PUPP1G Power Point Switched
“
Specifications:
- Catalogue Number: PUPP1G, PUPP151G, PUPP201G, PUPPSW1G,
PUPPV1G, PUPP1GL - Description:
- Power Point Switched 1 Gang 10A 250V~ (PUPP1G)
- Power Point Switched 1 Gang 15A 250V~ (PUPP151G)
- Power Point Switched 1 Gang 20A 250V~ (PUPP201G)
- Power Point Switched 1 Gang 10A 250V~ With Extra Switch,
10AX/16A (PUPPSW1G) - Power Point Switched Vertical 1 Gang 10A 250V~ (PUPPV1G)
- Power Point Switched 1 Gang 10A 250V~ with Lighting Pin
(PUPP1GL)
- Certification Number:
- PUPP1G: GMA-509981-EA
- PUPP151G: GMA-509981-EA
- PUPPSW1G: GMA-501109-EA
- PUPPV1G: GMA-501807-EA
Product Usage Instructions:
Installation:
- Ensure power is turned off before installation.
- Mount the power point securely on the wall using appropriate
screws. - Connect the wiring following the provided instructions or seek
professional assistance. - Once wired, attach the cover plate onto the power point.
Operation:
To use the power point, simply plug in your electronic devices
into the socket and switch on the power if applicable.
Maintenance:
Regularly check for any signs of damage or wear. Clean the power
point with a dry cloth to remove dust or debris.
FAQ:
Q: Can I use these power points outdoors?
A: These power points are designed for indoor use only and
should not be exposed to outdoor elements.
Q: What should I do if the power point stops working?
A: Check the circuit breaker and ensure there is power supply to
the outlet. If issues persist, contact a qualified electrician for
further assistance.
“`
PUPP1G PUPP151G PUPP201G PUPPSW1G PUPPV1G PUPP1GL
*See current catalogue for further detail
Puma Range of Single Power Points
· Uses brass tunnel terminals that have the screws backed out for easier installation of cabling. Power point terminals have 5.7mm bore to suit 4 x 2.5mm2 cable.
· Fits standard Australian wall boxes and mounting accessories that use 84mm mounting centres.
· Covers, plates and dollies are made from UV stabilised polycarbonate to avoid discolouring to yellow.
· Standard colour is white. Black also stocked – please check availability. · Switches approved to AS/NZS3133. · Power points approved to AS/NZS3112. · Typical example of size seen below:
117
Cleaning Guide: Spraying cleaning products directly on to electrical switches or power points (sockets) is not recommended. It is important to ensure that switches are turned off before cleaning. Do not use any cleaning sprays – only wipe down with damp cloth or rub with dry cloth. Do not use an abrasive cloth as it may scratch the plastic. Do not use harsh chemical cleaners as these can break down the plastic and cause it to crack. Do not wash the cover plates in water over 60°C.
1
76
13
28
Catalogue Number PUPP1G PUPP151G PUPP201G
PUPPSW1G
PUPPV1G PUPP1GL
Description
Power Point Switched 1 Gang 10A 250V~ Power Point Switched 1 Gang 15A 250V~ Power Point Switched 1 Gang 20A 250V~ Power Point Switched 1 Gang 10A 250V~ With Extra Switch, 10AX/16A Power Point Switched Vertical 1 Gang 10A 250V~ Power Point Switched 1 Gang 10A 250V~ with Lighting Pin
When ordering BLACK product add “BK” at end of catalogue number, ie PUPP1GBK When ordering BRUSHED ALUMINIUM (cover) add “CBA” at end of catalogue number, ie PUPP1GCBA When ordering REPLACEMENT “COVERS ONLY” add “CO” at end of catalogue number, ie PUPP1GCO
Certification Number: PUPP1G: GMA-509981-EA PUPP151G: GMA-509981-EA PUPPSW1G: GMA-501109-EA PUPPV1G: GMA-501807-EA
GSM Electrical (Australia) Pty Ltd Level 2, 142-144 Fullarton Road, Rose Park SA 5067 P: 1300 301 838 F: 1300 301 778 E: service@gsme.com.au
www.gsme.com.au
Data Specification Sheet 230727
Documents / Resources
 |
Trader PUPP1G Power Point Switched [pdf] Owner's Manual PUPP1G, PUPP151G, PUPP201G, PUPPSW1G, PUPPV1G, PUPP1GL, PUPP1G Power Point Switched, PUPP1G, Power Point Switched, Point Switched, Switched |