LC3040 Wireless Service Tool
“
Specifications
- Product Name: Wireless Service Tool
- Part Number: LC3040
- Created: August 7, 2024
- Power Source: Water source heat pump control or USB-C port
- Wi-Fi: 2.4Ghz antenna, up to 20 feet range
- Water Resistance: Not water resistant
Product Usage Instructions
Connecting to Water-Source Heat Pump (Wired)
- Plug the green connector into the WST.
- Plug the white connector into the port on the corner post of
the WSHP. - The TX/RX LEDs on the WST will illuminate indicating
communication with the unit control board.
Connecting to CXM2/DXM2.5 (Wired)
- Disconnect power from the WSHP, remove the front access panel,
and open the control panel. - Plug the green connector into the WST.
- Plug the white connector into the communications port on the
CXM2 or DXM2.5. - Power on the WSHP. The RX/TX LEDs on the WST will illuminate
indicating communication with the unit control board.
Linking a Wi-Fi Enabled Device
- Ensure RX/TX lights on the WST are flashing.
- Access the WST web application using either automatic or manual
method.
Automatic Method:
- Scan the QR code on the back of the WST using your device’s
camera.
Manual Method:
- Open Wi-Fi settings on your device and select WSTXXX from
available networks.
- The green status LED will illuminate indicating communication
with your device. - Open your device’s browser and enter 192.168.4.1 if the WST Web
App does not display.
FAQ
Q: Is the Wireless Service Tool water-resistant?
A: No, the Wireless Service Tool is not water-resistant. Avoid
exposure to water to prevent damage.
Q: How far can the Wireless Service Tool communicate with a
Wi-Fi enabled device?
A: The Wireless Service Tool can communicate with one Wi-Fi
enabled device up to 20 feet away.
Q: What is the Wi-Fi passcode for the Wireless Service
Tool?
A: The Wi-Fi passcode for the Wireless Service Tool is
12345678.
“`
WIRELESS SERVICE TOOL
QUICK START GUIDE
For All Tranquility Water-Source Products
Part#: LC3040 | Created: August 7, 2024
ABOUT YOUR WIRELESS SERVICE TOOL (WST)
z Power is supplied by the water source heat pump control or by a USB-C port
z 2.4Ghz Wi-Fi antenna z The WST is NOT water resistant z Can communicate with ONE Wi-Fi enabled
device that is up to 20 feet from the WST
WIRELESS SERVICE TOOL QUICK START GUIDE
LED Light Indicators
1. Power LED indicates the WST is powered.
1
2. Modbus TX/RX LEDs indicates the WST is communicating with the WSHP.
2
3. Status LED indicates the WST is communicating with a Wi-Fi enabled device.
3
4
4. Fault LED flashes every 5 seconds during normal status and fast flashes during
an OTA update.
Connect the Wireless Service Tool to a Water-Source Heat Pump (Wired)
If connecting to the port outside the unit located on the corner post (Figure 2), use harness part number 11B0100N79 (Figure 1).
1. Plug the green connector into the WST.
3. The TX/RX LEDs on the WST illuminate indicating the WST is communicating with the unit control board.
Figure 2: Service Tool Ports
2. Plug the white connector into the port on the corner post of the WSHP.
Figure 1: 11B0100N79
USB-C port
RS-485 port for connecting harness to the WSHP
Part#: LC3040 | Revised: August 7, 2024
WIRELESS SERVICE TOOL QUICK START GUIDE
CONNECT THE WIRELESS SERVICE TOOL TO A CXM2/DXM2.5 (WIRED)
If connecting to the port located on the CXM2 or DXM2.5 control, use harness part number 11B0100N80 (Figure 3). 1. Disconnect power from the WSHP, remove the unit
front access panel, and open the control panel. 2. Plug the green connector into the WST. 3. Plug the white connector into the communications
port on the CXM2 or DXM2.5 per Figure 4. 4. Power on the WSHP. 5. The RX/TX LEDs on the WST illuminate indicating the
WST is communicating with the unit control board.
Figure 3: 11B0100N80
Figure 4: Connection to WST for DXM2.5 or CXM2
11B0100N80 CXM2
DXM2.5 WST
Part#: LC3040 | Revised: August 7, 2024
WIRELESS SERVICE TOOL QUICK START GUIDE
LINK A WI-FI ENABLED DEVICE TO THE WIRELESS SERVICE TOOL
Before you begin, ensure the RX/TX lights on the WST are flashing. Choose one of the following methods to access the WST web application:
NOTE: The WST Wi-Fi passcode is 12345678.
z Automatic method: Using the camera on your Wi-Fi enabled device, scan the QR code on the back of the WST.
z Manual method:
1. Open the Wi-Fi settings on your Wi-Fi enabled device.
2. Find WSTXXX in available networks then select it.
NAVIGATE TO THE WEB APP
1. The green status LED illuminates and remains solid indicating that the WST is communicating with your Wi-Fi enabled device.
2. Open the browser on your Wi-Fi enabled device.
3. If the WST Web App does not display in the browser, enter the following address: 192.168.4.1
WIRELESS SERVICE TOOL APPLICATION, OPERATION & MAINTENANCE MANUAL
For detailed Wireless Service Tool information, see the WST Application, Operation, and Maintenance (AOM) manual (part #97B0169N01).
Part#: LC3040 | Revised: August 7, 2024
*LC3040*
We work continually to improve our products. As a result, the design and specifications of each product at the time of order may be changed without notice and may not be as described herein. Please contact our Customer Service Department at 800-299-9747 for specific information on the current design and specifications. Statements and other information contained herein are not express warranties and do not form the basis of any bargain between the parties, but are merely our opinion or commendation of its products. Engineered and assembled in the USA. © ClimateMaster’, Inc. All Rights Reserved 2024
Documents / Resources
 |
tranquility LC3040 Wireless Service Tool [pdf] User Guide LC3040, LC3040 Wireless Service Tool, Wireless Service Tool, Service Tool, Tool |