U-PROX SE Maxi Versatile Reader Instructions

The adjustable versatile SmartLine second edition (SE) reader for mobile credentials and proximity identifiers in conjunction with the U-Prox Mobile ID application and U-Prox IDs will allow any access control system to use smartphones as access system credentials.

U-Prox ID

Digital personal mobile credential. It is processed and stored in the user’s smartphone using the U-Prox Mobile ID application. It can be transferred over NFC and/or 2.4 GHz radio between the reader and the smartphone.

via NFC for Android only
Read range 2-5 cm. Recommended for double-sided doors and turnstiles.

via 2.4 GHz radio for Apple and Android

Reader supports 3 operation modes for smartphones with U-Prox ID:

“Door-Proximity” – 10-20 cm, reader activates by built-in IR sensor.
Recommended for double-sided doors and turnstiles

“Door” – up to 60-70 cm
“Barrier/Gate” – adjustable range of interaction from 1 to 15 m

Mifare® и Mifare®Plus

Operates with ISO14443A identifiers, supports SL1 and SL3 modes for Mifare®Plus. Read range — up to 5 cm.
Reads encrypted identifiers with static or diversified key and with an arbitrary card number.
Simultaneous use of five encryption profiles.

RFID, 125 kHz
Supports RFID 125 kHz – EmMarine and other formats.

Easy connection

Seamless and easy connection to existing and new access systems, due to the OSDP, Wiegand 26, 32, 34, 37, 40, 42, 56, 58, 64, 80 bit interfaces, Wiegand with automatic selection, RS232 and TouchMemory supports.

Integration

OSDP or RS-232 protocols for integration into arbitrary systems.
The encrypted OSDP protocol provides safe management of all parameters of the reader including credential encryption keys from the panel.

Mobile Apps

Free mobile application U-Prox Mobile ID receives, stores and transmits mobile credentials U-Prox ID between the reader and the smartphone.

With the free mobile application U-Prox Config, the reader can be completely adjusted — from the indication to the encryption modes.

The reader is supplied without the engineering password for programming specified. To connect and (re) set the password — connect inputs D0 (green) and D1 (white) with each other and apply power to the reader.

Warning!!! The reader firmware can be updated with an NFC-enabled Android smartphone only.

Benefits

Read range	NFC, Mifare and RFID 125 kHz – up to 5 cm, 2.4 GHz radio – adjustable 10 cm – 15 m
Mifare®, 13.56 MHz	IS014443A: Mifare®Standard, Mifare0Hi-Memory, Mifare0Ultralight, Mifare®Classic 1K/4K, Mifare®Classic 7UID, Mifare® Plus S 2K, Mifare® Plus S 4K, Mifare® Plus SE 1K, Mifare® Plus X 2K, Mifare® Plus X 4K, Mifare® Plus EV1 2K, Mifare® Plus EV1 4K, Mifare® DESfire, Mifare® DESfire EV1, Mifare® DESfire EV2
NFC, 13.56 MHz	ISO 14443/15693
RFID, 125 kHz	ASK and FSK
Case material & Color	ABS+PC plastic, black
Dimensions	42.8 x 157.8 x 16 mm
Weight	120 g
Ambient	IP65, -40°C … +60°C
Power supply	+9… +15 VDC, max current- up to 90 mAVoltage ripple – up to 500 mVp-p
Interfaces	OSDP, Wiegand Auto, 26, 32, 34, 37, 40, 42, 56, 58, 64, 80 bits, RS232 and TouchMemory
Wiring	8 wire cable, maximum distance to panel – up to 150 m for Wiegand interface, up to 30 M m for TouchMemory interface, up to 1000 m for OSDP interface

Wiring

The reader connection wires functions are listed in the table. We recommend to use multi-core signal cable with 0.22 mm² cross-section of each wire between reader and panel.

Color	Wiegand	RS232	TouchMemory	OSDP
Green	Data0 (WD0)	Rx iButton		A+
White	Data1 (WD1)	Tx		B-
Red		+V, 12 VDC
Black		GND
Brown	Red Led		Red Led
Orange	Green Led		Green Led
Blue	Beep		Beep
Yellow	Hold/Sync	Hold/Sync Hold/Sync

Reader turns to the hold mode while yellow wire is shorted to ground and does not read any identifiers.
It is prohibited to supply the external voltage to the yellow wire!
Reader connection to the panel with twisted pair.

Reader Installation

Installation on the metal surfaces without the supplied plastic wafer may cause decrease of reading range. Do not place readers closer than 20 cm one from another. It is possible to install two readers at a distance 10-15 cm of each other when their yellow wires (Hold/Sync) interconnected. This synchronizes the work of the readers, they will work alternately.

Make small recess or hole (diameter is 14 mm) to connect cable under the reader’s case
Loosen the screw at the bottom of the reader
Remove the top cover
When mounting on a metal surface, use the plastic wafer
Carry out wiring to the control panel
Fasten the reader to the wall, using supplied plastic dowels and screws
Place the top cover and tighten it with a screw

Limited Warranty

The reader connection wires functions are listed in the table. We recommend to use multi-core signal cable with 0.22 mm² cross-section of each wire between reader and panel.
Manufacturer warrants that for a period of thirty six months from the date of purchase, the product shall be free of defect in materials and workmanship under normal use and that in fulfillment of any breach of such warranty, Integrated Technical Vision ltd. shall, at its option, repair or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies only to defects in parts and workmanship and not damages incurred in shipping or handing, or damages due to causes beyond the control of Manufacturer such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper application of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of Manufacturer This warranty contains the entire warranty. Manufacturer neither assumes, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any warranty or liability concerning this product.
In no event shall Manufacturer be liable for any direct, indirect or consequential damages. Loss of anticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installation or operation or failure of this product.

Documents / Resources

U-PROX SE Maxi Versatile Reader [pdf] Instructions
SE Maxi, Versatile Reader, Reader, SE Maxi

References

User Manual

Instructions