TARAMPS TLC3000 RF Remote Controller Instruction Manual

Dimensions Receiver Base (WxHxD): 54 x 17 x 46mm / 2.13 x 0.67 x 1.81
Transmitter – Control (LxWxD): 36.5 x 11.5 x 76.5mm / 1.44 x 0.45 x 3.01

Weight Base Receiver: 0.1Kg / 0.22lb
Transmitter – Control: 0.1Kg / 0.22lb

Product Usage Instructions

Installation and Setup

Before starting, ensure you have all the package contents listed in the manual.

Follow the steps provided in the manual to install and set up the TLC 3000 LONG-RANGE REMOTE CONTROL.

Volume Control

To enable the VOLUME key repeat cancellation feature, press the and keys simultaneously. The red LED will indicate activation.

Battery Replacement

If the LED indicator stays lit for 3 seconds after pressing any key, it’s time to replace the battery. Follow the instructions to replace the battery with a new one of the same type.

Synchronization

Follow the SYNC/LEARN instructions provided in the manual to synchronise your remote control with the receiving base.
Note: You can cancel the configuration by pressing the SYNC/LEARN key twice.

Memory Mode Chart

Refer to the memory mode chart for functions related to changing folders in a USB flash drive. Choose the corresponding model and follow the step-by-step guide on page 05 of the manual.

Introduction

Please read this manual carefully before making any connections or using the product. If you have any questions, please contact our technical support team at 1832664050 or www.taramps.com.br.
The TLC 3000 LONG-RANGE REMOTE CONTROL can be adapted to most CD and DVD players on the market.

A high-tech product that operates using radio frequency (RF), emulating the basic functions of your device’s original infrared remote control over long distances.
It features encrypted codes that prevent signal copying and retransmission.

Package contents

Before installing your product, check the contents inside the package.
1 – Control (Transmitter)

1 – Receiving Base
1 – 4-way cable already connected
1 – Custom Cord Taramps
1 – Protective case (Only for colour series).
Refer to the purchased product label.

Knowing the transmitter

Transmission indicator LED and battery
Increase volume (+)
Decrease volume (-)
Previous track
Next track
Play / Pause key
Power key and multi-function
Folder up
Folder down
Strap for Cord

Cancelling the increased volume repeat (+)

For the protection of the sound system, your control has a cancellation of the VOLUME (+) key repeat.
In this case, when you press the button, the sound volume will only increase by one level. one level.
Press the () () keys simultaneously to activate this function. The red LED will be on for 2 seconds and will turn off. To return to the function, repeat the operation.

Replacing the battery

Your controller will alert you when the battery needs to be replaced.
If the LED indicator remains lit for 3 seconds after pressing any key, your battery needs to be replaced.

To replace the battery, simply unlock the bottom and top of the controller with an object or key inserted into the side slot. Then replace the dead battery with a new one in the same position, observing the correct polarity.

Knowing the receiving base

Infrared sensor
SYNC/LEARN configuration key

LED signal reception indicator
Antenna
Power input (+12V and GND)

Infrared transmitter

Getting the best performance out of the product

To obtain the maximum performance of the product (range, ease of configuration and quality), we recommend observing the following indications.

When fixing the Receiver Base, make sure that the antenna is not curled or pointing to another opposite location from which you will most use the Transmitter Control. Always leave it vertically.

Make sure that the infrared transmitter is pointed directly at the CD / DVD Player of your vehicle.
It is advisable not to fix the Receiver Base in glasses in which they have films, as it may damage them if you need to remove the product from the place. Try to install on insulated surfaces and away from metal plates or other metal surfaces that can absorb or reflect (fade) the RF signals.
Once the installation is performed, when it is necessary to use the control with the need of wide range, there must be a line (without obstacles) between the two products.
- Walls, trees and metal structures can also attenuate or cause RF signal failure and consequently reduce the range of the device.
Momentary failures may occur if the battery is low. Check the Control if the LED indicator is indicating “low battery”.
- In this case, the LEDs of the receiving base and control will be on for 3 seconds after pressing any key. It is recommended to replace a new CR2032 battery.
- See battery replacement illustration on the previous page.

Installations

After fixing the Receiver Base to a location of your choice, connect the positive (+ 12V) power cables to the positive terminal of the battery and the negative (GND) to the negative terminal of the battery.

It is recommended for safety the use of 1 Amp fuse in the positive cable with a maximum distance of 30cm from the battery.
Position the Infrared so that it is toward the panel of your Head Unit.

Ready!

Now, we need to configure your Control so that the receiver sends the signals correctly to your Player.
Note: This product is already set up for the Pioneer CD Player models.
If your Head Unit is of another brand, use the table to configure the MEMORY MODE, because in this mode, there are compatibilities with various models of Head Units on the market.

If your device is not listed in the table, you will need to use LEARN MODE. See this explanation.

Setting – Memory mode

Caution: Do not approximate the Receiver Base closer than 30cm, as it may not work properly due to the high sensitivity of the product.

Configuration complete. Make sure that the product is properly controlling your head Unit.
Note: It is possible to cancel the configuration at any time by pressing the SYNC/LEARN key twice.

Setting – Learn mode

Learn Mode one function: In this case, the key will have only one function copied from the original control.
For this, use the short press (click).
Learn Mode two functions: In this case, the key will have two functions copied from the original control, the first function being recorded for short press and the second function for long press.

Setting – Synchronising (Up to 3 Controls)

The TLC-3000 is already factory-synchronised. If you need to synchronise more controls by losing the original or to have more controls registered on the receiving base, follow the setup procedures below.
Setup finished. Check that the receiver base LED is blinking by pressing the control keys, indicating synchronisation is ok.

Note:. You can cancel the configuration at any time by pressing the SYNC/LEARN key 3x.

Memory mode chart

RESET CODE: Clears memory. It can be used optionally before loading the codes by the LEARN process.

Functions used to change the folder in the USB flash drive.
Based on the chart, choose the model corresponding to your device and press the key combinations.
Follow the step-by-step.

Technical features

Power Supply
- Receiver Base:6 ~16VDC
- Transmitter (Control): 3V CR2032 Battery

Consumption
- Receiver Base: 30mA (max.)
- Transmitter (Control): 7mA CR2032 Battery
- Modulation: OOK
- Frequency: 433.92 MHz
- Maximum Power: +10dBm

Dimensions
- Receiver Base (WxHxD): 54x x x 46mm /2.13″ x 0.67″ x 1.81″|
- Transmitter-Control (LxWxD): 36.5 x 11.5 x 76.5mm / 1.44″ x 0.45″ x 3.01″

Weight
- Base Receiver: 0.1Kg /0.22lb
- Transmitter -Control: 0.1Kg Kg/ 0.22lb

This equipment is not entitled to protection against harmful interference and must not cause interference in duly authorised systems.
See FCC declaration on the next page.
Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference,
This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Disposal

At the end of its useful life, this product must not be disposed of in household waste. Look for an electronic equipment collection or recycling centre for proper disposal.

Term of warranty

TARAMPS, located at Julio Budisk highway, SN, KM 30 – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-120, warrants this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause in it improper or inadequacy as to the purpose for which it was produced 12 months from the date of purchase. In case of defect during the warranty period, TARAMPS’ responsibility is limited to the repairing or replacement of the device of its own making.

This warranty excludes:

Damaged products by improper installation, water infiltration, or violation by unauthorised individuals;
Tamper or torn warranty seal;

Cases in which the product is not used in adequate conditions;
Defects caused by accessories, modifications or features attached to the product;
The product with damage from falling, bumps or nature-related problems (flooding, lightning, etc);

The warranty card is not properly filled out or torn.
Costs involving uninstallation, reinstallation of equipment, as well as the shipment to the factory;
Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.

CUSTOMER SERVICE

Technical assistance

For international support, check on our website: www.taramps.com.br/en/rede-de-assistencias-tecnicas or contact directly the factory support.
Phones: +551832664050 /+5518997493391

E-mail: service@taramps.com.br
Manufactured by:
TARAMPS ELECTRONICS LTDA TAX ID: 11.273.485/0001-03

Highway Júlio Budisk, SN, KM 30 Alfredo Marcondes – SP
Made in Brazil
+55 18 3266-4050

www.taramps.com.br

Frequently Asked Questions

How do I know when to replace the battery?

If the LED indicator remains lit for 3 seconds after pressing any key, it's time to replace the battery.

Can I cancel the synchronisation process?

Yes, you can cancel the configuration at any time by pressing the SYNC/LEARN key twice.

Documents / Resources

TARAMPS TLC3000 RF Remote Controller [pdf] Instruction Manual
2BQGR-TLC, 2BQGRTLC, TLC 3000, TLC3000 RF Remote Controller, TLC3000, RF Remote Controller, Remote Controller, Controller

References

User Manual

TARAMPS TLC3000 RF Remote Controller