SURNICE RHT190 Socket Remote Control User Guide

To operate the device using the remote control:
– Press AON to turn on the device.
– Press AOFF to turn off the device.
– Press ALLON to turn on all devices.
– Press ALLOFF to turn off all devices.

Clear Receiver Memory

Press and hold the button for around 20 seconds until the
indicator light turns off.

Frequently Asked Questions (FAQ)

Problem: The indicator light of the transmitter does not
flash.

Possible Cause: The battery is not sufficient
or the installation of batteries is not correct.
Solution: Replace with a new battery or remove
and reinstall the battery to ensure proper contact.

Problem: The receiver does not work.

Possible Cause: One switch button controls
multiple outlets or the pairing failed.
Solution: Re-pair the receiver and
transmitter, clear all pairs of the socket, or adjust the distance
between remote control and receiver.

Problem: Safety Precautions.

Solution: Ensure button batteries are kept
away from children, and seek medical advice immediately if a
battery is swallowed or inserted into the body.

“`

View Fullscreen

PRODUCT STRUCTURE
Socket

LED ON/OFF
Pair Reset

Remote controller

Indicator light

Off

All On

All Off

BATTERY INSTALLATION

Open the battery cover

Remove the battery cover

R2 03 2

Install the battery and cover

Lock the battery cover

Positive pole

CR2032

Battery Compartment

Negative pole

Install the battery correctly

Remove the battery correctly

A
Install the battery incorrectly

A 1:2
Short circuit

PAIRING SETTING

1. Plug the socket into a power source

2.Press and hold the button till the indicator light starts to flash slowly.

Indicator light

ex1+1

ex1+2

ex1+3 ex1+4

ex1+5

E
3. Press AON button of the remote controller after pairing done, LED indicator light is ON (For BON.CON.DON.EON pairing in sequence, please refer to the AON pairing steps)

INSTRUCTIONS

1. Remote control operation method
Example: Press the AON key to turn on the device, press the AOFF key to turn off the device. Example: Press the ALLON key to turn on all devices, press the ALLOFF key to turn off all devices.
Indicator light

Off

All On

All Off

2.If the remote controller is not available, the socket could be ON/OFF by pressing the button in the socket.

Off

CLEAR RECEIVER MEMORY
Press and hold the button around 20 seconds and release it after the indicator light turns off.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ·Reorient or relocate the receiving antenna. ·Increase the separation between the equipment and receiver. ·Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ·Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Information The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition, compliance with exposure requirements.
5

PRODUCT SPECIFICATION
Model: SN10015USA Working voltage: 120V~ 60Hz 10A Max power rating: 1200W Operating range: Max 130 ft(outdoor open area) Frequency: 433.92MHz LED flash: Red Working temperature: 0~35 Use scene: Indoor Standby power consumption:0.3W
Model: 50190 Frequency: 433.92MHz Working temperature: 0~35 Working voltage: 1x3V CR2032 Standby current:5A Transmit power:5dBm
6

FAULT ANALYSIS AND SOLUTION

Problem

Possible Cause

Solution

The indicator light
of the transmitter does not flash

The battery is not sufficient The installation of batteries is not correct

Replace with a new battery
Remove the battery and reinstall it again to make sure the contact is good

The receiver does not work
One switch button controls multiple
outlets

The pairing failed.
The transmitter is too far from the receiver or there is a metal obstacle near the receiver’s mounting location
Multiple outlets are paired with the switch button

Re-pair the receiver and transmitter again
Reduce the distance between the remote control and the receiver or move the metal barrier between them
Clear all pairs of the socket and then re-pair to the corresponding switch buttons

PRECAUTIONS
1. Use Information
The following equipment must not be connected to the remote control plug: · Equipment exceeding the technical value of the remote control plug (-> technical data). · Equipment with motor capacitors (such as refrigerators, etc.). · Opening the device unattended can cause fire or other damage (such as irons,etc.). · Cathode-ray tube television. · Do not use remote control plug outdoors, near dripping water, and in damp rooms
(bathrooms, etc.). · In an emergency, you must have quick access to the remote control plugs so that they can
be removed from the grounded contact plugs in the event of a hazard.
2. Safety Information
· Do not plug multiple devices into each other. · There is no voltage when the plug is disconnected. · Only suitable for dry rooms. · The remote control plug can only be connected to a properly installed grounded contact
socket (120V_60Hz). · The remote control plug must not be plugged into an extension cord and must not be
overloaded (maximum 1200W). · Do not open the device. Improper assembly may cause electric shock, short circuit or fire. · The range of the remote control plug is severely affected by structural conditions (such as
reinforced concrete) or sources of electrical / electromagnetic interference (fluorescent lights, cordless phones or earphones, TV/monitors, cables, etc.). If necessary, remove disturbance sources or keep a proper distance. · Keep the equipment installation at a distance of more than 80CM from the ground. · Avoid humidity, extreme temperature, vibration and shock. · Clean with a soft, slightly damp cloth. Do not use detergents or solvents. Do not immerse in water. · Do not plug pins or other metal objects into power outlets.
8

PRECAUTIONS
· Do not expose the battery to extreme temperatures such as direct sunlight or fire. Do not place the device on the heater. Leaking battery acid can cause damage.
· Always install batteries with the correct polarity (+ and ), as shown in the battery compartment. · Notice! If the battery is incorrectly installed, there is a danger of explosion. · When replacing the battery, only use the same type of battery. · If the battery leaks, remove it from the battery compartment with a clothdispose the battery
properly. If battery acid leaks, avoid contact with skin, eyes, and mucous membranes. If you come into contact with acid, immediately rinse the affected skin thoroughly with water and consult a doctor. · Store the battery in a well-ventilated and dry place. · If you do not use the device for a long time, remove the battery. · Risk of explosion! Do not use other reagents to charge or reactivate the battery, and do not disassemble, throw into fire or short-circuit the battery. · Remove the used battery from the device and dispose it immediately.
Warning : 1. This product contains button batteries. If you swallow a button battery, it will cause severe internal
hurt within 2 hours and may result in death. 2. Keep new and used batteries away from children. 3. If the battery compartment cannot be closed tightly, please stop using the product and keep it away
from children. 4. If you think the battery may be swallowed or entered any part of the body, please seek medical
advice immediately.
9

Wireless Remote Plug User Guide Model:SN10015USA+50190

Documents / Resources

SURNICE RHT190 Socket Remote Control [pdf] User Guide
RHT190, SN10015USA, 50190, RHT190 Socket Remote Control, RHT190, Socket Remote Control, Remote Control

References

User Manual

SURNICE RHT190 Socket Remote Control User Guide

RHT190 Socket Remote Control

Product Specifications

Product Usage Instructions

Battery Installation

Pairing Setting

Remote Control Operation