CF40 Wi-Fi 6 Router
User Guide
This guide provides instructions for setting up, connecting, and configuring your NetComm CF40 Wi-Fi 6.
GET TO KNOW YOUR NERCOMM CF40 WIFI 6
Top View of Device
LED Indicator Lights
This lights represent the working state and connectivity of the NetComm Wi-Fi 6 Gateway
Green = connected
Red = disconnected
Bottom View of Device
Wi-Fi 6 Gateway Label
Contains your Wi-Fi network name and Wi-Fi password. You’ll need these to connect your devices to Wi-Fi.
Back View of Device
| Button/Connection Port | Description |
| Power Button | Turns the NetComm CF40 Wi-Fi 6 on or off. |
| DC IN Point | Connection point for the included power adapter to connect to the power supply. |
| Ethernet WAN Port | Connect to your Network Termination Device (NTD) for high-speed internet access. Covers fixed line technologies such as nbn™ FTTP, HFC, FTTC and Fixed Wireless. |
| Ethernet LAN Port | Connect your Ethernet based devices (E.g., computers, servers, modems, Wi-Fi routers, switches, and other network devices) to one of these ports for high-speed internet access. |
SETTING UP YOUR NERCOMM CF40 WIFI 6
Step 1: Power on the NetComm CF40 Wi-Fi 6
- Plug the device power adapter into a wall socket.
- Press the power button on the NetComm CF40 Wi-Fi 6 and wait a few minutes for it to start up.
- The power LED indicator will appear green on the top of the NetComm CF40 Wi-Fi 6 if it is on and operating correctly.
Step 2: Connect your NetComm CF40 Wi-Fi 6
Depending on your nbn™ technology type, your NetComm CF40 Wi-Fi 6 will connect differently. If you are unsure of your nbn™ technology type, it is listed in your nbn™ ordered email.
| If your NBN connection is: | Instructions: |
| Hybrid Fibre Coaxial (HFC) Fibre to the Premises (FTTP) Fibre to the Curb (FTTC) or Fixed Wireless |
Connect the ethernet cable from the WAN port on the NetComm CF40 Wi-Fi 6 to the UNI-D port on your nbn™ connection box. Note: Wait for the lights on the nbn™ connection box to turn blue (this may take up to 15 minutes). |
Step 3: Connect your devices to Wi-Fi
- Using your device, scan the QR code on the label and/or Wi-Fi Security Card and select “Join Wi-Fi Network” if prompted.
- Alternatively, on your device scan for and select the Wi-Fi Network Name and enter the password outlined on the label and/or WIFI Security Card to connect.
CONFIGURING YOUR NERCOMM CF40 WIFI 6
Note: This is only needed if you have factory-reset your modem/router. Otherwise, Tangerine has pre-configured hardware specifically for your service and this step is not required.
If you have factory-reset your device or purchased from an alternative retailer, please follow these easy steps to access the configuration page of your NetComm CF40 Wi-Fi 6.
- Push the power button on the back of the NetComm CF40 Wi-Fi 6 to turn it on. Wait a few minutes for it to complete starting up.
- Connect to the NetComm CF40 Wi-Fi 6 using Wi-Fi or an Ethernet cable to the yellow LAN port.
- Open a web browser and type https://192.168.20.1 into the address bar, then press Enter.
- At the login screen, type in the username and password printed on the label on the bottom of the NetComm CF40 Wi-Fi 6 and click the login button.
- Select ‘Basic Setup’ from the menu on the left-hand side of the screen to begin set up.
- Select ‘PPPoE’ as your WAN setting connection type
- Enter your SSID and password. Note: SSID is your unique network name that appears when you scan for nearby wireless networks. You can choose and create your own network name.
- Select your applicable ‘Time Zone Offset’ and ‘Daylight Saving Time’ setting.
- Review the summary page that will appear and select the ‘Save’ button to complete the setup.
OTHER INFORMATION ABOUT YOUR NERCOMM CF40 WIFI 6
Product Warranty
NetComm offers a two (2) year warranty on fixed broadband products commencing from the date of purchase. For more information read NetComm’s T&Cs here.
Wi-Fi Analytics Platform
The CloudMesh Wi-Fi Analytics Platform is a fully integrated solution that provides visibility into the health of each individual Wi-Fi home network. It creates superior end-user experiences by enabling proactive diagnostic, management, and control of the home Wi-Fi environment, helping resolve even the most elusive Wi-Fi problems.
Wi-Fi Autopilot
Every NetComm CF40 Wi-Fi 6 includes the CloudMesh Wi-Fi AutoPilot. Wi-Fi AutoPilot constantly scans and analyses your Wi-Fi network environment and if any detrimental changes are detected, the Wi-Fi AutoPilot adjusts the NetComm CF40 Wi-Fi 6’s Wi-Fi parameters. Any action taken is based on a patented and weighted algorithm ensuring the internet connection experience is never compromised. It ensures that every Wi-Fi client device is connected on the best possible channel, using the fastest available band, at the perfect RF power level, utilizing the closest Wi-Fi access point.
Need support?
For a more comprehensive user guide, you can view the NetComm User Guide here.
Alternatively, for Customer Service and troubleshooting, contact our team on 1800 211 112.
Documents / Resources
 |
TANGERINE NetComm CF40 Wi-Fi 6 Router [pdf] User Guide NetComm CF40 Wi-Fi 6 Router, NetComm CF40, Wi-Fi 6 Router, Router |
