out both TX and RX from the charging case. The TX will automatically power on and enter pairing mode with alternating red and blue slow flashing lights.
  2. Connect the RX to phone. The TX and RX will automatically pair, indicated by a solid green light upon successful connection. If no connection is established within 3 minutes, the TX will automatically power off.
  3. Recommend to fix the TX within 20cm of the sound-emitting area (e.g., collar) for optimal performance.
  4. It supports to charge your mobile phone via the Type-C port on the RX When phone battery is low. Single-click the TX MFB to switch Noise Canceling mode. Double-click the TX MFB to enter/exit mute. The ports on both TX and RX are exclusively for charging purposes.

Manual Pairing Method
If TX and RX fail to pair automatically, follow these steps for manual pairing:

  1. Press the MFB five times Within 10 seconds of powering on the TX, (the indicator light will flash red and blue alternately in pairing mode).
  2. Press the manual pairing button on the RX five times Within 10 seconds of connecting the RX to a phone, (the green indicator will flash fatly, in pairing mode).
  3. Both TX and RX indicator lights remain on green when pairing successfully

Product Usage Guidelines

  1. As a precision electronic device, avoid water exposure or severe impacts. If liquid ingress occurs, power off immediately, drain residual moisture, and seek professional assistance.
  2. For prolonged storage, recharge the battery every two months to maintain optimal performance.
  3. Never expose internal batteries to direct sunlight, open flames, or extreme heat environments.
  4. Use only original cables provided with the product or those recommended by authorized dealers/manufacturers. Third-party  cables may compromise functionality due to inconsistent technical standards.
  5. Always select chargers certified with China Compulsory Certification (CCC) to prevent equipment damage and safety hazards.
  6. Maintain face-to-face alignment between transmitter (TX) and receiver (RX) during operation to ensure stable signal transmission. VIMAI-V39-Wireless-Microphone  (8)

As shown in the picture below: VIMAI-V39-Wireless-Microphone  (9)

Name of Toxic/Hazardous Substances
Nameof the parts (PB) (HG) (Cd) (Cr6+) ( PBBs) ( PBOEs)
Internal Circuit Board X 0 0 0 0 0
Casing X 0 0 0 0 0
Accessories X 0 0 0 0 0
  • O: Indicates that the concentration of the hazardous substance in all homogeneous materials of this component is below the limit requirements specified in SJ/T 11364-2014.
  • X: Indicates that the concentration of the hazardous substance in at least one homogeneous material of this component exceeds the limit requirements specified in SJ/T 11364-2014.

Notes:

  1. Most components of this product are manufactured using non-toxic and environmentally friendly materials .Components containing hazardous substances are unavoidable due to global technological limitations in substituting these substances.
  2. The reference standard for environmental usage duration depends on operating temperature, humidity, and other conditions during normal product operation

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement

The device has been evaluatec to meel general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Frequently Asked Questions

  • What does “This device complies with part 15 of the FCC Rules” mean?
    This means the device has been tested and found to meet the requirements for electronic devices that emit radio frequency energy. It’s designed to operate without causing harmful interference and to accept any interference it receives.
  • Can I modify the V39 device?
  • No. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. It is strongly advised not to make any unauthorized modifications.

Documents / Resources

PDF thumbnailV39 Wireless Microphone
User Manual · 2A88Y-V39, 2A88YV39, V39, V39 Wireless Microphone, V39, Wireless Microphone, Microphone

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.