Trimble R980 GNSS System

PRODUCT Overview

CAUTION – Before operating this product, read the safety warnings and information. Go to receiverhelp.trimble.com/r980-gnss
Charge the Lithium-Ion battery
The rechargeable Lithium-ion battery is supplied partially charged. Before using the battery for the first time, charge it completely using the dual slot battery charger and country-specific power supply and power cord. The battery has built-in charge indicator LEDs. Push the button on the battery to check the battery charge status. Charging takes approximately 3 hours at room temperature. If two batteries are charging in the dual battery charger, the batteries will be charged simultaneously.
CAUTION – Before operating the dual slot battery charger, review the safety notes and operating instructions in the Trimble Dual Slot Battery Charger (P/N 109000) User Guide.
Insert the battery
Open the battery door by pushing down on the battery door latch and allowing the door to spring open. Insert the battery with the metal contacts facing up and to the rear of the battery bay. Push the battery until the battery bail engages. To remove the battery, slide the battery bail to the left until the battery is released.
Power on the receiver
Power on the receiver by pressing and releasing the power button on the front panel. All four LEDs light up, remain lit for 3 seconds and then turn off. The power LED then immediately lights up again.
To turn off the receiver, hold the power button for 2 seconds and then release it. When holding down the power button, the battery LED remains lit, the satellite LED lights up constantly and then turns off after 2 seconds. After releasing the power button, the battery LED stays lit for about 5 seconds and then all LEDs turn off.
NOTE — See the online receiver help guide for full LED blink pattern definitions. Go to receiverhelp.trimble.com/r980-gnss.
Activate warranties, install options, install radio frequencies, and update firmware
- Install Trimble® Installation Manager on your PC or Trimble data collector. Go to install.trimble.com
- Connect the receiver to your computer using a USB (e.g. P/N 80751) or serial cable (e.g. P/N 59044, 59046).
- Start Trimble Installation Manager.
- Select the Receiver tab and click Connect.
- Select COMx Trimble USB from the list of available ports and click OK.
Connect the UHF radio antenna
Connect the UHF antenna (P/N 129988) or external UHF antenna cable (P/N 130626-05) to the RP-SMA connector on the receiver. Do not overtighten.
Install the SIM card (optional)
Insert the SIM card with the contacts facing upward, as indicated by the SIM card icon next to the SIM card slot. To eject the SIM card, slightly push it in to trigger the spring-loaded release mechanism.

Attach the Quick Release adapter
- Push down the spring-loaded button of the quick release adapter.
- Align the white dots on the bottom of the receiver and the quick release adapter.
- Slide in the quick release adapter and then release the button.
Antenna measurement methods
Connect to the receiver Web Interface
- Power on the receiver.
- Find the receiver SSID under the available Wi-Fi networks on your computer or smart device. The default SSID is Trimble GNSS xxxx, where xxxx represents the last four digits of the receiver serial number.
- Select the receiver SSID and connect to the Wi-Fi access point.
The default network password is abcdeabcde. - On your computer or smart device:
a. Open a web browser and enter the IP address: http://192.168.142.1
b. Log into the web interface. The default login credentials are:- User name: admin
- Password: password
- The first time you connect to the web interface, you are prompted to change the default login credentials
Regulatory information
For full legal and regulatory information, go to https://receiverhelp.trimble.com/r980-gnss.
USA
FCC Compliance Statement
Model Numbers: R980
FCC Class B – Notice to Users. This device complies with part 15 of the FCC rules.
RESPONSIBLE PARTY:
Trimble Inc.
10368 Westmoor Drive, Westminster CO 80021 USA.
trimble.com/Corporate/Contacts.aspx
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by Trimble Inc may void the FCC authorization to operate this equipment.
FCC Certified Modular Transceiver
The Thales PLS63-W (P/N 124213), Singular-Modular Transceiver (LTE) was tested and certified per FCC Part 22, 24, 27, (FCC ID: QIPPLS63-W) with an internal antenna not accessible by the user. The Texas Instruments WL1837MODGIMOC (P/N 103488), Singular-Modular Transceiver (Wi-Fi/BT) was tested and certified per FCC Part 15C (FCC ID: Z64-WL18DBMOD) with an internal antenna not accessible by the user. The TR400900 (P/N 123130), Singular-Modular Transceiver (410 MHz to 470 MHz / 902 MHz – 928 MHz) was tested and certified per FCC Part 15.247 and Part 90 (FCC ID: S9E123130) for use with the antenna listed below:
- A monopole antenna with peak gain of 1.85 dBi (410 MHz to 470 MHz) and 3.28 dBi (902 MHz to 928 MHz) and RP-SMA connector (P/N 129988).
- A monopole antenna (P/N 24253-xx) with peak gain of 5.0 dBi (410 MHz to 470 MHz / 902 MHz to 928 MHz) and 5 m RG58 cable with RP-SMA connector (P/N 130626-05)
Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
United Kingdom
Hereby, Trimble Inc., declares that the R980 GNSS receiver complies with the following UK legislations:
- S.I. 2016 No. 1101, Low Voltage, RF Exposure
- S.I. 2016 No. 1091, EMI/EMC
- S.I. 2017 No. 1206, Radio Equipment
Australia and New Zealand
This product conforms with the regulatory requirements of the Australian Communications and Media Authority (ACMA) Radiocommunications Act.
Europe
Hereby, Trimble Inc., declares that the R980 GNSS receiver complies with the following directives:
- RED 2014/53/EU
- RoHS Directive 2011/65/EU
- WEEE Directive 2012/19/EU
CE marking
The products covered by this guide may be operated in all EU member countries (BE, BG, CZ, DK, DE, EE, IE, EL, ES, FR, HR, IT, CY, LV, LT, LU, HU, MT, NL, AT, PL, PT, RO, SI, SK, FI, SE), Norway and Switzerland. Product has been tested and found to comply with the requirements for a Radio Equipment device pursuant to European Council Directive 2014/53/EU on Radio Equipment, thereby satisfying the requirements for CE Marking and sale within the European Economic Area EEA). Contains a Bluetooth radio module. These requirements are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential or commercial environmen.
Recycling
For product recycling instructions and more information, go to www.trimble.com/en/our-commitment/responsible-business/product-compliance/environmental-compliance
Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Apple, iPad, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries and regions Google Play and the Google Play logo are trademarks of Google LLC.

© 2024, Trimble Inc. All rights reserved. Trimble and the Globe & Triangle logo are trademarks of Trimble, registered in the United States and in other countries. All other trademarks are the property of their respective owners. P/N 89908-00-ENG, Rev C (03/2024).
Trimble Inc. 10368 Westmoor Drive Westminster CO 80021 USA
FAQ
- Q: How do I connect the UHF radio antenna?
- A: Connect the UHF antenna (P/N 129988) or external UHF antenna cable (P/N 130626-05) to the RP-SMA connector on the receiver. Do not overtighten.
- Q: How do I access the receiver Web Interface?
- A: Power on the receiver and find the receiver’s SSID under available Wi-Fi networks on your computer or smart device. Connect to the SSID with the default password ‘abcdeabcde’. Open a web browser and enter the IP address to access the interface.
Documents / Resources
![]() | R980 GNSS System |
References
- User Manualmanual.tools

