TopVision TP-B01 Wifi Camera

Specifications

• Model: TP-B01
• Antenna Type: Supplied antenna
• Compliance: FCC’s RF Exposure guidelines

Product Usage Instructions

FCC Caution

• Connect the equipment to an outlet on a circuit that is different from the one to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• To maintain compliance with the FCC’s RF Exposure guidelines, this equipment should be installed and operated with a minimum distance between the radiator and your body.
• Use only the supplied antenna.

Installation

1. Locate a power outlet on a circuit different from the one the receiver is connected to.
2. Connect the equipment to the power outlet.
3. Ensure the supplied antenna is properly attached for optimal performance.

Operation

1. Turn on the equipment using the power button.
2. Adjust settings as needed for your desired operation.
3. Avoid placing the equipment too close to your body to comply with FCC guidelines.

Please read the Manual carefully before using the product and keep it properly.

Connection Instructions

Connect the power interface and the power socket with the power cord.

Installation guide

Choose a location
Please install the camera in a location where the field of view is not blocked, and make sure that the location of the camera has a good wifi signal.

Voice broadcast instructions

Camera reset

When the camera is powered on, press and hold the reset button for 3-5 seconds until you hear a voice prompt and a prompt sound of “reset is complete, the device will be restarted soon”; that is, the reset is successful.

Device connection

Download the APP
Scan the QR code below to download and install the APP.

Register and log in to the APP

1. Please register for an APP account and log in.
2. If you have already registered, please log in directly.

Connection method—Bluetooth

1. Find the device Bluetooth, and click iConnect.” Find the device
2. Click “+Add, i the Bluetooth page, and click jump to figure 2. Connect. “
3. Select WiFi, enter the correct password, and click “Next.”
4. Waiting for connection,

Connection method—Scan the QR code

1. Is Click “+” to add device,
2. Scan the QR code on the camera label.
3. Upon hearing a sound or seeing the indicator light flashing, check and click “Next.”
4. Select WiFi, enter the correct password, and click “Next.”
5. Align the QR code with the camera.
6. Click on the input box, customize the device name, and click “Get started.”

Device sharing

With open permission of Device sharing, the person being shared can set the function of the device. If the permission is turned off, you can only watch the video, and cannot set the function.

Rotation control

PTZ and functions

A1 function

Warranty Card

FCC Caution:
This device complies. With part 15 of the FCC Rules.

The operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. thThisevice must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the uusers’sauthority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or. More of the following measures :

• Reorient or relocate. The receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet or circuit different from the one on which. The cone is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with the FCC’s RF Exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
Use only the supplied antenna.

FAQs

Will the camera display a red light after turning on the night vision function?

The built-in IR LED lights, when the night vision is turned on, the camera only displays some faint red lights, but the picture quality is still clear in the dark environment.

How far should the camera be from the router?

After testing, the Wi-Fi connection distance can normally reach 150 meters in an open area. But the actual situation depends on the strength of the Wi-Fi and its surroundings (thick walls, electromagnetic devices, and large metal objects can all cause interference to the Wi-Fi signal). If the camera connection is weak or unstable, place the camera as close to the router as possible.

What should I do if the equipment fails?

Long press the power button to restart the camera, If there is no response, you can open the USB silicone cover at the bottom of the camera, long press the reset button to reset, and then long press the power button to restart the camera.

Documents / Resources

TopVision TP-B01 Wifi Camera [pdf] User Manual 2BK5B-TP-B01, 2BK5BTPB01, TP-B01 Wifi Camera, TP-B01, Wifi Camera, Camera

References

• User Manual