Origins®
SLC9612PP
Two Handle Centerset Lavatory Faucet
Operation & Maintenance Manual
Model Numbers
SLC9612PP Two handle centerset lavatory faucet with A Push Pop Drain Assembly
Compliance
– ASME A112.18.1/CSA B125.1
– NSF/ANSI/CAN 61: Q<1, NSF/ANSI 372
– Water Sense 1.0 gpm (3.8 L/min)
Certified by IAPMO R&T
WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Feature Highlights
- 4″ mount
- Quarter turn ceramic cartridges
- 1/2″ IPS inlet connections
- 1.0 gpm (3.8 L/min) standard flow rate
- Components shall be metal and nonmetallic construction
- Plated in standard polished chrome finish
Warranty
Limited Lifetime – to the original end purchaser in consumer/residential installations.
10 Years – for commercial/industrial installations. Refer to www.symmons.com/warranty for complete warranty information.
Dimensions
Measurements
| E | Deck Thickness Ref. Max. 1-1/4″, 32 mm |
| G | (2x) Hole Size Min. Ø 1-1/8″, 29 mm Max. Ø 1-1/4″, 32 mm |
| L | 1/2-14 NPSM |
Note: Dimensions subject to change without notice.
Parts Breakdown
Replacement Parts
| Item | Description | Part Number |
| B D | (2x) Handle Kit | RL-220* |
| E | Hot Cartridge | RL-222H |
| F | Cold Cartridge | RL-222C |
| H | Aerator | RL-240-1.5* (1.5) RL-240-1.0* (1.0) RL-240-0.5* (0.5) |
| I J | Mounting Hardware | RL-221 |
| K | Push Pop Drain Assembly | RL324* |
*Note: Append -STN to part number for Satin Nickel finish.
Tools Required
| Adjustable wrench |  |
| Allen wrench (3/32″) |  |
| Plumber putty |  |
| Plumber tape |  |
Installation
If replacing an older faucet ensure water supply is turned OFF before removing, then turn faucet control valve ON to relieve water pressure.
DO NOT use pipe dope or thread sealant on drain assembly, or any plastic threaded components.
1) Insert faucet body (G) through mounting gasket (I) and sink holes.
2) Install mounting nuts (J) onto 1/2″ IPS inlet connections on faucet body (G). Using a wrench, finish with one-half turn. DO NOT overtighten.
3) Push Pop Install: Insert drain body (L) into drain opening. From below, Tighten locking nut (O) with gasket (M) and washer (N) to flange. Tighten tail nut (Y) with washer (X) to secure tail pipe (Q). DO NOT overtighten.
- Plumbers Putty
4) Attach supply lines to 1/2″ IPS inlet connections on faucet body (G). Using a wrench, finish with one half turn. DO NOT overtighten.
5) Attach supply lines to shut-off valves and hand tighten. Using a wrench, finish with one-half turn. DO NOT overtighten.
6) Remove aerator (H) and flush lines free of debris. Check for leaks.
Maintenance
1) Turn off water. Loosen and remove handle set screw (D), handle (B), nut (C) and old cartridge (E or F).
2) Correctly align new cartridge (E or F) and insert into faucet body (G). Install and secure nut (C).
3) Replace handle (B) and reinstall set screw (D). Tighten set screw.
Troubleshooting Chart
| Finish is spotting. | Elements in water supply may cause water staining on finish. | Clean finished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse with water. |
Symmons Industries, Inc. • 31 Brooks Drive • Braintree, MA 02184 • Phone: 800-796-6667 • Fax: 800-961-9621
Copyright © 2023 Symmons Industries, Inc. • symmons.com • gethelp@symmons.com • ZV-3716 REV B • 072423
Documents / Resources
 |
SYMMONS SLC9612PP 4 Centerset Faucet with Push Pop Faucet [pdf] Instruction Manual SLC9612PP 4 Centerset Faucet with Push Pop Faucet, SLC9612PP, 4 Centerset Faucet with Push Pop Faucet, Faucet with Push Pop Faucet, Push Pop Faucet, Pop Faucet |
 |
SYMMONS SLC9612PP 4 Centerset Faucet with Push Pop Faucet [pdf] User Guide SLC9612PP 4 Centerset Faucet with Push Pop Faucet, SLC9612PP, 4 Centerset Faucet with Push Pop Faucet, Faucet with Push Pop Faucet, Push Pop Faucet, Pop Faucet, Faucet |
