tectake-LOGO

tectake 403000 Electric Table Frame Piotr

tectake-403000-Electric-Table-Frame-Piotr-PRODUCT

Specifications:

Column Number Maximum Load Speed Input Voltage Lowest Position Highest Position Desktop Size Duty Cycle Applicable Temperature
2 70KG 25mm/s 100-240V 710mm 1210mm 1000-1600mm (width) 500-800mm (depth) Continuous operation for 2 mins at most after pause for 18mins

Product Usage Instructions

Step 1: Install Pedestal
Follow the installation guide provided in the manual. Use the specified tools and parts listed in the accessory and part list.

Step 2: Install Supporting Beam
Adjust the support beam size according to the table top size. Use the wrench to tighten the screws.

Step 3: Install Transmission Rod
Do not rotate the drive rod more than a third of a turn. Follow the provided pictures and use the wrench to tighten the screws.

Step 4: Install Supporting Plate
Ensure the distance between desktop edge and supporting plate is no more than 200mm. Tighten the screws using the specified wrench.

Step 5: Install Control Box and Handswitch
Connect all cables onto the control box. Use the provided tools to tighten the screws as instructed.

Step 6: Connect All Cables onto the Control Box
Follow the cable connection instructions provided in the manual to ensure proper installation.

How to Use Handswitch:
The handswitch features different buttons for adjusting the desk height. Refer to the LED display for height positions and use the corresponding buttons for adjustment.

FAQ

Fault Phenomenon:
If you encounter any of the following issues, refer to the common fault treatment section in the manual or contact your supplier for assistance:

  1. No response while pressing up arrow/down arrow after connecting to power supply.
  2. Rising in a low speed or motor not moving as instructed.
  3. Desk going down but not up, downward sliding, or frequent repositioning.
  4. Overwork issues related to duty cycle (Max 2min on/18min off).

DIMENSION

tectake-403000-Electric-Table-Frame-Piotr-FIG- (1)

Technical data

tectake-403000-Electric-Table-Frame-Piotr-FIG- (2)

Accessory list

Attention: The drawings below are only for reference which might be slightly different from the actual object, please in kind prevail. Any tools missing or installation problems, please contact the customer service firstly.

tectake-403000-Electric-Table-Frame-Piotr-FIG- (3)

Part list

tectake-403000-Electric-Table-Frame-Piotr-FIG- (4)

Installation instruction

tectake-403000-Electric-Table-Frame-Piotr-FIG- (5)

STEP1
Install Pedestal(1)

tectake-403000-Electric-Table-Frame-Piotr-FIG- (6)

STEP2
Install Supporting beam(4)

tectake-403000-Electric-Table-Frame-Piotr-FIG- (7)

tectake-403000-Electric-Table-Frame-Piotr-FIG- (8)

Lay Column(2) down, just like picture 1 shows, then install (4), use wrench(C) to tighten the screws(B). Install Column(3) just as picture 2 shows.

STEP3
Install Transmission rod(5)

tectake-403000-Electric-Table-Frame-Piotr-FIG- (9)

STEP4
Install Supporting plate(6)

tectake-403000-Electric-Table-Frame-Piotr-FIG- (10)

STEP5
Install Control box (7) and Handswitch(9)

tectake-403000-Electric-Table-Frame-Piotr-FIG- (11)

Install Baffle (8)

tectake-403000-Electric-Table-Frame-Piotr-FIG- (12)

Install(8), use 2.5*2.5 wrench(D) to tighten the screws(E).

STEP6
Connect All the Cables onto the Control Box(7)

tectake-403000-Electric-Table-Frame-Piotr-FIG- (13)

Use the cable tie(11) to fix all the connection cables on the desk to keep it clean.

How to use handswitch

Button

tectake-403000-Electric-Table-Frame-Piotr-FIG- (14)

Bottom introduction: There are seven buttons that “tectake-403000-Electric-Table-Frame-Piotr-FIG- (15)“, “‘tectake-403000-Electric-Table-Frame-Piotr-FIG- (16)” , “1”, “2”, “З”, “М”, “А”

  1. tectake-403000-Electric-Table-Frame-Piotr-FIG- (15)” : Adjust the desk upwards
  2. tectake-403000-Electric-Table-Frame-Piotr-FIG- (16)” : Adjust the desk downwards
  3. “1” : Position 1, first height position saved by the user
  4. “2” : Position 2, second height position saved by the user
  5. “3” : Position 3, third height position saved by the user
  6. “M” : Height memory function
  7. “A” : Alert button to remind users changing posture

Instruction

Height Adjustable Function:
Press the” tectake-403000-Electric-Table-Frame-Piotr-FIG- (15)” or “tectake-403000-Electric-Table-Frame-Piotr-FIG- (16)” button to adjust the height. The LED display shows the current height.

Height Memory Function:

  • Press UP or DOWN button and adjust the height to the desired height. Press “M” to save the height, and the screen will display “5-“; Press “1”, “2” ,or “3” then, that is, save the height to the corresponding position 1 or 2 or 3, which will show in the display screen as “5-1″ ,”5-2”, or “5-3”;
  • Press “1”, “2” and “3” button directly to automatically adjust the memory height you saved.

Reminder Function:

  • Press REMINDER button “A” to activate the function. The LED display shows ” tectake-403000-Electric-Table-Frame-Piotr-FIG- 19
  • Two seconds later, press the “tectake-403000-Electric-Table-Frame-Piotr-FIG- (15)” or “tectake-403000-Electric-Table-Frame-Piotr-FIG- (16)” button to adjust the reminder time only when the display screen flashes. The default time of the reminder is 45 minutes, which is shown as ” =45″. Then press any button to save the time setup, or wait 5 seconds and system will save the time setup automatically. During the countdown, any operation will lead to a repeat starting of the timer. When the countdown finishes, display screen will show “tectake-403000-Electric-Table-Frame-Piotr-FIG- 20” the buzzer will be active with a 10-second “DiDi…DiDi…DiDi” tone.
  • Within the 10-second reminder buzz, press any button to reactivate the time countdown that is set up in (b) step. If no operation during the 10-second reminder buzz, there will be another reminder buzz after 5 minutes. No operation during the second buzz will turn off the Long-Time Sitting Reminder.
  • Press and hold the “A” button for three seconds to turn off the Long-Time Sitting Reminder. The LED display shows ” OFF “

Troubleshooting

  • Reset: When the LED shows”tectake-403000-Electric-Table-Frame-Piotr-FIG- 21“, press “tectake-403000-Electric-Table-Frame-Piotr-FIG- (16)” button until the desk reaches its lowest height and rebounds to stop, it means the reset has been finished.
  • When it does’t work and the LED shows “E01” or “E02”, please retry 18 mins later.
  • If the “tectake-403000-Electric-Table-Frame-Piotr-FIG- (16)” button does’t work, please check the cable connection and then cut off the power for at least 10 seconds. Reconnect to the power and press “tectake-403000-Electric-Table-Frame-Piotr-FIG- (16)” button to start the reset process when it shows the “tectake-403000-Electric-Table-Frame-Piotr-FIG- 21 “.
  • If all these above process are inefficient, plz contact our customer service.

Common fault treatment

The following tips will help you detected and eliminate common fault and error.
If the fault you met is not listed below, please contact with your supplier. Only the manufacturer and professionals are capable for investigating and correcting those fault and error.

tectake-403000-Electric-Table-Frame-Piotr-FIG- (17)

Attention

  1. Power supply: AC100V-240V,50/60HZ
  2. Service Environment: 0-40°C
  3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet dishcloth when cleaning, be careful not to let the drops into the internal parts, not loose the connector.
  4. The electric box contains electronic components, metals, plastics, wires etc., so dispose of it in accordance with each country’s environmental legislation, not the general household waste.
  5. Check carefully to ensure correct and complete assembly before using.
  6. Be familiar with all functions and program settings of the product before first use.
  7. Children are forbidden to play on the product because of unforeseen action when playing, so any dangerous consequences caused by this improper action will not be on
  8. Slight noise caused by the V-ribbed belt or brake system due to structure will not have any effect on the use of the equipment.
  9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure that the cleaner used will not pollute the environment.
  10. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
  11. Cleaning and user maintenance shall not be made by children without supervision.
  12. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid a hazard.
  13. Please make sure there is no hazard sources in your operating environment. e.g., do not litter the tools around. Always be careful to treat the packaging materials in order to avoid any possible danger, e.g. plastic bag may lead to choking hazard to children.
  14. Keep the original package of the equipment if necessary in case of the future use in transportation.

Waste disposal

tectake-403000-Electric-Table-Frame-Piotr-FIG- (18)

This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable re use of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

Contact Person
TecTake Ltd
18 Soho Square
London W1D 3QL
United Kingdom
Telephone: +44 203 488 4565
mail@tectake.co.uk

Documents / Resources

tectake 403000 Electric Table Frame Piotr [pdf] Instruction Manual
402999, 403000, 403000 Electric Table Frame Piotr, 403000, Electric Table Frame Piotr, Table Frame Piotr, Frame Piotr

References

Leave a comment

Your email address will not be published. Required fields are marked *