Mfumo wa Boardcon CM3576 kwenye Moduli
Vipimo
- Kipengele: CM3576
- CPU: Quad-core Cortex-A72 na quad-core Cortex-A53
- RDD: 2GB LPDDR4/x (hadi 8GB)
- eMMC: 32GB (hadi 128GB chaguo)
- MWELEKEO UFS: FLASH Power EDP/MIPI DSI I2S MIPI CSI SATA HDMI pato la DP pato la RGB Pato la EBC Flex Bus
- Vipimo: 1-CH EDP, 1-CH MIPI DSI, 5-CH, 3-CH, 4-Lane au 4-CH, 2-Lane + 1-CH, 4-Lane CSI (hadi Kamera 5 za CSI), 2-CH , 1-CH (chaguo la EDP), chaguo la 1-CH, 1-CH, 24bit, 1-CH (chaguo)
- UNAWEZA: 2-CH
- USB: 1-CH Aina-C na 1-CH USB Host3.0
- Ethaneti: 1-ch 1GB PHY
- Kipimo cha Bodi: 57.5 x 44mm
Maagizo ya Matumizi ya Bidhaa
Taratibu za Kuweka
- Unganisha ingizo la nguvu linalohitajika kulingana na Ufafanuzi wa Pini.
- Hakikisha mfumo voltage iko ndani ya safu maalum (3.4V-5.5V).
- Ikiwa unatumia vifaa vya pembeni kama vile kamera au skrini, viunganishe kwenye milango inayofaa kwenye ubao.
Taarifa za Usalama
Kila mara tumia ujazo wa nguvu uliobainishwatage mbalimbali ili kuepuka kuharibu ubao au vijenzi.
Kutatua matatizo
Ukikumbana na matatizo yoyote wakati wa kusanidi au kufanya kazi, rejelea sehemu ya utatuzi wa mwongozo kwa mwongozo.
Maswali Yanayoulizwa Mara kwa Mara
- Swali: Nifanye nini ikiwa bodi haina nguvu juu ya?
J: Angalia miunganisho ya nishati na uhakikishe sautitage iko ndani ya safu maalum. Tatizo likiendelea, rejelea sehemu ya utatuzi wa mwongozo. - Swali: Je, ninaweza kuboresha uwezo wa DDR?
J: Ndiyo, uwezo wa DDR unaweza kuboreshwa hadi 8GB kulingana na vipimo vilivyotajwa.
Mwongozo wa Mtumiaji wa Marejeleo wa CM3576
V1.20240628
Muundo Uliopachikwa wa Boardcon
www.armdesigner.com
Utangulizi
Kuhusu Mwongozo huu
Mwongozo huu unakusudiwa kumpa mtumiaji nyongezaview ya bodi na faida, vipimo kamili vya vipengele, na kuweka taratibu. Ina taarifa muhimu za usalama pia.
Maoni na Usasishaji wa Mwongozo huu
Ili kuwasaidia wateja wetu kufaidika zaidi na bidhaa zetu, tunaendelea kufanya rasilimali za ziada na zilizosasishwa zipatikane kwenye Boardcon webtovuti (www.boardcon.com, www.armdesigner.com).
Hizi ni pamoja na miongozo, madokezo ya programu, programu za zamaniamples, na programu iliyosasishwa na maunzi. Ingia mara kwa mara ili kuona ni nini kipya!
Tunapotanguliza kazi kwenye rasilimali hizi zilizosasishwa, maoni kutoka kwa wateja ndio ushawishi mkuu, Ikiwa una maswali, maoni, au wasiwasi kuhusu bidhaa au mradi wako, tafadhali usisite kuwasiliana nasi kwa support@armdesigner.com.
Udhamini mdogo
Boardcon inaidhinisha bidhaa hii kutokuwa na kasoro katika nyenzo na utengenezaji kwa muda wa mwaka mmoja kuanzia tarehe ya kununuliwa. Katika kipindi hiki cha udhamini Boardcon itarekebisha au kubadilisha kitengo chenye hitilafu kwa mujibu wa mchakato ufuatao:
Nakala ya ankara asili lazima ijumuishwe wakati wa kurejesha kitengo chenye hitilafu kwa Boardcon. Udhamini huu mdogo hautoi madhara yanayotokana na mwanga au kuongezeka kwa nguvu nyingine, matumizi mabaya, matumizi mabaya, hali isiyo ya kawaida ya uendeshaji, au majaribio ya kubadilisha au kurekebisha utendakazi wa bidhaa.
Udhamini huu ni mdogo kwa ukarabati au uingizwaji wa kitengo chenye kasoro. Kwa hali yoyote Boardcon haitawajibika au kuwajibika kwa hasara au uharibifu wowote, ikijumuisha, lakini sio mdogo kwa faida yoyote iliyopotea, uharibifu wa bahati mbaya au matokeo, upotezaji wa biashara, au faida inayotarajiwa inayotokana na matumizi au kutoweza kutumia bidhaa hii.
Matengenezo yanafanywa baada ya kumalizika kwa muda wa udhamini hutegemea malipo ya ukarabati na gharama ya usafirishaji wa kurudi. Tafadhali wasiliana na Boardcon ili kupanga huduma yoyote ya ukarabati na kupata maelezo ya malipo ya ukarabati.
Utangulizi wa CM3576
Muhtasari
Mfumo wa CM3576 kwenye moduli umewekwa na RK356 ya Rockchip ina quad-core Cortex-A72 na kichakataji cha quad-core Cortex-A53, Iliyopachikwa Mali-G52 MC3 GPU na 6.0 TOPs NPU.
Imeundwa mahususi kwa ajili ya vifaa vya utendaji wa juu kama vile mfumo wa ufuatiliaji wa video wa 4K, vifaa vya kukokotoa vya AI Edge, vifaa mahiri vya mwingiliano, kompyuta za kibinafsi na roboti. Uchakataji wa utendakazi wa hali ya juu wa uchakataji wa media titika na suluhu ya injini ya kuongeza kasi inaweza kusaidia wateja kutambulisha teknolojia mpya kwa haraka zaidi na kuongeza ufanisi wa jumla wa suluhisho.
Vipengele
- Microprocessor
- Quad-core Cortex-A72 hadi 2.2GHz
- Quad-core Cortex-A53 hadi 1.8GHz
- 48KB I-cache 32KB D-cache na 1MB L2 kwa A72 kila msingi, 32KB I-cache 32KB D-cache na 512KB L2 kwa A53 kila msingi.
- 6.0 TOPS Kitengo cha Mchakato wa Neural
- Mali-G52 MC3 hadi 1.0GHz
- Quad-core Cortex-M0 kwa matumizi ya mtumiaji
- Shirika la Kumbukumbu
- LPDDR4 au LPDDR4X RAM hadi 16GB
- EMMC hadi 128GB
- Inasaidia UFS hadi 128GB
- Kusaidia FSPI Flash
- Anzisha ROM
- Inaauni upakuaji wa msimbo wa mfumo kupitia USB OTG
- Mfumo salama
- Imepachikwa injini mbili za misimbo
- Kusaidia ngazi ya ufunguo ili kuhakikisha ufunguo salama
- Kusaidia mfumo salama wa uendeshaji na uchakataji data
- Inasaidia OTP
- Kisimbuaji/Kisimbaji cha Video
- Inaauni usimbaji wa video hadi 8K@30fps
- Inaauni H.265 kusimba hadi 8K@30fps au 4K@120fps
- H.264 HP inasimba hadi 4K@60fps
- Ukubwa wa picha hadi 65520 x 65520
- Onyesha mfumo mdogo
- Pato la Video
- Inaauni HDMI 2.1 TX na ARC, hadi kiolesura cha 4K@120fps Au EDP TX hadi 4K@60Hz
- HDMI 2.1 inasaidia hali ya FRL
- Inaauni njia 4 za MPI DSI hadi 4K@60Hz
- Inaauni kiolesura cha PD1.4a hadi 4K@60fps
- Inasaidia pato la RGB 24bit
- Inasaidia kiolesura cha skrini ya E-wino
- Ingizo la Video/Picha
- Inaauni miingiliano ya 3-CH MIPI 4lanes CSI au njia 4 za 2-CH MIPI + 1-CH 4 miingiliano ya CSI
- Inaauni ingizo la DVP 8-bit
- Sauti
- Miingiliano mitano ya I2S/PCM
- Inatumia 8-ch TX/RX kwenye I2S0/1
- Inatumia safu ya Maikrofoni Hadi kiolesura cha 8ch PDM/TDM
- Inatumia pato la 2-ch SPDIF
- Inatumia pembejeo ya 2-ch SPDIF
- Inasaidia utambuzi wa shughuli za sauti
- USB / PCIE/SATA3
- Miingiliano miwili ya USB2.0 OTG
- Violesura vya Aina moja ya C au DP
- Mpangishi mmoja wa USB3.0 au kiolesura cha PCIE2.1×1 au SATA3.
- Kiolesura kimoja cha PCIE2.1×1 au SATA3.
- SATA3 inaweza kutumia vifaa vitano kwa kila mlango kupitia swichi ya PM
- Ethaneti
- Kwenye bodi RTL8211F/ YT8531
- I2C
- Hadi 9-CH I2C
- Kusaidia hali ya kawaida na hali ya haraka (hadi 400kbit / s)
- I3C
- Hadi 2-CH I3C
- Inasaidia hali ya HDR (hadi 30Mbps)
- I2C inalingana
- SDIO / SDMMC
- Saidia itifaki ya SDIO 3.0
- Msaada wa kadi ya SD3.0
- SPI
- Hadi vidhibiti 5-ch SPI,
- Kiolesura kamili cha upatanishi cha duplex
- UART
- Inasaidia hadi UART 12
- UART2 iliyo na waya 2 za utatuzi
- Imepachikwa FIFO mbili za 64byte
- INAWEZA
- Inasaidia hadi vidhibiti viwili vya CAN
- Inasaidia itifaki ya CAN FD
- ADC
- Hadi chaneli mbili za ADC
- Ubora wa biti 12 hadi 1MS/ssampkiwango cha ling
- Voltage ingizo mbalimbali kati ya 0V hadi 1.8V
- PWM
- Hadi PWM 4 zenye uendeshaji unaotegemea kukatizwa
- Msaada 32bit wakati / kituo cha kaunta
- Kitengo cha nguvu
- PMU RK806 kwenye ubao
- 3.4 ~ 5.5V ingizo la nguvu kuu
- 1.8V na 3.3V upeo wa pato 500mA
- RTC ya chini sana hutumia mkondo wa sasa, chini ya 5uA kwa kitufe cha 3V.
Mchoro wa CM3576 Block
Mchoro wa RK3576 Block
Bodi ya Maendeleo (EM3576) Mchoro wa Block
Vipimo vya CM3576
| Kipengele | Vipimo |
| CPU | Quad-core Cortex-A72 na quad-core Cortex-A53 |
| DDR | 2GB LPDDR4/x (hadi 8GB) |
| eMMC FLASH | 32GB (hadi 128GB) |
| UFS FLASH | chaguo |
| Nguvu | DC 3.4 ~ 5.5V |
| EDP/MIPI DSI | 1-CH EDP, 1-CH MIP DSI |
| I2S | 5-CH |
| MPI CSI | 3-CH 4-Lane au 4-CH 2-Lane + 1-CH 4-Lan CSI (hadi Kamera 5 za CSI) |
| SATA | 2-CH |
| Pato la HDMI | 1-CH (chaguo la EDP) |
| Pato la DP | 1-CH |
| Pato la RGB | 1-CH 24bit |
| Pato la EBC | 1-CH (chaguo) |
| Basi la Flex | chaguo |
| Kipengele | Vipimo |
| INAWEZA | 2-CH |
| USB | 1-CH Aina-C na 1-CH USB Host3.0 |
| Ethaneti | 1-ch 1GB PHY |
| SDMMC | 2-CH |
| SPDIF TX | 2-CH |
| SPDIF RX | 2-CH |
| I2C | 9-CH |
| I3C | 2-CH |
| SPI | 5-CH |
| INAWEZA | 2-CH |
| UART | 11-CH, 1-CH(DEBUG) |
| PWM | 4-CH |
| ADC IN | 2-CH |
| Vipimo vya Bodi | 57.5 x 44mm |
Kipimo cha CM3576 PCB
Ufafanuzi wa Pini ya CM3576
| Bandika | Mawimbi | Maelezo au vitendaji | GPIO mfululizo | IO Voltage |
| 1 | VCC_SYS | Uingizaji wa Nguvu ya Mfumo | 3.4V-5.5V | |
| 2 | VCC_SYS | Uingizaji wa Nguvu ya Mfumo | 3.4V-5.5V | |
| 3 | VCC_SYS | Uingizaji wa Nguvu ya Mfumo | 3.4V-5.5V | |
| 4 | PWRON_L | Ingizo la Ufunguo wa Nguvu | 3.4V-5.5V | |
| 5 | VCC_3V3_S3 | 3.3V GPIO Pato la Nguvu | Upeo wa 500mA | 3.3V |
| Bandika | Mawimbi | Maelezo au vitendaji | GPIO mfululizo | IO Voltage |
| 6 | UART0_TX_M0 | Kwa chaguo-msingi la utatuzi | GPIO0_D4_u | 3.3V |
| 7 | UART0_RX_M0 | Kwa chaguo-msingi la utatuzi | GPIO0_D5_u | 3.3V |
| 8 | GND | Ardhi | 0V | |
| 9 | WEKA UPYA_L | GPIO0_A1_z imeunganishwa(PU) | 1.8V | |
| 10 | SDMMC0_DET_L_1V8 | (PU100K) | GPIO0_A7_u | 1.8V |
|
11 |
WIFI_WAKE_HOST_H
_1V8 |
I2C0_SCL_M0 |
GPIO0_B0_z |
1.8V |
|
12 |
BT_WAKE_HOST_H_1
V8 |
I2C0_SDA_M0 |
GPIO0_B1_z |
1.8V |
|
13 |
HOST_WAKE_BT_H_1 V8 |
SPDIF_TX1_M2/SPI2_CLK_ M1/PDM0_CLK1_M2/CLK1_
32K_OUT/SATA_MPSWIT |
GPIO1_D5_d |
1.8V |
|
14 |
SAI2_SCLK_M0_1V8 |
I3C0_SDA_PU_M1/UART10
_RX_M1 |
GPIO1_D1_d |
1.8V |
| 15 | SAI2_SDO_M0_1V8 | UART10_TX_M1 | GPIO1_D0_d | 1.8V |
|
16 |
SAI2_SDI_M0_1V8 |
I3C0_SDA_M1/PWM1_CH4_
M1 |
GPIO1_D3_d |
1.8V |
|
17 |
SAI2_LRCK_M0_1V8 |
I3C0_SCL_M1/PWM1_CH3_
M1 |
GPIO1_D2_d |
1.8V |
|
18 |
WIFI_REG_ON_H_1V8 |
I2C8_SCL_M1/UART2_TX_ M0/PDM0_SDI0_M2/SATA_
CPPOD |
GPIO1_C6_d |
1.8V |
|
19 |
BT_REG_ON_H_1V8 |
I2C8_SDA_M1/UART2_RX_
M0/PDM0_SDI1_M2/SATA_ CPDET |
GPIO1_C7_d |
1.8V |
|
20 |
UART4_CTSN_M1_1V
8 |
SDMMC1_DET_M0/I2C6_S
DA_M1/SPI2_CSN0_M1 |
GPIO1_C3_u |
1.8V |
|
21 |
UART4_RTSN_M1_1V 8 |
SDMMC1_PWEN_M0/I2C6_ SCL_M1/SPI2_CSN1_M1/P
WM1_CH2_M1 |
GPIO1_C2_u |
1.8V |
|
22 |
UART4_TX_M1_1V8 |
SPI2_MOSI_M1/UART2_RT
S_M0/PCIE0_BUTTONRST |
GPIO1_C4_d |
1.8V |
| 23 | UART4_RX_M1_1V8 | SPI2_MISO_M1/UART2_CT
S_M0/PCIE1_BUTTONRST |
GPIO1_C5_d | 1.8V |
| 24 | SDMMC1_D1_M0_1V8 | I2C9_SCL_M1/SPI1_MOSI_
M0/PCIE1_WAKE_M1/SAI3_ LRCK_M1/PWM1_CH1_M1 |
GPIO1_B5_d | 1.8V |
| 25 | SDMMC1_D0_M0_1V8 | I2C9_SDA_M1/SPI1_CLK_M 0/PCIE1_CLKREQ_M1/SAI3
_SCLK_M1/PWM1_CH0_M1 |
GPIO1_B4_d | 1.8V |
| Bandika | Mawimbi | Maelezo au vitendaji | GPIO mfululizo | IO Voltage |
|
26 |
SDMMC1_D2_M0_1V8 |
UART3_CTS_M2/SPI1_MIS O_M0/PCIE0_CLKREQ_M1/
SAI3_SDO_M1 |
GPIO1_B6_d |
1.8V |
|
27 |
SDMMC1_D3_M0_1V8 |
UART3_RTS_M2/SPI1_CSN 0_M0/PCIE0_WAKE_M1/SAI
3_SDI_M1 |
GPIO1_B7_d |
1.8V |
|
28 |
SDMMC1_CMD_M0_1 V8 |
UART3_TX_M2/SPI1_CSN1
_M0/PDM0_SDI2_M2/PWM0 _CH0_M1 |
GPIO1_C0_d |
1.8V |
|
29 |
SDMMC1_CLK_M0_1V
8 |
UART3_RX_M2/PDM0_CLK
0_M2/SAI3_MCLK_M1 |
GPIO1_C1_d |
1.8V |
| 30 | GND | Ardhi | 0V | |
|
31 |
RECOVERY_SARADC
_VIN1 |
KUPONA
MODE/ADC_IN1(PU10K) |
1.8V |
|
| 32 | SARADC_VIN2 | ADC_IN2 | 1.8V | |
| 33 | GND | Ardhi | 0V | |
|
34 |
SDMMC0_CLK |
I3C1_SDA_PU_M1/I2C5_SC
L_M0/UART5_TX_M2/SPI0_ CLK_M1/SAI3_SCLK_M3 |
GPIO2_A5_d/FSPI1_CLK_M0 |
3.3V |
|
35 |
SDMMC0_D1 |
DSM_ALN_M0/I2C8_SDA_M 0/UART0_TX_M1/UART7_T X_M2/SPI0_MISO_M1/CAN0
_TX_M0/SAI3_MCLK_M3 |
GPIO2_A1_d/ PWM2_CH3_M0/ FSPI1_D1_M0 |
3.3V |
|
36 |
SDMMC0_D0 |
DSM_ALP_M0/I2C8_SCL_M 0/UART0_RX_M1/UART7_R X_M2/SPI0_MOSI_M1/CAN0
_RX_M0 |
GPIO2_A0_d/ PWM2_CH2_M0/ FSPI1_D0_M0 |
3.3V |
|
37 |
SDMMC0_CMD |
I2C5_SDA_M0/UART5_RX_ M2/SPI0_CSN0_M1/SAI3_S
DO_M3 |
GPIO2_A4_d/ PWM2_CH4_M0/
FSPI1_CSN0_M0 |
3.3V |
|
38 |
SDMMC0_D3 |
I3C1_SDA_M1/DSM_ARN_ M0/UART5_CTSN_M2/SAI3
_SDI_M3/CAN1_TX_M0 |
GPIO2_A3_d/
FSPI1_D3_M0/ JTAG_TMS_M0 |
3.3V |
|
39 |
SDMMC0_D2 |
I3C1_SCL_M1/DSM_ARP_M
0/UART5_RTSN_M2/SAI3_L RCK_M3/CAN1_RX_M0 |
GPIO2_A2_d/
FSPI1_D2_M0/ JTAG_TCK_M0 |
3.3V |
|
40 |
LCDC_DEN/EBC_SDL E/DSMC_DATA0 |
I2C3_SCL_M2/UART5_RX_ M0/SPI3_CLK_M1/SAI1_SDI
1_M1/FLEXBUS1_D1 |
GPIO3_D4_d |
3.3V |
|
41 |
LCDC_VSYNC/EBC_S DCLK/DSMC_CLKN |
UART5_CTS_M0/SPI3_MOS
I_M1/SAI1_SDI3_M1/FLEXB US1_CLK/PWM2_CH6_M3 |
GPIO3_D6_d |
3.3V |
| Bandika | Mawimbi | Maelezo au vitendaji | GPIO mfululizo | IO Voltage |
|
42 |
LCDC_HSYNC/EBC_G DCLK/DSMC_CLKP |
I2C3_SDA_M2/UART5_TX_ M0/SPI3_MISO_M1/SAI1_S
DI2_M1/FLEXBUS1_D0 |
GPIO3_D5_d |
3.3V |
|
43 |
LCDC_CLK/EBC_SDO E/DSMC_RESETN |
UART5_RTS_M0/SPI3_CSN 1_M1/SAI4_SCLK_M1/FLEX BUS1_D12_M0/FLEXBUS0_ D15_M0/FLEXBUS1_CSn_M
1/CAM_CLK0_OUT_M0 |
GPIO3_D7_d/ PWM2_CH7_M3 |
3.3V |
|
44 |
DSMC_INT0/GPIO4_A 0_d |
I2C7_SCL_M2/UART3_TX_ M0/SPI1_CSN1_M2/SAI4_L RCK_M1/FLEXBUS1_D14_ M0/FLEXBUS0_D13_M0/FL EXBUS1_CSn_M3/CAM_CL
K1_OUT_M0 |
GPIO4_A0_d/ MIPI_TE_M2/ SPDIF_RX0_M1 |
3.3V |
|
45 |
DSMC_INT2/GPIO4_A 1_d |
I2C7_SDA_M2/UART3_RX_ M0/SAI4_SDO_M1/FLEXBU S1_D13_M0/FLEXBUS0_D1 4_M0/FLEXBUS0_CSn_M1/
CAM_CLK2_OUT_M0 |
GPIO4_A1_d/ VO_POST_EMPTY/ SPDIF_TX0_M1 |
3.3V |
|
46 |
PHY1_LED1/CFG_LD
O0 |
Kasi ya LED (PD4.7K) |
3.3V |
|
|
47 |
PHY1_LED2/CFG_LD
O1 |
Unganisha LED(PD4.7K) |
3.3V |
|
| 48 | PHY1_MDI0+ | 0.5V | ||
| 49 | PHY1_MDI0- | 0.5V | ||
| 50 | PHY1_MDI1+ | 0.5V | ||
| 51 | PHY1_MDI1- | 0.5V | ||
| 52 | PHY1_MDI2+ | 0.5V | ||
| 53 | PHY1_MDI2- | 0.5V | ||
| 54 | PHY1_MDI3+ | 0.5V | ||
| 55 | PHY1_MDI3- | 0.5V | ||
| 56 | 32KOUT_RTC_1V8 | Pato la RTC_CLK 32.768KHz | GPIO0_A2_d | 1.8V |
| 57 | VCC_RTC | Ingizo la Nguvu ya RTC | 1.8~3.3V | |
|
58 |
LCDC_D0/EBC_SDDO 0/DSMC_CSN0 |
I3C1_SCL_M2/UART2_CTS
_M2/SAI2_SDO_M2/FLEXB US1_D2 |
GPIO3_D3_d/ PWM2_CH5_M3 |
3.3V |
|
59 |
LCDC_D1/EBC_SDDO 1/DSMC_CSN3 |
I3C1_SDA_M2/UART2_RTS
_M2/SPI4_CSN1_M1/SAI2_ SDI_M2/FLEXBUS0_D12/FL EXBUS0_CS_M3/FLEXBUS 1_D15_M0 |
GPIO3_D2_d/ PWM2_CH4_M3 |
3.3V |
| Bandika | Mawimbi | Maelezo au vitendaji | GPIO mfululizo | IO Voltage |
|
60 |
LCDC_D2/EBC_SDDO 2/DSMC_CSN2 |
I3C1_SDA_PU_M2/SPI4_CL K_M1/SAI2_MCLK_M2/FLEX BUS0_D11/FLEXBUS1_CS_
M2 |
GPIO3_D1_d |
3.3V |
|
61 |
LCDC_D3/EBC_SDDO 3/DSMC_DATA1 |
UART8_CTS_M0/SPI1_CSN 0_M2/SAI1_MCLK_M1/FLEX
BUS1_D3 |
GPIO3_D0_d/ PWM2_CH3_M3 |
3.3V |
|
62 |
LCDC_D4/EBC_SDDO 4/DSMC_DATA2 |
UART8_RTS_M0/SPI1_CLK
_M2/SAI1_SCLK_M1/FLEXB US1_D4 |
GPIO3_C7_d |
3.3V |
|
63 |
LCDC_D5/EBC_SDDO 5/DSMC_DATA3 |
UART8_TX_M0/SPI1_MOSI
_M2/SAI1_LRCK_M1/FLEXB US1_D5 |
GPIO3_C6_d |
3.3V |
|
64 |
LCDC_D6/EBC_SDDO 6/DSMC_DATA4 |
UART8_RX_M0/SPI1_MISO
_M2/SAI1_SDO0_M1/FLEXB US1_D6 |
GPIO3_C5_d/ PWM2_CH2_M3 |
3.3V |
|
65 |
LCDC_D7/EBC_SDDO 7/DSMC_DATA5 |
I2C5_SCL_M3/UART11_TX_ M0/SPI2_CSN0_M2/SAI1_S DO0_M1/FLEXBUS1_D7/CA
N0_TX_M3 |
GPIO3_C4_d |
3.3V |
|
66 |
LCDC_D8/EBC_SDDO 8/DSMC_INT3 |
I2C9_SDA_M3/UART11_CT S_M0/SPI4_MOSI_M1/SAI2_ LRCK_M2/FLEXBUS0_D10/
FLEXBUS0_CSN_M2 |
GPIO3_C3_d/ PWM2_CH1_M3 |
3.3V |
|
67 |
LCDC_D9/EBC_SDDO 9/DSMC_INT1 |
I2C9_SCL_M3/UART11_RTS
_M0/SPI4_MISO_M1/SAI2_S CLK_M2/FLEXBUS0_D9 |
GPIO3_C2_d/ PWM2_CH0_M3 |
3.3V |
|
68 |
LCDC_D10/EBC_SDD O10/DSMC_DATA6 |
I2C5_SCL_M3/UART11_RX_ M0/SPI2_MISO_M2/SAI1_S DO2_M1/FLEXBUS1_D8/CA
N0_RX_M3 |
GPIO3_C1_d |
3.3V |
|
69 |
LCDC_D11/EBC_SDD O11/DSMC_DATA7 |
I2C4_SCL_M3/UART2_TX_ M2/UART3_RTS_M1/SAI1_S
DO3_M1/FLEXBUS1_D9 |
GPIO3_C0_d |
3.3V |
|
70 |
LCDC_D12/EBC_SDD O12/DSMC_DQS0 |
I2C4_SDA_M3/UART2_RX_ M2/UART3_CTS_M1/SAI1_S DO0_M1/FLEXBUS1_D10/F
LEXBUS1_CSN_M0 |
GPIO3_B7_d |
3.3V |
|
71 |
LCDC_D13/EBC_SDD
O13/DSMC_DQS1 |
SPI3_CSN0_M1/ETH0_TXC
LK_M0/FLEXBUS0_CLK |
GPIO3_B6_d/
PWM0_CH1_M3 |
3.3V |
|
72 |
LCDC_D14/EBC_SDD O14/DSMC_DATA8 |
UART9_CTS_M1/ETH0_TX D0_M0/SPDIF_TX1_M0/FLE
XBUS0_D0 |
GPIO3_B5_d/ PWM1_CH5_M3 |
3.3V |
| Bandika | Mawimbi | Maelezo au vitendaji | GPIO mfululizo | IO Voltage |
|
73 |
LCDC_D15/EBC_SDD O15/DSMC_DATA9 |
UART9_RTS_M1/ETH0_TX D1_M0/SPDIF_RX1_M0/FLE
XBUS0_D1 |
GPIO3_B4_d/ PWM1_CH4_M3 |
3.3V |
|
74 |
LCDC_D16/EBC_SDC E0/DSMC_DATA10 |
I2C8_SCL_M3/UART9_TX_ M1/ETH0_TXCTL_M0/PDM1
_SDI0_M2/FLEXBUS0_D2 |
GPIO3_B3_d |
3.3V |
|
75 |
LCDC_D17/EBC_SDC E1/DSMC_DATA11 |
I2C8_SDA_M3/UART9_RX_ M1/ETH0_RXD0_M0/PDM1_
SDI1_M2/FLEXBUS0_D3 |
GPIO3_B2_d |
3.3V |
|
76 |
LCDC_D18/EBC_SDC E2/DSMC_DATA12 |
UART10_TX_M0/SPI4_CSN 0_M1/ETH0_RXD1_M0/PDM
1_CLK0_M2/FLEXBUS0_D4 |
GPIO3_B1_d/ PWM1_CH3_M3 |
3.3V |
|
77 |
LCDC_D19/EBC_SDC E3/DSMC_CSN1 |
UART10_RX_M0/SPI2_MOS I_M2/ETH0_MCLK_M0/SAI4
_MCLK_M1/FLEXBUS0_D8 |
GPIO3_B0_d/ PWM0_CH0_M3 |
3.3V |
|
78 |
LCDC_D20/EBC_VCO M/DSMC_DATA13 |
UART10_RTS_M0/UART1_T X_M2/ETH0_RXCTL_M0/PD
M1_CLK1_M2/FlexBUS0_D5 |
GPIO3_A7_d |
3.3V |
|
79 |
LCDC_D21/EBC_GDO E/DSMC_DATA14 |
UART10_CTS_M0/UART1_ RX_M2/ETH0_MDC_M0/PD
M1_SDI2_M2/FlexBUS0_D6 |
GPIO3_A6_d/ PWM1_CH2_M3 |
3.3V |
|
80 |
LCDC_D22/EBC_GDS P/DSMC_DATA15 |
SPI2_CSn1_M2/UART1_RT S_M2/ETH0_MDIO_M0/PDM
1_SDI3_M2/FlexBUS0_D7 |
GPIO3_A5_d/ PWM1_CH1_M3 |
3.3V |
|
81 |
LCDC_D23/EBC_SDS HR/DSMC_RDYN |
SPI2_CLK_M2/UART1_CTS
_M2/ETH0_CLKOUT_25M_ M0/SAI4_SDI_M1/FlexBUS1 _D11/FlexBUS0_CSn_M0 |
GPIO3_A4_d/ PWM1_CH0_M3 |
3.3V |
|
82 |
TYPEC_DPTX_AUX_P
UPDCTL1 |
AUPLL_CLKIN_M2/SAI1/4_
MCLK_M0 |
GPIO4_A2_d
/PWM2_CH5_M0 |
3.3V |
|
83 |
PCIE1_CLKREQn_M2 |
I2C2_SDA_M2/UART5_CTS
_M1/SPI4_CS1_M2/SAI1_LR CK_M0/FlexBUS1_D12_M1 |
GPIO4_A5_d |
3.3V |
|
84 |
PCIE1_PWREN_H |
I2C2_SCL_M2/UART5_RTS
_M1/SPI3_CS0_M2/SAI1_S CLK_M0/FlexBUS1_CS_M4 |
GPIO4_A3_d/ PWM2_CH4_M1 |
3.3V |
|
85 |
HDMI_TX_ON_H |
I2C4_SDA_M1/UART6_RX_ M0/SPI3_MISO_M2/SAI4_L RCK_M0/PDM1_CLK0_M1/F
lexBUS1_D14_M1/CAN0_RX _M2 |
GPIO4_A6_d |
3.3V |
| Bandika | Mawimbi | Maelezo au vitendaji | GPIO mfululizo | IO Voltage |
|
86 |
TYPEC_DPTX_AUX_P UPDCTL2 |
I2C4_SCL_M1/UART6_TX_ M0/SPI3_MOSI_M2/SAI4_S CLK_M0/PDM1_SDI3_M1/Fl exBUS1_D13_M1/CAN0_TX
_M2 |
GPIO4_A4_d |
3.3V |
|
87 |
HP_CTL_H |
SPI3_CLK_M2/SAI4_SDI_M
0/SAI1_SDO0_M0 |
GPIO4_A7_d/
PWM2_CH6_M0 |
3.3V |
|
88 |
I2C3_SCL_M0_Sensore |
PCIE0_CLKREQ_M2/IUART
2_TX_M1/SPDIF_TX0_M0/Fl exBUS0_D15_M1/CAN1_TX _M2 |
GPIO4_B5_d (PU2.2K) |
3.3V |
|
89 |
I2C3_SDA_M0_Sensor |
PCIE0_WAKE_M2/IUART2_
RX_M1/SPDIF_RX0_M0/Fle xBUS0_CSN_M4/CAN1_RX _M2 |
GPIO4_B4_d (PU2.2K) |
3.3V |
|
90 |
SPK_CTL_H |
SPI3_CS1_M2/SPI4_CS0_M 2/PDM1_SDI0_M1/SAI1_SDI
0_M0/SAI4_SDO_M0 |
GPIO4_B3_d/ PWM2_CH7_M0 |
3.3V |
|
91 |
PCIE1_PERSTn |
SPI4_MISO_M2/PDM1_SDI1
_M1/SAI1_SDI1_M0/SAI1_S DO3_M0/FlexBUS1_D15_M1 |
GPIO4_B2_d/MIPI_TE_M0 |
3.3V |
|
92 |
IRC_BIN |
UART2_CTS_M1/UART6_C TS_M0/UART5_RX_M1/SPI4
_MOSI_M2/PDM1_SDI2_M1/ SAI1_SDI2_M0/SAI1_SDO2 _M0/FlexBUS1_D14_M1 |
GPIO4_B1_d |
3.3V |
|
93 |
IRC_AIN |
UART2_RTS_M1/UART6_R TS_M0/UART5_TX_M1/SPI4
_CLK_M2/PDM1_CLK1_M1/ SAI1_SDI3_M0/SAI1_SDO1 _M0/FlexBUS1_D13_M1 |
GPIO4_B1_d |
3.3V |
|
94 |
PCIE0_CLKREQn_M3 |
I2C6_SCL_M3/SPI4_MISO_ M0/SAI4_SDI_M2/VP1_SYN
C_OUT/CAN1_TX_M1 |
GPIO4_C6_d/ PWM2_CH2_M1/
SATA0_ACTLED_M1 |
3.3V |
|
95 |
PCIE0_PERSTn |
I2C6_SDA_M3/SPI4_CLK_M 0/SAI4_SCLK_M2/VP2_SYN
C_OUT/CAN1_RX_M1 |
GPIO4_C7_d/ PWM2_CH3_M1 |
3.3V |
|
96 |
PWM2_CH5_M1_FAN |
I2C3_SDA_M3/UART6_RX_ M3/SPI4_MOSI_M0/SAI4_S DO_M2/VP0_SYNC_OUT/IS
P_FLASH_TRIGOUT_M1 |
GPIO4_C5_d/ PWM2_CH5_M1/ SATA1_ACTLED_M1
PCIE0_WAKE_M3 |
3.3V |
| Bandika | Mawimbi | Maelezo au vitendaji | GPIO mfululizo | IO Voltage |
|
97 |
HDMI_TX_HPDIN_M0 |
I2C7_SDA_M3/UART11_RX
_M2/EDP_HPD_M0/PCIE1_ CLKREQ_M3/DSM_ALN_M1 |
GPIO4_C1_d/ PWM0_CH1_M1 |
3.3V |
|
98 |
HDMI_TX_SDA |
I2C2_SDA_M3/UART9_RX_
M2/CAN0_RX_M1/DSM_AR N_M1 |
GPIO4_C3_d/ PWM2_CH1_M1 |
3.3V |
|
99 |
HDMI_TX_SCL |
I2C2_SCL_M3/UART9_TX_ M2/CAN0_TX_M1/DSM_AR
P_M1 |
GPIO4_C2_d/ PWM2_CH0_M1 |
3.3V |
|
100 |
DP_HPDIN_M0 |
I2C3_SCL_M3/UART6_TX_ M3/SPI4_CSn0_M0/SAI4_LR CK_M2/ISP_PRLIGHT_TRIG
_M1 |
GPIO4_C4_d/ PWM2_CH6_M1 |
3.3V |
|
101 |
HDMI_TX_CEC_M0 |
I2C7_SCL_M3/UART11_TX_ M2/SPI4_CSn1_M0/SAI_MC
LK_M2/DSM_ALP_M1 |
GPIO4_C0_d/ PWM1_CH5_M1/
PCIE1_WAKE_M3 |
3.3V |
| 102 | GND | Ardhi | 0V | |
|
103 |
MIPI_DPHY_CSI0_PW REN_H_1V8 |
UART3_RTS_M0/SPI3_CSn 0_M0/SAI3_SDI_M2/ETH0_
RXD1_M1/CAN_RX_M3 |
GPIO3_A3_d/ VI_CIF_CLKI/
SPDIF_TX1_M1 |
1.8V |
|
104 |
SAI0_SDI0_M0_1V8 |
UART1_TX_M1/PDM0_SDI3
_M3/ETH0_TXD1_M1 |
GPIO2_B0_d/
VI_CIF_D13 |
1.8V |
|
105 |
SAI0_SDI1_M0_1V8 |
UART1_RX_M1/PDM0_SDI2
_M3/ETH0_TXD0_M1 |
GPIO2_B1_d/
VI_CIF_D12 |
1.8V |
|
106 |
SAI0_SDI2_M0_1V8 |
UART1_CTS_M1/SPI4_CSn 0_M3/PDM0_SDI1_M3/PCIE
0_CLKREQ_M0 |
GPIO2_B2_d/ VI_CIF_D11 |
1.8V |
|
107 |
SAI0_SDI3_M0_1V8 |
UART7_CTS_M1/SPI4_MOS I_M3/PDM0_SDI0_M3/SATA
0_ACTLED_M0 |
GPIO2_B4_d/ VI_CIF_D9 |
1.8V |
|
108 |
SAI0_SCLK_M0_1V8 |
I2C8_SCL_M2/UART8_CTS
_M1/UART7_RX_M0 |
GPIO2_B6_d |
1.8V |
|
109 |
SAI0_LRCK_M0_1V8 |
I2C8_SDA_M2/UART8_RTS
_M1/UART7_TX_M0 |
GPIO2_B7_d |
1.8V |
|
110 |
SAI0_MCLK_M0_1V8 |
UART7_RTS_M0/SPI4_MIS O_M3/PDM0_CLK0_M3/SAT
A1_ACTLED_M0 |
GPIO2_B5_d/ VI_CIF_D8 |
1.8V |
|
111 |
SAI0_SDO0_M0_1V8 |
I2C4_SCL_M2/UART8_TX_
M1/SPI4_CSn1_M3/ETH0_R XD0_M1 |
GPIO2_A6_d/ VI_CIF_D15 |
1.8V |
|
112 |
SAI0_SDO1_M0_1V8 |
I2C4_SDA_M2/UART8_RX_
M1/ETH0_TXCTL_M1 |
GPIO2_A7_d/
VI_CIF_D14 |
1.8V |
| Bandika | Mawimbi | Maelezo au vitendaji | GPIO mfululizo | IO Voltage |
|
113 |
SAI0_SDO2_M0_1V8 |
UART1_RTS_M1/SPI4_CLK
_M3/PDM0_CLK1_M3/PCIE 1_CLKREQ_M0 |
GPIO2_B3_d/ VI_CIF_D10 |
1.8V |
|
114 |
SPDIF_RX1_M1_1V8 |
UART3_RTS_M0/SPI3_MIS O_M0/SAI3_SDO_M2/ETH0
_RXCTL_M1/CAN_TX_M3 |
GPIO3_A2_d/
VI_CIF_CLKO/ MIPI_TE_M1 |
1.8V |
|
115 |
I2C7_SDA_M1_1V8 |
UART3_RX_M0/SPI3_MOSI
_M0/SAI3_LRCK_M2/ETH0_ MDC_M1(PU2.2K) |
GPIO3_A1_d/ VI_CIF_VSYNC |
1.8V |
|
116 |
I2C7_SCL_M1_1V8 |
UART3_TX_M0/SPI3_CLK_
M0/SAI3_SCLK_M2/ETH0_ MDIO_M1(PU2.2K) |
GPIO3_A0_d/ VI_CIF_HREF |
1.8V |
| 117 | GND | Ardhi | 0V | |
| 118 | DP_TX_AUXP | 0.5V | ||
| 119 | DP_TX_AUXN | 0.5V | ||
| 120 | USB2_OTG1_DP | 0.5V | ||
| 121 | USB2_OTG1_DM | 0.5V | ||
| 122 | USB2_OTG0_DP | 0.5V | ||
| 123 | USB2_OTG0_DM | 0.5V | ||
|
124 |
USB3_OTG0_SSRX1N
/DP_TX_D0N |
0.5V |
||
|
125 |
USB3_OTG0_SSRX1P
/DP_TX_D0P |
0.5V |
||
|
126 |
USB3_OTG0_SSTX1P/
DP_TX_D1P |
0.5V |
||
|
127 |
USB3_OTG0_SSTX1N/
DP_TX_D1N |
0.5V |
||
|
128 |
USB3_OTG0_SSRX2N
/DP_TX_D2N |
0.5V |
||
|
129 |
USB3_OTG0_SSRX2P
/DP_TX_D2P |
0.5V |
||
|
130 |
USB3_OTG0_SSTX2P/
DP_TX_D3P |
0.5V |
||
|
131 |
USB3_OTG0_SSTX2N/
DP_TX_D3N |
0.5V |
||
| 132 | GND | Ardhi | 0V | |
|
133 |
MIPI_DPHY_DSI_TX_
D0N |
MIPI_CPHY_DSI_TX_TRIO0
A |
0.5V |
|
|
134 |
MIPI_DPHY_DSI_TX_
D0P |
MIPI_CPHY_DSI_TX_TRIO0
B |
0.5V |
|
|
135 |
MIPI_DPHY_DSI_TX_
D1N |
MIPI_CPHY_DSI_TX_TRIO0
C |
0.5V |
| Bandika | Mawimbi | Maelezo au vitendaji | GPIO mfululizo | IO Voltage |
|
136 |
MIPI_DPHY_DSI_TX_
D1P |
MIPI_CPHY_DSI_TX_TRIO1
A |
0.5V |
|
|
137 |
MIPI_DPHY_DSI_TX_
CLKN |
MIPI_CPHY_DSI_TX_TRIO1
B |
0.5V |
|
|
138 |
MIPI_DPHY_DSI_TX_
CLBP |
MIPI_CPHY_DSI_TX_TRIO1
C |
0.5V |
|
|
139 |
MIPI_DPHY_DSI_TX_
D2N |
MIPI_CPHY_DSI_TX_TRIO2
A |
0.5V |
|
|
140 |
MIPI_DPHY_DSI_TX_
D2P |
MIPI_CPHY_DSI_TX_TRIO2
B |
0.5V |
|
|
141 |
MIPI_DPHY_DSI_TX_
D3N |
MIPI_CPHY_DSI_TX_TRIO2
C |
0.5V |
|
|
142 |
MIPI_DPHY_DSI_TX_
D3P |
0.5V |
||
|
143 |
MIPI_DPHY_CSI0_RX
_D0P |
MIPI_CPHY_CSI_TX_TRIO0
B |
0.5V |
|
|
144 |
MIPI_DPHY_CSI0_RX
_D0N |
MIPI_CPHY_CSI_TX_TRIO0
A |
0.5V |
|
|
145 |
MIPI_DPHY_CSI0_RX
_D1P |
MIPI_CPHY_CSI_TX_TRIO1
A |
0.5V |
|
|
146 |
MIPI_DPHY_CSI0_RX
_D1N |
MIPI_CPHY_CSI_TX_TRIO0
C |
0.5V |
|
|
147 |
MIPI_DPHY_CSI0_RX
_CLKP |
MIPI_CPHY_CSI_TX_TRIO1
C |
0.5V |
|
|
148 |
MIPI_DPHY_CSI0_RX
_CLKN |
MIPI_CPHY_CSI_TX_TRIO1
B |
0.5V |
|
|
149 |
MIPI_DPHY_CSI0_RX
_D2P |
MIPI_CPHY_CSI_TX_TRIO2
B |
0.5V |
|
|
150 |
MIPI_DPHY_CSI0_RX
_D2N |
MIPI_CPHY_CSI_TX_TRIO2
A |
0.5V |
|
|
151 |
MIPI_DPHY_CSI0_RX
_D3P |
0.5V |
||
|
152 |
MIPI_DPHY_CSI0_RX
_D3N |
MIPI_CPHY_CSI_TX_TRIO2
C |
0.5V |
|
| 153 | GND | Ardhi | 0V | |
| 154 | HDMI_TX_D3N | EDP_TX3N | 0.5V | |
| 155 | HDMI_TX_D3P | EDP_TX3P | 0.5V | |
| 156 | HDMI_TX_D0P | EDP_TX0P | 0.5V | |
| 157 | HDMI_TX_D0N | EDP_TX0N | 0.5V | |
| 158 | HDMI_TX_D1P | EDP_TX1P | 0.5V | |
| 159 | HDMI_TX_D1N | EDP_TX1N | 0.5V | |
| 160 | HDMI_TX_D2P | EDP_TX2P | 0.5V |
| Bandika | Mawimbi | Maelezo au vitendaji | GPIO mfululizo | IO Voltage |
| 161 | HDMI_TX_D2N | EDP_TX2N | 0.5V | |
| 162 | HDMI_TX_SBDN | EDP_AUXN | 0.5V | |
| 163 | HDMI_TX_SBDP | EDP_AUXP | 0.5V | |
| 164 | GND | Ardhi | 0V | |
|
165 |
MIPI_DPHY_CSI2_RX
_CLKP |
0.5V |
||
|
166 |
MIPI_DPHY_CSI2_RX
_CLKN |
0.5V |
||
|
167 |
MIPI_DPHY_CSI1_RX
_CLKN |
0.5V |
||
|
168 |
MIPI_DPHY_CSI1_RX
_CLKP |
0.5V |
||
|
169 |
MIPI_DPHY_CSI1_RX
_D3N |
MIPI_DPHY_CSI2_RX_D1N |
0.5V |
|
|
170 |
MIPI_DPHY_CSI1_RX
_D3P |
MIPI_DPHY_CSI2_RX_D1P |
0.5V |
|
|
171 |
MIPI_DPHY_CSI1_RX
_D2N |
MIPI_DPHY_CSI2_RX_D0N |
0.5V |
|
|
172 |
MIPI_DPHY_CSI1_RX
_D2P |
MIPI_DPHY_CSI2_RX_D0P |
0.5V |
|
|
173 |
MIPI_DPHY_CSI1_RX
_D1N |
0.5V |
||
|
174 |
MIPI_DPHY_CSI1_RX
_D1P |
0.5V |
||
|
175 |
MIPI_DPHY_CSI1_RX
_D0N |
0.5V |
||
|
176 |
MIPI_DPHY_CSI1_RX
_D0P |
0.5V |
||
| 177 | VCC_1V8_S3 | 1.8V GPIO Pato la Nguvu | Upeo wa 500mA | 1.8V |
|
178 |
USB2_OTG1_VBUSDE
T |
Uingizaji wa USB2 VBUS |
3.3V |
|
|
179 |
TP_INT_L |
I3C0_SDA_PU_M0/UART10
_RX_M2/SAI0_SDO0_M1/D P_HPD_M1 |
GPIO0_C5_d |
3.3V |
|
180 |
LCD_BL_PWM1_CH1_
M0 |
I2C1_SDA_M1/UART4_RX_
M2/REFCLK2_OUT |
GPIO0_B5_d/
PWM1_CH1_M0 |
3.3V |
|
181 |
PCIE1_WAKEn_M0 |
I2C4_SDA_M0/UART1_RTS
_M0/PDM0_SDI3_M0/SAI0_ SDO1/SDI3_M1 |
GPIO0_D3_d/ PWM2_CH0_M0 |
3.3V |
|
182 |
GPIO0_B4_d |
I2C1_SCL_M1/UART4_TX_
M2/REFCLK1_OUT |
PWM1_CH0_M0 |
3.3V |
| Bandika | Mawimbi | Maelezo au vitendaji | GPIO mfululizo | IO Voltage |
|
183 |
USBCC_INT_L |
SPI0_MISO_M0/PDM0_SDI1
_M0/SAI0_SDO3/SDI1_M1 |
GPIO0_D1_d |
3.3V |
|
184 |
PCIE0_PWREN_H |
I2C3_SDA_M1/SPI0_CLK_M
0/SAI0_LRCK_M1 |
GPIO0_C7_d |
3.3V |
|
185 |
PCIE0_WAKEn_M0 |
I2C4_SCL_M0/UART1_CTS
_M0/PDM0_SDI2_M0/SAI0_ SDO2/SDI2_M1 |
GPIO0_D2_d/ PWM1_CH5_M0 |
3.3V |
|
186 |
LCD_PWREN_H |
I2C3_SCL_M1/SPI0_CSn0_
M0/SAI0_SCLK_M1 |
GPIO0_C6_d |
3.3V |
|
187 |
I2C2_SCL_M0_CC_RT
C |
UART1_TX_M0/PWM1_CH4
_M0(PU2.2K) |
GPIO0_B7_d |
3.3V |
|
188 |
I2C2_SDA_M0_CC_RT
C |
UART1_RX_M0/PWM1_CH3
_M0(PU2.2K) |
GPIO0_C0_d |
3.3V |
|
189 |
GPIO0_C4_d |
UART10_TX_M2/PDM0_CL
K0_M0/SAI0_MCLK_M1 |
PWM0_CH0_M0 |
3.3V |
|
190 |
I2C0_SCL_M1_TP |
I3C0_SCL_M0/UART8_TX_
M2(PU2.2K) |
GPIO0_C1_d |
3.3V |
|
191 |
I2C0_SDA_M1_TP |
I3C0_SDA_M0/UART8_RX_
M2(PU2.2K) |
GPIO0_C2_d |
3.3V |
|
192 |
TP_RST_L |
SPI0_MOSI_M0/PDM0_SDI0
_M0/SAI0_SDI0_M1 |
GPIO0_D0_d |
3.3V |
| 193 | GND | Ardhi | 0V | |
| 194 | PCIE0_RXP | SATA0_RXP | 0.5V | |
| 195 | PCIE0_RXN | SATA0_RXN | 0.5V | |
| 196 | PCIE0_TXN | SATA0_TXN | 0.5V | |
| 197 | PCIE0_TXP | SATA0_TXP | 0.5V | |
| 198 | PCIE0_REFCLKP | 0.5V | ||
| 199 | PCIE0_REFCLKN | 0.5V | ||
|
200 |
PCIE1_TXP |
SATA1_TXP/USB3_OTG1_S
STXP |
0.5V |
|
|
201 |
PCIE1_TXN |
SATA1_TXN/USB3_OTG1_S
STXN |
0.5V |
|
|
202 |
PCIE1_RXP |
SATA1_RXP/USB3_OTG1_S
SRXP |
0.5V |
|
|
203 |
PCIE1_RXN |
SATA1_RXN/USB3_OTG1_S
SRXN |
0.5V |
|
| 204 | PCIE1_REFCLKP | 0.5V | ||
| 205 | PCIE1_REFCLKN | 0.5V | ||
| 206 | GND | Ardhi | 0V | |
|
207 |
MIPI_DPHY_CSI4_RX
_CLKP |
0.5V |
| Bandika | Mawimbi | Maelezo au vitendaji | GPIO mfululizo | IO Voltage |
|
208 |
MIPI_DPHY_CSI4_RX
_CLKN |
0.5V |
||
|
209 |
MIPI_DPHY_CSI3_RX
_D3N |
MIPI_DPHY_CSI4_RX_D1N |
0.5V |
|
|
210 |
MIPI_DPHY_CSI3_RX
_D3P |
MIPI_DPHY_CSI4_RX_D1P |
0.5V |
|
|
211 |
MIPI_DPHY_CSI3_RX
_D2N |
MIPI_DPHY_CSI4_RX_D0N |
0.5V |
|
|
212 |
MIPI_DPHY_CSI3_RX
_D2P |
MIPI_DPHY_CSI4_RX_D0P |
0.5V |
|
|
213 |
MIPI_DPHY_CSI3_RX
_CLKN |
0.5V |
||
|
214 |
MIPI_DPHY_CSI3_RX
_CLKP |
0.5V |
||
|
215 |
MIPI_DPHY_CSI3_RX
_D1N |
0.5V |
||
|
216 |
MIPI_DPHY_CSI3_RX
_D1P |
0.5V |
||
|
217 |
MIPI_DPHY_CSI3_RX
_D0N |
0.5V |
||
|
218 |
MIPI_DPHY_CSI3_RX
_D0P |
0.5V |
||
Seti ya Maendeleo (EM3576)
Mwongozo wa Kubuni Vifaa
Rejea ya Mzunguko wa Pembeni
Nguvu ya Nje
Debug Circuit
Mzunguko wa HDMI TX
Upungufu wa urefu wa Bodi ya Mama
| Kiolesura cha urefu wa MIPI CSI0 4-Lane | |||
| MIPI_CSI0_RX0_CLKP | MIPI_CSI0_RX0_D0P | (53.5) | (+40) |
| MIPI_CSI0_RX0_D1P | (35.046) | (+30) | |
| MIPI_CSI0_RX0_D2P | |||
| MIPI_CSI0_RX0_D3P | (-25.758) | (-30) | |
Kizuizi cha manjano ni tofauti ya urefu wa kikundi CM3576 CSI0.
PCB Footprint
Tabia za Umeme wa Bidhaa
Uharibifu na joto
| Alama | Kigezo | Dak | Chapa | Max | Kitengo |
|
VCC_SYS |
Mfumo Voltage |
3.4V |
4 |
5.5 |
V |
|
Isys_in |
VCC_SYS
pembejeo Sasa |
1750 |
mA |
||
|
VCC_RTC |
RTC Voltage |
1.8 |
3 |
3.4 |
V |
|
Iirtc |
Ingizo la RTC
Ya sasa |
5 |
8 |
uA |
|
|
I3v3_nje |
VCC_3V3
pato Sasa |
500 |
mA |
||
|
I1v8_nje |
VCC_1V8
pato Sasa |
500 |
mA |
||
|
Ta |
Joto la Uendeshaji |
0 |
70 |
°C |
|
|
Tstg |
Joto la Uhifadhi |
-40 |
85 |
°C |
Kuegemea kwa Mtihani
| Mtihani wa Uendeshaji wa Joto la Juu | ||
| Yaliyomo | Uendeshaji 8h kwa joto la juu | 55°C±2°C |
| Matokeo | TBD | |
| Mtihani wa Maisha ya Uendeshaji | ||
| Yaliyomo | Kufanya kazi katika chumba | 120h |
| Matokeo | TBD | |
Nyaraka / Rasilimali
 |
Mfumo wa Boardcon CM3576 kwenye Moduli [pdf] Mwongozo wa Mtumiaji Mfumo wa CM3576 kwenye Moduli, CM3576, Mfumo kwenye Moduli, Moduli |
