Tenda R10, T10 N300 Wi-Fi Range Extender Installation Guide

Connect your smartphone to the extender’s Wi-Fi (Tenda_EXT) and
access the web UI by tapping Start Now.
Select the Wi-Fi to be extended (router’s Wi-Fi) and follow
on-screen instructions to complete the setup.

Method 2: Via WPS Button

Press the WPS button on the router for 1-3 seconds to enable
WPS function.

Within 2 minutes, press the WPS button on the extender for 1-3
seconds until the LED indicator blinks green fast. Once solid,
setup is successful.

Extender Info:

Wi-Fi Name: Tenda_XXXXXX_EXT

Wi-Fi Password: XXXXXXXX
Management Address: re.tenda.cn

Management Password: XXXXXXXX

Frequently Asked Questions (FAQ)

Q: How can I find the Wi-Fi name and password after setup?

A: After successful setup, the Wi-Fi name is Tenda_XXXXXX_EXT
and the password is XXXXXXXX. You can also find this information in
the extender’s settings.

Q: What should I do if the WPS setup method fails?

A: If the WPS setup method fails, you can try configuring the
extender via a smartphone web browser following the alternative
method provided in the user manual.

“`

View Fullscreen

Quick Installation Guide
N300 Wi-Fi Range Extender R10/T10

Video and More Info

Scan the QR code or visit www.tendacn.com for installation videos, technical specifications, user guides, Symbols on Products and Materials and more information.
You can see the product name and model on the product label. The label can be found on the back of the device.
R10 is used for illustrations here unless otherwise specified. The actual product prevails.

II Wireless Extension

I Product Introduction
The extender supports both wireless and wired extension. Choose the extension type as required and refer to the following instructions for configuration.

Wireless Extension

AP Mode

Extension The extender connects to the upstream router

Type

through Wi-Fi and extends the router’s Wi-Fi

coverage range

The extender connects to the upstream router through an Ethernet cable and converts the router’s wired network to Wi-Fi

Scenario Rooms requiring Wi-Fi coverage without Ethernet cables deployed

Rooms requiring Wi-Fi coverage with Ethernet cables deployed

Features

After successful wireless extension, the dead zone will be covered by Wi-Fi, and the Ethernet port can be used to provide wired network access for other devices such as set-top boxes, computers, and TVs.

After successful wired extension (AP Mode), high-speed and stable Wi-Fi access can be provided for various wireless such as smartphones, tablets, and smart devices.

WPS/RESET WPS/RESET

Wireless Extension

Wired Extension

1. Select the extender location
Place the extender midway between the router and the Wi-Fi dead zone to ensure stable signal reception and effective area coverage.

Good signal, high speed

Router

Extender
Recommended Installation: Place the extender midway between the router and the Wi-Fi dead zone.

WPS/RESET WPS/RESET
WPS/RESET WPS/RESET

2. Set Up the Extender

Method 1: Via Smartphone Web Browser (Recommended)

1 Connect the smartphone to the Wi-Fi of the extender: Tenda_EXT. When the web UI of the extender is displayed automatically, tap Start Now.
Thanks for Choosing Tenda WiFi Range Extender
Faster, Safer, Smoother, Smarter

2 Select the Wi-Fi to be extended, which is the router’s Wi-Fi.

Your working mode has been detected as: Wireless Extension

Switch

Select the Wi-Fi to be extended

Start Now

Tenda_XXXXXX

2.4G

Tips
· If not automatically redirected to the extender’s web UI, start a browser and enter re.tenda.cn in the address bar.
If configuring through a smartphone, disable mobile data
and try to log in. · If your smartphone displays the prompt The WLAN
“Tenda_EXT” is not connected to the Internet. Select
Use Without Internet, and continue using this Wi-Fi. · If Unsecured Network prompts on the page, ignore it.

The extension is completed. Follow the onscreen instructions.

Extended Successfully
Once the extension is successful, wait until the Wi-Fi reboots in about 20 seconds, connect to the new Wi-Fi and enter the password to access the internet.

2.4G

Extender Info
Wi-Fi Name Tenda_XXXXXX_EXT
Wi-Fi Password
XXXXXXXX Management Address
re.tenda.cn Management Password
XXXXXXXX
*It is recommended to take a screenshot to save Wi-Fi information

Method 2: Via WPS Button
Tips · Ensure that the encryption used by the router’s Wi-Fi
includes WPA-PSK or WPA2-PSK. · The WPS design may differ with different manufacturers.
If this method fails, use another method to configure.
1 Press the WPS button of the router for about 1 to 3 seconds to enable its WPS function.
2 Within 2 minutes, press the WPS button on the extender for about 1 to 3 seconds, and its indicator blinks green fast. When the LED indicator is solid on, the setup is successful. The extender’s Wi-Fi name is “Upstream router Wi-Fi name _EXT,” and the Wi-Fi password is the same as the upstream router.
2 1
Within 2 minutes

3 Enter the Wi-Fi password of the router, and tap Next.
Wireless Extension
Upstream Wi-Fi Name Tenda_XXXXXX Upstream Wi-Fi Password ········

Cancel

4 Set the Wi-Fi name, Wi-Fi password and management password of the extender as required. If nothing changes, tap Next.

Wireless Extension

*Extender network settings. If nothing changes, tap Next.

Add New Wi-Fi

Use upstream Wi-Fi name/password

Extender Wi-Fi Name Tenda_XXXXXX

Extender Wi-Fi Password XXXXXXXX

Set Wi-Fi password to the management password

Cancel

III AP Mode

1 Ensure that the Ethernet cable has been deployed in the place that needs Wi-Fi coverage and can access the internet normally. Connect the Ethernet cable to the Ethernet port of the extender, and plug the extender into the power socket. The indicator changes from blinks green to solid on to indicate successful extension.

Tips · If not automatically redirected to the extender’s web UI,
start a browser and enter re.tenda.cn in the address bar.
If configuring through a smartphone, disable mobile data
and try to log in. · If your smartphone displays the prompt The WLAN
“Tenda_EXT” is not connected to the Internet. Select
Use Without Internet, and continue using this Wi-Fi. · If Unsecured Network prompts on the page, ignore it.

Tips If the deployed Ethernet cable is for wiring in the wall, prepare the Ethernet cable by yourself.

3 Set the Wi-Fi name, Wi-Fi password and management password of the extender as required, and tap Next.

Wired Extension

Ethernet cable
2 Connect the smartphone to the Wi-Fi network of the extender: Tenda_EXT. When the web UI of the extender is displayed automatically, tap Start Now.

Your working mode has been detected as:

Wireless Extension

Switch

Extender Wi-Fi Name Tenda_EXT

Extender Wi-Fi Password Please enter

Set Wi-Fi password to the management password

Cancel

V Connect Clients to the Internet

Appearance

WPS/RESET WPS/RESET

Wi-Fi Name: Wi-Fi name you set, Tenda_EXT, router’s Wi-Fi name_EXT, or the same as the router

Wi-Fi Password: Wi-Fi password you set or same as the router

Wireless clients (such as a smartphone)

Printer

Smart TV

Camera

Computer

Wired clients (Only wireless extension mode can be connected, if
using AP mode, connect with Wi-Fi)

FAQ
Q1. The internet speed poor when connected to the extender’s Wi-Fi. What should I do? A1. – The extender may be improperly positioned. · If placed too far from the dead zone, the extender’s Wi-Fi cannot cover the area, leaving no signal in the dead zone. · If placed too far from the router, the extender cannot receive a stable Wi-Fi signal to extend. – Reposition the extender midway between the router and the dead zone for optimal performance.

Too far from the dead zone (Not recommended)

Midway (Recommended)

Too far from the router (Not recommended)

Router

Extender

Q2. I cannot log in to the web UI of the extender. What should I do? A2. First, try the following solutions: – Visit http://re.tenda.cn in your browser. – If you are using a wireless client, such as a smartphone, ensure that the Mobile Data (if any) function is disabled. If the problem persists, try the following solutions: Before extension: – If you are using a wireless client, such as a smartphone, ensure that your smartphone has connected to the Wi-Fi
network of the extender: Tenda_EXT. – If you are using a wired device, such as a computer, ensure that your computer is set to Obtain an IP address
automatically and Obtain DNS server address automatically. – Reset the extender by referring to Q6 in the FAQ, and log in again.
Safety Precautions
Before operating, read and follow these precautions to prevent accidents. – Do not use the device in a place where wireless devices are not allowed. – Clean only with dry cloth. – Do not block any ventilation openings, such as newspapers, table-cloth, curtains. – To avoid electrical shocks, do not insert any object into the ventilation openings. – Unplug this device during lightning storms or when unused for long periods of time. – The mains plug is used as the disconnect device, which shall remain readily operable. – The power socket shall be installed near the device and easily accessible. – Operating environment: Temperature: 0 – 40 (32 – 104); Humidity: (10% – 90%) RH, non-condensing; Storage environment:
Temperature: -40 – 70 (-40 – 158); Humidity: (5% – 90%) RH, non-condensing. – If such phenomena as smoke, abnormal sound or smell appear when you use the device, immediately stop using it and disconnect its
power supply, and contact the after-sales service personnel. – Warning: To reduce the risk of electric shock, do not remove cover as there are no user-serviceable parts inside. Refer servicing to
qualified personnel. – Refer all servicing to qualified service personnel. – Disconnect the power source during servicing. – Keep this device out of reach of children to prevent children from using it as a toy and causing personal injury. – Keep the device away from water, fire, high electric field, high magnetic field, and inflammable and explosive items. For the latest safety precautions, see Safety and Regulatory Information on www.tendacn.com.

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. The device is for indoor usage only. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the device and your body. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Operating frequency: 2412-2462MHz NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
NOM
LA OPERACIóN DE ESTE DISPOSITIVO ESTA SUJETA A LAS SIGUIENTES CONDICIONES: a) Es posible que este equipo o dispositivo no cause interferencia perjudicial. b) Este equipo o dispositivo debe aceptar cualquier tipo de interferencia, incluyendo la que pueda causar su operación no deseada. Estimado usuario: Antes de utilizar este producto lo invitamos a leer el siguiente manual para que conozca todas sus funciones y caracteristicas.

Producto
Alimentador de Energía: Alimentación: 100V – 240V ca 50Hz/60Hz, 0.3A Salida: 9V cc 0.6A PAIS DE ORIGEN: CHINA

NOMBRE DEL PRODUCTO: Repetidor Wi-Fi N300 MODELO: R10/T10

Reset button and WPS button · Press 1-3s for WPS · Press 8s for reset
Ethernet port Used to connect to such devices as routers, computers, game consoles, TV, set-top boxes, printers, and so on.

Scenario Status

Network extension

Solid on Blinking green fast

Blinking red slowly

Start up

Solid green for 15 seconds Blinking green slowly

Internet connection

Blinking yellow slowly

Reset

Blinking yellow fast

Description
Extension success – Green: Proper position. – Yellow: Fair position. Move the extender closer to the router. – Red: Too far from the router. WPS extension Failed to extend (Check whether the Wi-Fi name/password of the upstream router is correct or place the extender close to the router)
Power on and starting up Startup complete Failed to connect to the internet (Check whether the upstream router can access the internet normally) Restoring the extender to factory settings

After extension: – If you are using a wireless client, such as a smartphone, ensure that your smartphone has connected to the
Wi-Fi network of the extender. If the Wi-Fi name of the extender is the same as the upstream router, stand nearby the extender and connect to its Wi-Fi network (the extender should not be too close to the router, or temporarily power off the router). – If you are using a wired device, such as a computer, ensure that your computer is set to Obtain an IP address automatically and Obtain DNS server address automatically.
Q3. My extender cannot find the Wi-Fi network of my router. What should I do? A3. Try the following solutions: – The extender is single-band (2.4 GHz only). It can only bridge 2.4 GHz Wi-Fi. Please ensure that your router’s
2.4 GHz Wi-Fi is enabled. – Ensure that your smartphone is near the extender and can search and connect to the Wi-Fi of the router. – Change the channel of your router, and try again. – Change the encryption type of the router to WPA-PSK or WPA2-PSK, and try again.
Q4. I cannot find the Wi-Fi name of the extender after extending network successfully (the indicator is solid on). What should I do? A4. The possible reason is that you did not customize the extender Wi-Fi name when extending the network. In this case, the Wi-Fi name of the extender is the same as the upstream router or _EXT of the upstream router Wi-Fi name after the extension is successful.
Q5. After the wireless extension is successful (the indicator is solid on), the network speed through the extender is slower than when directly connected to the router. What should I do? A5. The network speed may decrease during wireless extension due to upstream signal attenuation, but this is a normal phenomenon that does not affect normal use. To maximize the extension effect, ensure that the extender indicator is solid green, and reduce the obstacles between the extender and the router.
Q6. How to reset the extender? A6. When the extender completes startup, press the RESET button for about 8 seconds. When the indicator blinks yellow fast, the extender is restored to factory settings.

CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This equipment should be installed and operated with a minimum distance 20cm between the device and your body. NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable. Declaration of Conformity Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the device (Extender) is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: https://www.tendacn.com/download/list-9.html Operating Frequency/Max Output Power

English: Operating Frequency/Max Output Power Italiano: Frequenza operativa/Potenza di uscita massima Français: Fréquence de fonctionnement/Puissance de sortie maximale Español: Frecuencia operativa/Potencia de salida máxima Deutsch: Betriebsfrequenz/Max. Ausgangsleistung Polski: Czstotliwo pracy /Maksymalna moc wyjciowa Nederlands: Bedrijfsfrequentie/Maximaal uitgangsvermogen Cestina: Provozní frekvence/maximální výstupní výkon Român: Frecvena de funcionare/Puterea maxim de ieire Português: Frequência de Funcionamento/Potência Máxima de Saída Svenska: Driftsfrekvens/Max Uteffekt

Slovencina: Prevádzková frekvencia/maximálny výstupný výkon

Magyar: Mködési frekvencia/Maximális kimeneti teljesítmény

: /

Eesti: Töösagedus/Max väljundvõimsus

Dansk: Driftsfrekvens/Maks. Udgangseffekt

Suomi: Toimintataajuus/maksimilähtöteho

Hrvatski: Radna frekvencija/Maksimalna izlazna snaga

Latviesu: Operjoss frekvences/Maksiml jauda

Lietuvi: Darbinis daznis /maksimali isjimo galia

Slovenscina: Delovna frekvenca/Najvecja izhodna moc

Türkçe: Çalima Frekansi/Maks. Çiki Gücü

: /.

2412MHz-2472MHz/20dBm

IC
CAN ICES-3 (B) / NMB-3 (B) Canadian Compliance Statement This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le onjunc areil est conforme aux CNR d’ l’innovation, la science et le développement économique Canada licables aux areils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’areil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, onj si le brouillage est susceptible d’en compromettre le fonctionnement. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Tous les changements ou modifications non expressément approuvée par le responsible de la conformité pourrait vider l’utilisateur est habilité à exploiter l’équipemen. ISEDC Radiation Exposure Statement: The equipment complies with ISEDC RF radiation exposure limits set forth for an uncontrolled environment. Cet appareil est conforme aux limitesd’exposition de rayonnement RF ISEDC établiespour un environnement non contrôlé. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

RECYCLING This product bears the selective sorting symbol for Waste Electrical and Electronic Equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
Technical Support Shenzhen Tenda Technology Co., Ltd. Floor 6-8, Tower E3, No.1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052 Website: www.tendacn.com E-mail: support@tenda.com.cn
support.us@tenda.cn (North America) support.uk@tenda.cn (United Kingdom)
Copyright © 2025 Shenzhen Tenda Technology Co.,Ltd.All rights reserved. Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other brand and product names mentioned herein are trademarks or registered trademarks of their respective holders.Specifications are subject to change without notice.
V1.0 Keep for future reference

Documents / Resources

Tenda R10, T10 N300 Wi-Fi Range Extender [pdf] Installation Guide
R10, T10, R10 T10 N300 Wi-Fi Range Extender, R10 T10, N300 Wi-Fi Range Extender, Wi-Fi Range Extender, Range Extender, Extender

References

User Manual

Tenda R10, T10 N300 Wi-Fi Range Extender Installation Guide

R10, T10 N300 Wi-Fi Range Extender

Product Information

Specifications:

Product Usage Instructions

Wireless Extension (AP Mode)

Wired Extension (AP Mode)

Installation Steps:

1. Select the Extender Location:

2. Set Up the Extender:

Extender Info:

Frequently Asked Questions (FAQ)

Q: How can I find the Wi-Fi name and password after setup?

Q: What should I do if the WPS setup method fails?

Documents / Resources

References

Leave a comment

Cancel reply