UTVS-XPD-ENC-KIT Polaris RZR Ride Command Stage 8 Stereo Kit
“
Product Specifications
- Product Name: POLARIS XPEDITION SUB ENCLOSURE KIT
- Part Number: UTVS-XPD-ENC-KIT
- Includes:
- UTVS Subwoofer Enclosure x1
- 2 Seat Lift Bar x1
- Signature Series 10 Subwoofers x2
- Gas Struts x2
- Mounting Hardware:
- L-Bracket x1
- Buttonhead Bolt x1
- Large Hex Bolts x4
- Cap Head Bolt x4
- Large Nuts x4
- Small Lock Nut x1
- Flat Washers x4
- Large Rubber Seal Washers x4
- Small Rubber Seal Washer x1
- Recommended Product: ELITE SERIES 1200.1D AMPLIFIER (PART #:
UTVS-E1200.1D) – SOLD SEPARATELY
Product Usage Instructions
Installation Steps:
- Lift the rear seat and remove the OEM gas strut on each
side. - Remove the 2 OEM bolts on each side.
- Place the 2 seat lift bar under the seat with the notch facing
the back of the vehicle on each side. - Add the UTV Stereo gas strut to the seat on each side.
- Place the supplied bolts with a washer into the lower part of
the seat lift bar on each side. - Place the OEM bolts through the top of the seat mount and into
the top of the seat lift bar, adding a nut to each. Tighten all
bolts securely on each side. - Place the subwoofer into the enclosure and pre-drill the holes
as shown on each side. - Run your subwoofer wire through the rubber grommet on each
side. - Remove the 5 OEM screws in the floor and save the long screw
for the next step. - Place the OEM bolt through the bracket and secure it to the
floor, leaving it loose until the enclosure is in the vehicle. - Place the enclosure into the vehicle and align the hole in the
enclosure with the bracket. - Use the included buttonhead bolt with a rubber seal washer and
nut to secure the bracket to the enclosure. - Use the included hardware to secure the enclosure to the floor
(2 on each side). - Wire your subwoofer for your specific impedance on each
side. - Place the subwoofer into the vehicle and secure using the
hardware included with the subwoofer on each side.
Contact Information:
We are here to help! Reach out to us at info@utvstereo.com or call us at
480.616.2299
Frequently Asked Questions (FAQ)
Q: Can I use a different amplifier with this subwoofer
enclosure kit?
A: Yes, you can use a different amplifier with this kit, but we
recommend using the ELITE SERIES 1200.1D AMPLIFIER for optimal
performance.
Q: Do I need to purchase the SUBWOOFER OUTPUT HARNESS
separately?
A: Yes, the SUBWOOFER OUTPUT HARNESS (PART #:
UTVS-JBL-RC-SUB-OUT) is sold separately and is recommended for
connecting your subwoofer to your audio system.
Q: How do I adjust the impedance of the subwoofer?
A: To adjust the impedance of the subwoofer, refer to the wiring
instructions provided with your specific subwoofer model or consult
with a professional audio installer for assistance.
“`
POLARIS XPEDITION SUB ENCLOSURE KIT
PART #: UTVS-XPD-ENC-KIT
PARTS LIST:
UTVS Subwoofer Enclosure
x1
2″ Seat Lift Bar
x1
Signature Series 10″ Subwoofers
x2
Gas Struts
x2
Mounting Hardware:
L-Bracket
x1
Buttonhead Bolt
x1
Large Hex Bolts
x4
Cap Head Bolt
x4
Large Nuts
x4
Small Lock Nut
x1
Flat Washers
x4
Large Rubber Seal Washers
x4
Small Rubber Seal Washer
x1
RECOMMENDED PRODUCTS:
ELITE SERIES 1200.1D AMPLIFIER
PART #: UTVS-E1200.1D *SOLD SEPARATELY
1.
Lift the rear seat and remove the OEM gas strut
*Repeat for other side
2.
Remove the 2 OEM bolts shown here
*Repeat for other side
5.
Place the supplied bolts with a washer into the lower part of the seat
lift bar as shown
*Repeat for other side
6.
Place the OEM bolts through the top of the seat mount and into the top of the seat lift bar and add a nut to each. Tighten all
bolts securely *Repeat for other side
3.
Place the 2″ seat lift bar under the seat with the notch facing the back
of the vehicle
7.
Place the subwoofer into the enclosure and pre-drill the holes as
shown
*Repeat for other side
4.
Add the UTV Stereo gas strut to the seat as shown
*Repeat for other side
8.
Run your subwoofer wire through the rubber grommet
*Repeat for other side
SUBWOOFER OUTPUT HARNESS
PART #: UTVS-JBL-RC-SUB-OUT
*SOLD SEPARATELY
9.
Remove the 5 OEM screws in the floor shown here. Save the long
screw for next step
10.
Place the OEM bolt through the bracket as shown and secure it to the floor
*Leave loose until the enclosure is in vehicle
11.
Place the enclosure into the vehicle and align the hole in the enclosure
with the bracket
12.
Use the included buttonhead bolt with a rubber seal washer and nut to secure the bracket to the enclosure
Scan to watch the Installation
Video!
13.
Use the included hardware to secure the enclosure to the floor (2 on each side)
*Repeat for other side
14.
You can now tighten all hardware
15.
Wire your subwoofer for your specific impedance
*Repeat for other side
16.
Place the subwoofer into the vehicle and secure using the hardware included with the subwoofer
*Repeat for other side
We are here to help! Reach out to us at info@utvstereo.com or call us at 480.616.2299
Documents / Resources
 |
UTV Stereo UTVS-XPD-ENC-KIT Polaris RZR Ride Command Stage 8 Stereo Kit [pdf] Installation Guide UTVS-XPD-ENC-KIT Polaris RZR Ride Command Stage 8 Stereo Kit, UTVS-XPD-ENC-KIT, Polaris RZR Ride Command Stage 8 Stereo Kit, RZR Ride Command Stage 8 Stereo Kit, Ride Command Stage 8 Stereo Kit, Command Stage 8 Stereo Kit, Stage 8 Stereo Kit, 8 Stereo Kit |