LD216-251
All-in-one Direct View LED Display
Quick Start GuideViewSonic LD216 251 All In One Direct View LED DisplayViewSonic LD216 251 All In One Direct View LED Display - fig

Package ContentsViewSonic LD216 251 All In One Direct View LED Display - fig 1ViewSonic LD216 251 All In One Direct View LED Display - fig 2

NOTE:

  • This product is packed in an air transport box.
  • Due to the size and weight, it is recommended that two or more people handle it.

Product Overview

Front PanelViewSonic LD216 251 All In One Direct View LED Display - Front PanelRear PanelViewSonic LD216 251 All In One Direct View LED Display - Rear Panel

Introduction

Before Installing

  • Maintain an adequate air gap between the back of the display and any wall for proper ventilation.
  • Ensure there is no direct airflow from air conditioning or heating vents blowing on the display.
  • Avoid installing the display in places with high humidity.
  • Due to high power usage, always use power cords specifically designed for this product.

Wall Mounting
Installing the Upper and Lower Wall Mount BracketsViewSonic LD216 251 All In One Direct View LED Display - Wall Mounting

  1. Ensure the wall area and size is an appropriate installation site.
    NOTE: The height of the Upper Wall Mount Brackets must not be less than 129.92″ (3.3 meters) from the ground.
  2. Using the Wall Mount Bracket (pictured above) as a guide, mark at least twelve (12) holes and pre-drill them.
  3. Install the first Upper Wall Mount Bracket with the provided screws (M6x50mm Expansion for masonry; TA6x30mm for load-bearing wood).
  4. Repeat step 2, ensuring the second Upper Wall Mount Bracket is level with the first upper bracket.
    ViewSonic LD216 251 All In One Direct View LED Display - Wall Mounting 1
  5. Install the Lower Wall Mount Brackets in the same manner as the Upper Wall Mount Brackets. The distance between the Upper and Lower Wall Mount Brackets is 103.94″ (2640 mm).ViewSonic LD216 251 All In One Direct View LED Display - BracketsNOTE: You can also install the Upper Wall Mount Brackets, hang the screen, and then install the Lower Wall Mount Brackets for a more precise fit.
    Ensure the wall can safely support 749.57 lbs. (340 kg).
  6. After installing both Upper and Lower Wall Mount Brackets, the installation wall should look like:

ViewSonic LD216 251 All In One Direct View LED Display - Wall Mounting 2

Installing the Middle Cabinets

  1. Ensure the Mounting Brackets on the rear of the six (6) Middle Cabinets are positioned at the top and bottom mounting positions as shown below:
    ViewSonic LD216 251 All In One Direct View LED Display - Rear Panel 2
  2. Carefully lift each Middle Cabinet up onto the Upper Wall Mount Brackets.
    ViewSonic LD216 251 All In One Direct View LED Display - Rear Panel 1
  3.  Ensure the Mounting Brackets sit securely on the Wall Mount Brackets as shown below
    ViewSonic LD216 251 All In One Direct View LED Display - Wall Mounting 3
  4. Push each Locking Bolt and lock each Hook with the hex tool to securely connect each cabinet together. It may be necessary to align the hole with an Allen wrench in order to engage the Locking Bolt.
    ViewSonic LD216 251 All In One Direct View LED Display - Rear Panel 3NOTE: There are eight (8) Locking Bolts and 16 Hooks between each cabinet.
  5. Lift the remaining Middle Cabinet up onto the Upper Wall Mount Brackets, ensuring the Mounting Brackets sit securely on the Wall Mount Brackets.
  6. Repeat step 4, securing the cabinets together with each Locking Bolt and Hook.

ViewSonic LD216 251 All In One Direct View LED Display - Rear Panel 4

Installing the Left and Right Cabinet

  1. Ensure the Mounting Brackets on the rear of the Left and Right Cabinet are positioned at the top and bottom mounting positions as shown below:ViewSonic LD216 251 All In One Direct View LED Display - Right Cabinet
  2. Carefully lift the Left and Right cabinets up onto the Upper Wall Mount Brackets, ensuring the Mounting Brackets sit securely on the Wall Mount Brackets.
    ViewSonic LD216 251 All In One Direct View LED Display - Rear Panel 5
  3. Adjust the Left or Right Cabinet so that they fit seamlessly with the Middle Cabinets. 11
  4. Push each Locking Bolt and lock each Hook with the hex tool to securely connect the Left and Right Cabinets. It may be necessary to align the hole with an Allen wrench in order to engage the Locking Bolt.ViewSonic LD216 251 All In One Direct View LED Display - Locking BoltNOTE: There are eight (8) Locking Bolts and 16 Hooks between each cabinet.

Connecting the System Control Box

  1. Carefully unfold the System Control Box panel. Ensure the main system control board is on the left.
    NOTE: Use caution as the System Control Box panel is separated into two pieces with wires attached.
  2. Align the holes of the Cabinet with the System Control Box to attach.ViewSonic LD216 251 All In One Direct View LED Display - Locking Bolt 1
  3. You can also reinstall the power cable for an attractive appearance, Loosen the three(3) PWM 4x6mm screws, pull the power cable out, thread the power cable throught the back hole, and then fasten the screws tightly.
    ViewSonic LD216 251 All In One Direct View LED Display - screws tightlyOperating by professional only.
  4. Further, secure the System Control Box to the Cabinets with the 32 provided M6x16mm screws.ViewSonic LD216 251 All In One Direct View LED Display - Front Panel 4
  5. Connect the Network and Power cables of the Cabinets to the System Control Box.
    NOTE: There are four (4) Networks and eight (8) Power cables to connect.

ViewSonic LD216 251 All In One Direct View LED Display - Rear Panel 6

Installing the LED Modules
Install each LED Module onto the Cabinets, being sure to match the corresponding numbers on the Module to the Cabinet.
Important information Please wear Anti-Static Gloves before handling the LED modules.ViewSonic LD216 251 All In One Direct View LED Display - LED modulesEnsure each Module is flush and that there is little to no gap between each. It may be necessary to gently tap the module to make it flush.
ViewSonic LD216 251 All In One Direct View LED Display - LED modules 3

Installing System Control Box Covers
There are three (3) System Control Box Covers: Left, Middle, and Right.ViewSonic LD216 251 All In One Direct View LED Display - Front Panel 2

  1. Begin by installing the Right Cover onto the System Control Box.
    NOTE: Ensure the Power Button cable is connected to the System Control Box Power cable before securing the Cover.
  2. After connecting the Power Button cable, ensure the Right Cover is properly aligned with the System Control Box; then secure it with the 18 provided KM3x6mm screws.
    ViewSonic LD216 251 All In One Direct View LED Display - LED modules 2
  3. Repeat the above steps for the Middle and Left Cover.
    ViewSonic LD216 251 All In One Direct View LED Display - LED modules 3
  4. Your display is now ready to power on.

ViewSonic LD216 251 All In One Direct View LED Display - Front Panel 3

Documents / Resources

ViewSonic LD216-251 All-In-One Direct View LED Display [pdf] User Guide
LD216-251, All-In-One Direct View LED Display, LD216-251 All-In-One Direct View LED Display
ViewSonic LD216-251 All-in-One Direct View LED Display [pdf] User Guide
LD216-251 All-in-One Direct View LED Display, LD216-251, All-in-One Direct View LED Display, LED Display, Display

Leave a comment

Your email address will not be published. Required fields are marked *