UNICOL-LOGO

UNICOL PSU Direct Fixing Projector Suspension

UNICOL-PSU-Direct-Fixing-Projector-Suspension-PRODUCT

Product Information

Specifications

  • Max. Projector Weight: 60kg

Product Usage Instructions

  • Loosen the Hex screws and disconnect the upper and lower parts of the PSU.
  • The upper part (T-Bar) fits to a column or peg connected to a ceiling plate or wall arm.
  • The lower part fixes to an inverted projector.
  • Cables run through the column or peg and sockets to the projector.
  • Fit the lower part of the PSU to the fixing holes of the inverted projector using the provided fixing screws.
  • Loosen the Hex screws and disconnect the upper and lower parts of the PSC.
  • The upper part (T-Bar) fits to a column or peg connected to a ceiling plate or wall arm.
  • The lower part acts as a cradle to house the projector.
  • Cables run through the column or peg and sockets to the projector.
  • Rest the projector on its feet in the base of the cradle.
  • Loosen the Hex screws and disconnect the upper and lower parts of the PPSU.
  • The upper part fits to a column or peg connected to a ceiling plate or wall arm.
  • The lower part fixes to a projector on its side. Cables run through the column or peg and sockets to the projector.
  • Fit the lower part of the PPSU to the fixing holes of the projector, on its side, with the lens pointing horizontally.
  • Loosen the Hex screws and disconnect the upper and lower parts of the VSU.
  • The upper part fits to a column or peg connected to a ceiling plate or wall arm.
  • The lower part fixes to a projector on its side. Cables run through the column or peg and sockets to the projector.
  • Fit the lower part of the VSU to the fixing holes of the projector, on its side, with the lens pointing downward.

FAQ

  • Q: Can I use this mount for projectors heavier than 60kg?
  • A: It is not recommended to exceed the specified maximum weight limit of 60kg for this mount. Please check model-specific details before installing.

PSU / PSC / PPSU / VSU

UNICOL-PSU-Direct-Fixing-Projector-Suspension-FIG-1

  • Guide Max. Projector Weight: 60kg

Please check model-specific details before installing

WARNING

  • Please carefully inspect the product before assembling it.
  • If you notice any apparent damage, call your carrier claims agent and do not continue the installation until it has been reviewed.
  • Please watch for pinch points. Do not put your fingers between moveable parts.
  • Do not tamper with or disassemble any spring-loaded parts.
  • Before installing, make sure that the supporting surface will support five times the combined load of the solution and the hardware.
  • Never exceed the maximum load capacity.
  • Please also lay out all components to ensure that you have all of the required parts before proceeding (see the BOM list on the following page).
  • Use of this product for anything other than its specified use may result in failure or personal injury.
  • This product is intended for indoor use only. We recommend using a qualified tradesperson for installation.
  • Use an assistant or lifting equipment to lift and position products.
  • For support, please call: +44 (0)1865 767676 or email: sales@unicol.com

TOOLS REQUIRED

  1. 3/16th Allen Key
  2. 13mm Spanner (for M8)
  3. 17mm Spanner (for M10)
  4. Pozidrive Screwdriver

INSTALLERS REQUIRED

  • 1-2

COMPONENTS

UNICOL-PSU-Direct-Fixing-Projector-Suspension-FIG-2

Installation Instructions

STEP 1 (inverted installation)

  • Loosen the 2 x Hex M8 or M10 hex screws and disconnect the upper and lower parts of the PSU.
  • The upper part of a PSU (T-Bar) generally fits to a column or peg connected to a ceiling plate or wall arm.
  • The lower part fixes to an inverted projector. Cables run through columns or pegs and sockets to a projector. (Alternative T-Bar shown for heavier projectors)

UNICOL-PSU-Direct-Fixing-Projector-Suspension-FIG-3

STEP 2

  • Using the fixing screws provided fit the lower part of the PSU to the fixing holes of the inverted projector.
  • The plate fixing to the projector is designed specifically for the projector ordered so may look different to the one shown.

UNICOL-PSU-Direct-Fixing-Projector-Suspension-FIG-4

PSC

STEP 1 (cradle installation)

  • Loosen the 2 x Hex M8 or M10 hex screws and disconnect the upper and lower parts of the PSC.
  • The upper part of a PSC (T-Bar) generally fits to a column or peg connected to a ceiling plate or wall arm. The lower part acts as a cradle to house the projector. Cables run through columns or pegs and sockets to a projector.

UNICOL-PSU-Direct-Fixing-Projector-Suspension-FIG-5

STEP 2

  • Rest the projector on its feet in the base of the cradle.
  • Each cradle is manufactured to suit the projector you have ordered the mount for. Balance and ventilation are taken into account within the design.

UNICOL-PSU-Direct-Fixing-Projector-Suspension-FIG-6

PPSU

STEP 1 (portrait installation)

  • Loosen the 2 x Hex M8 or M10 hex screws and disconnect the upper and lower parts of the PPSU.
  • The upper part of a PPSU generally fits to a column or peg connected to a ceiling plate or wall arm. The lower part fixes to a projector on its side. Cables run through columns or pegs and sockets to the projector.

UNICOL-PSU-Direct-Fixing-Projector-Suspension-FIG-7

STEP 2

  • Using the fixing screws provided fit the lower part of the PPSU to the fixing holes of the projector, on its side, lens pointing horizontally.
  • The plate fixing to the projector is designed specifically for the projector ordered so may look different to the one shown.

UNICOL-PSU-Direct-Fixing-Projector-Suspension-FIG-8

VSU

STEP 1 (vertical installation)

  • Loosen the 2 x Hex M8 or M10 hex screws and disconnect the upper and lower parts of the VSU.
  • The upper part of a VSU generally fits to a column or peg connected to a ceiling plate or wall arm. The lower part fixes to a projector on its side. Cables run through columns or pegs and sockets to projector.

UNICOL-PSU-Direct-Fixing-Projector-Suspension-FIG-9

STEP 2

  • Using the fixing screws provided fit the lower part of the VSU to the fixing holes of the projector, on its side, with the lens pointing downward.
  • The plate fixing to the projector is designed specifically for the projector ordered so may look different to the one shown.

UNICOL-PSU-Direct-Fixing-Projector-Suspension-FIG-10

CEILING SUSPENSION

STEP 1 (typical installation shown)

  • Remove the through-bolt in the upper part of the bar assembly socket and loosen the grub screws. Align socket with column or peg. Thread cables through the socket. Insert through-bolt and tighten. Tighten grub screws.
  • Safety through-bolts must be used to secure the unit.
  • Grub screws are used to remove slack in the joint.

UNICOL-PSU-Direct-Fixing-Projector-Suspension-FIG-11

STEP 2 (PSU shown)

  • Hook the lower part with the projector over the 2 x M8/M10 hex screws.
  • Cable up the projector and set tilt angles then tighten M8/M10 hex screws. Set the rotation angle by turning the projector either way to finish the installation.
  • Beware of stretching cables when adjusting angles.

UNICOL-PSU-Direct-Fixing-Projector-Suspension-FIG-12

STEP 2 (PSU shown)

  • Hook the lower part with the projector over the 2 x M8/M10 hex screws.
  • Cable up the projector and set tilt angles then tighten M8/M10 hex screws.
  • Set the rotation angle by turning the projector either way to finish the installation.
  • Beware of stretching cables when adjusting angles.

UNICOL-PSU-Direct-Fixing-Projector-Suspension-FIG-13

STEP 4 (PPSU & VSU shown)

  • Hook the lower part with the projector over the 2 x M8/M10 hex screws.
  • Cable up the projector and set tilt angles then tighten M8/M10 hex screws.
  • Set the rotation angle by turning the projector either way to finish the installation.
  • Beware of stretching cables when adjusting angles.

UNICOL-PSU-Direct-Fixing-Projector-Suspension-FIG-14UNICOL-PSU-Direct-Fixing-Projector-Suspension-FIG-15

CONTACT

Documents / Resources

UNICOL PSU Direct Fixing Projector Suspension Unit [pdf] Instructions
PSU, PSC, PPSU, VSU, PSU Direct Fixing Projector Suspension Unit, PSU, Direct Fixing Projector Suspension Unit, Fixing Projector Suspension Unit, Projector Suspension Unit, Suspension Unit, Unit

References

Leave a comment

Your email address will not be published. Required fields are marked *