Trimble R980 GNSS System

System Overview

The Trimble R980 GNSS receiver is a sophisticated device for precise positioning. Key components and connections are labeled:

• ? Radio
• ⬇️ Data logging / download
• ?️ Satellite
• ? Wi-Fi
• ? Power button with battery LED
• ? SIM card slot
• ? Battery compartment with removable battery
• Port 1 (black): serial / power in ?
• Port 2 (yellow): USB / power in ?
• RP-SMA UHF radio antenna connector (for receiver models with internal radio only)
• Quick release adapter with 5/8-11 threaded insert

⚠️ CAUTION - Before operating this product, read the safety warnings and information. Go to receiverhelp.trimble.com/r980-gnss.

Charge the Lithium-Ion battery

The rechargeable Lithium-ion battery is supplied partially charged. For first-time use, charge it completely using the dual slot battery charger and country-specific power supply and cord. The battery has built-in charge indicator LEDs; push the button on the battery to check its status. Charging takes approximately 3 hours at room temperature. Two batteries can charge simultaneously in the dual battery charger.

Diagram Description: The document shows a dual slot battery charger with two batteries being charged, and an image of the Trimble R980 receiver with its battery compartment open, illustrating battery insertion.

⚠️ CAUTION - Before operating the dual slot battery charger, review the safety notes and operating instructions in the Trimble Dual Slot Battery Charger (P/N 109000) User Guide.

Insert the battery

To insert the battery, open the battery door by pushing down on the latch. Insert the battery with the metal contacts facing up and towards the rear of the bay. Push until the battery bail engages. To remove the battery, slide the bail to the left until it releases.

Power on the receiver

Press and release the power button on the front panel to power on the receiver. Initially, all four LEDs will light up for 3 seconds, then turn off, followed by the power LED lighting up again. To power off, hold the power button for 2 seconds. During power off, the battery LED stays lit, the satellite LED lights up and turns off after 2 seconds, and the battery LED remains lit for about 5 seconds before all LEDs turn off.

ℹ️ NOTE – For full LED blink pattern definitions, consult the online receiver help guide at receiverhelp.trimble.com/r980-gnss.

Activate Warranties, Install Options, Radio Frequencies, and Update Firmware

1. Install Trimble® Installation Manager on your PC or Trimble data collector. Access it at install.trimble.com.
2. Connect the receiver to your computer using a USB cable (e.g., P/N 80751) or a serial cable (e.g., P/N 59044, 59046).
3. Start Trimble Installation Manager.
4. Select the 'Receiver' tab and click 'Connect'.
5. Choose 'COMx Trimble USB' from the list of available ports and click 'OK'.

Connect the UHF radio antenna

Connect the UHF antenna (P/N 129988) or external UHF antenna cable (P/N 130626-05) to the RP-SMA connector on the receiver. Do not overtighten.

Install the SIM card (optional)

Insert the SIM card with the contacts facing upward, as indicated by the SIM card icon next to the slot. To eject the SIM card, push it slightly to trigger the spring-loaded release mechanism.

Attach the Quick Release adapter

1. Push down the spring-loaded button of the quick release adapter.
2. Align the white dots on the bottom of the receiver and the quick release adapter.
3. Slide the quick release adapter into place and release the button.

Antenna measurement methods

Measurement points for antenna setup are identified as:

• Bottom of antenna mount
• Bottom of quick release
• Lever of R980 extension

Connect to the receiver Web Interface

1. Power on the receiver.
2. On your computer or smart device, find the receiver's SSID in available Wi-Fi networks. The default SSID is 'Trimble GNSS xxxx', where 'xxxx' represents the last four digits of the receiver's serial number.
3. Select the receiver SSID and connect to the Wi-Fi access point. The default network password is 'abcdeabcde'.
4. Open a web browser and enter the IP address: http://192.168.142.1
5. Log in using the default credentials: User name: 'admin', Password: 'password'.
6. You will be prompted to change the default login credentials upon your first connection.

Regulatory Information

For comprehensive legal and regulatory details, visit receiverhelp.trimble.com/r980-gnss.

USA

FCC Compliance Statement: Model Numbers: R980. This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: it must not cause harmful interference, and it must accept any interference received. Changes not expressly approved by Trimble Inc. may void FCC authorization.

Responsible Party: Trimble Inc., 10368 Westmoor Drive, Westminster CO 80021 USA. (trimble.com/Corporate/Contacts.aspx)

FCC Certified Modular Transceiver: Details provided for Thales PLS63-W (LTE), Texas Instruments WL1837MODGIMOC (Wi-Fi/BT), and TR400900 (410-470 MHz / 902-928 MHz) with FCC IDs and antenna specifications.

Canada

This device complies with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the conditions of not causing interference and accepting any interference. Industry Canada regulations require antenna type and gain selection for optimal EIRP. The device also complies with Canadian ICES-003, NMB-003, and various RSS standards (RSS-GEN, RSS-102, RSS-247, RSS-119, RSS-130/132/133/139/199).

United Kingdom

Trimble Inc. declares that the R980 GNSS receiver complies with UK legislations: S.I. 2016 No. 1101 (Low Voltage, RF Exposure), S.I. 2016 No. 1091 (EMI/EMC), and S.I. 2017 No. 1206 (Radio Equipment).

Australia and New Zealand

This product conforms to the regulatory requirements of the Australian Communications and Media Authority (ACMA) Radiocommunications Act.

Europe

Trimble Inc. declares that the R980 GNSS receiver complies with directives RED 2014/53/EU, RoHS Directive 2011/65/EU, and WEEE Directive 2012/19/EU. It meets CE marking requirements and is approved for operation in EU member countries, Norway, and Switzerland. The device contains a Bluetooth radio module and is designed to provide protection against harmful interference.

Recycling

For product recycling instructions and information, visit www.trimble.com/en/our-commitment/responsible-business/product-compliance/environmental-compliance.

Product Information and Trademarks

Diagram Description: The document displays badges indicating "Made for iPhone | iPad" and "Get it on Google Play".

Use of the "Made for Apple" badge signifies that the accessory is designed to connect specifically to Apple products and meets Apple performance standards. Apple is not responsible for the operation or regulatory compliance of this device.

Apple, iPad, and iPhone are trademarks of Apple Inc.

Google Play and the Google Play logo are trademarks of Google LLC.

© 2024, Trimble Inc. All rights reserved. Trimble, and the Globe & Triangle logo are trademarks of Trimble, registered in the United States and other countries. All other trademarks are the property of their respective owners.

Product Number: P/N 89908-00-ENG, Rev C (03/2024).

Trimble Inc.
10368 Westmoor Drive
Westminster CO 80021
USA