Sensor.JPG

T-LED 069383 Microwave Sensor RF Switch and Dimmer Owner’s Manual

T-LED 069383 Microwave Sensor RF Switch and Dimmer.jpg

 

 

069383 dimLED MRS 2v1 Sensor
Microwave Sensor RF Switch & Dimmer

  • Active microwave motion detectors with HF system 10.525GHz, motion can be detected through plastic, glass and thin non-metal materials.
  • Built-in motion sensor and daylight sensor.
  • Powered by low voltage 9-24VDC, output RF 2.4G signal.
  • Matched with RF LED controller or RF dimmable LED driver use.
  • Detection area, time delay and daylight threshold can be set via knob potentiometer for each specific application.
  • Three sensing switch modes can be selected by set button: non-dimming sensing switch, two-step dimming sensing switch, and constant illumination sensing switch.
  • Wide detection area, range up to 20m in diameter.
  • Support higher mounting height 15m Max.

 

Dimension

FIG 1 Dimension.JPG

 

Technical Parameters

FIG 2 Technical Parameters.JPG

 

Sensing switch type setting

Press hold the Set key 5s: Set as non-dimming sensing switch, the LED indicator flash 2 times.
Press hold the Set key 10s: Set as two-step dimming sensing switch, the LED indicator flash 4 times.
Press hold the Set key 15s: Set as constant illumination sensing switch, the LED indicator flash 6 times.

 

Microwave Sensor Detection Pattern

FIG 3 Microwave Sensor Detection Pattern.JPG

 

Typical application 1: used as a non-dimming sensing switch

Turns on the light upon detection of motion, and turns off after a pre-selected hold time when there is no movement.

FIG 4 used as a non-dimming sensing switch.JPG

 

Setting on this demonstration:

FIG 5 Setting on this demonstration.JPG

 

Typical application 2: used as a sensing switch with two-step dimming

Turns on the light upon detection of motion, after a pre-selected hold time, dim to 20% brightness, and turns off after a pre-selected stand-by time when there is no movement.

FIG 6 used as a sensing switch with two-step dimming.JPG

 

FIG 7 used as a sensing switch with two-step dimming.JPG

 

Typical application 3: used as a constant illumination sensing switch

Turns on the light and dim up to expected brightness level upon detection of motion, and turns off after a pre-selected hold time when there is no movement.

FIG 8 used as a constant illumination sensing switch.JPG

 

Setting on this demonstration:

FIG 9 Setting on this demonstration.JPG

 

 

Microwave Sensor User recommended settings

FIG 10 Microwave Sensor User recommended settings.JPG

 

Match Remote Control (two match ways)

The microwave motion sensor RF switch must be matched with one or multiple RF LED controller or RF dimmable LED driver, including single color, dual color, RGB, RGBW, RGB+CCT or switch light type, turn on or turn off light by motion detection.

End user can choose the suitable match/delete ways. Two options are offered for selection:

Use the controller’s Match key

Match:
Short press match key on the controller firstly, immediately press match key on the sensor.
The LED indicator on th controller fast flash a few times means match is successful.

Delete:
Press and hold match key on the controller for 5s to delete all match,
The LED indicator fast flash a few times means match were deleted.

Use Power Restart

Match:
Switch off the power of the RF controller or LED driver, then switch on power, repeat again, immediately short press the match key on the sensor.
The light blinks 3 times means match is successful.

Delete:
Switch off the power of the RF controller or LED driver, then switch on power, repeat again, immediately long press the match key 2s on the sensor.
The light blinks 5 times means match is deleted.

 

Microwave Application Notice

  1. The sensor is designed for indoor use only.
    The raining or wind blowing may trigger the microwave sensor even if without human motion when outdoor use.
  2. The sensor should be installed by a professional electrician. please turn off the power before installing, wiring and changing setting of the knob.
  3. The distance between any two sensors should be at least 3m to avoid interference each other.
  4. When the microwave sensor is installed in a metal lighting fixture or space with large reflector, for example a warehouse with metal roof, the microwave signal
    will be reflected and cause the lights permanent illuminated even if without motion signal. Please reduce the detection area to solve the problems.
  5. Make sure the sensor not close to or be blocked by high density materials, such as metal, glass, concrete walls etc.
    The materials will reduce or block microwave signal and cause false trigger.
  6. The sensor which installed in the plastic and glass lampshade will reduce th sensitivity.
    For every 3mm increase in thickness, the sensitivity will reduced by 20%.
  7. The light sensitivity threshold is in a sunny environment, no shadow and ambient light diffuse reflection.
    Ambient lux level could be different in different environment, weather, climate, time-of-delay and season.
  8. Make sure there are no fans, DC motor, or other vibrating objects in installation area. The movement will trigger sensor as well.

 

Read More About This Manual & Download PDF:

Documents / Resources

T-LED 069383 Microwave Sensor RF Switch and Dimmer [pdf] Owner's Manual
069383, dimLED MRS 2v1, 069383 Microwave Sensor RF Switch and Dimmer, Microwave Sensor RF Switch and Dimmer, Sensor RF Switch and Dimmer, Switch and Dimmer

References

Leave a comment

Your email address will not be published. Required fields are marked *