SR-MT9041A-D Zig Bee Dual Tech Mini Smart Dimmer
“
Product Specifications
- Input Voltage: 100-240VAC
- Output Voltage: 100-240VAC
- Output Current: 0.1-1.1A
- Size (LxWxH): 42x38x16mm
Product Usage Instructions
Safety & Warnings
1. Ensure proper wiring according to the connection diagram.
2. This Matter thread device is a wireless receiver that
communicates with various Matter compatible systems.
Operation
- Connect the Matter thread dimmer to the wiring diagram and
power it on. - Add the Matter thread dimmer to the Apple Home app by scanning
the QR code sticker on the dimmer. - Press the reset button 5 times before scanning the QR code
sticker to reset the dimmer for discovery by the Apple Home
app. - When adding the dimmer to a room, ensure it is in the same room
as the HomePod mini. - Once added to the gateway successfully, control the on/off and
brightness of the dimmer through the app.
To set minimum brightness:
- Press and hold down the button for 3 seconds when current
brightness value is between 1%-50%. - If current brightness value is 100%, previously set minimum
brightness will be deleted. - Once set, the connected load cannot be dimmed below this
level.
Frequently Asked Questions (FAQ)
How do I reset the dimmer?
To factory reset the dimmer, turn on/off the load.
What are the compatible load types and maximum loads?
Dimmable LED Lamps: 200W @ 230V, 100W @
110V
Dimmable LED Drivers: 200W @ 230V, 100W @
110V
Incandescent Lighting, HV Halogen Lamps: 250W @
230V, 125W @ 110V
Low Voltage Halogen Lighting with Electronic
Transformers: 200W @ 230V, 100W @ 110V
“`
Matter Over Thread + Zigbee Dual Tech Mini Smart Dimmer
Function Introduction · ImportantRead All Instructions Prior to Installation.
42 mm
“Reset” Key: factory reset of the dimmer, turn on/off load
Min. Set Button 1) Set minimum brightness 2) Set startup brightness
Reset Min.Set
Matter Phase Dimmer
100-240V~50/60Hz Max.250W Resistive Max.200W LED
38 mm
N N O L L L SW
Accessory 1: Wire clamp cover. Need to purchase separately.
16 mm
Accessory 2: din rail bracket. Need to purchase separately.
Product Data
Input Voltage 100-240VAC
Output Voltage 100-240VAC
Output Current 0.1-1.1A
Size (LxWxH) 42x38x16mm
Load Symbol
Load Type
Compatible Load Types Maximum Load
Remarks
Dimmable LED lamps
200W @ 230V 100W @ 110V
Due to variety of LED lamp designs, maximum number of LED lamps is further dependent on power factor result when connected to dimmer.
Dimmable LED drivers
200W @ 230V 100W @ 110V
Maximum permitted number of drivers is 200W divided by driver nameplate power rating.
Incandescent lighting, HV Halogen lamps
250W @ 230V 125W @ 110V
Low voltage halogen lighting with electronic transformers
200W @ 230V 100W @ 110V
1
Features
· Matter over thread + Zigbee dual tech AC phase cut dimmer · 100-240VAC wide input and output voltage · Supports resistive loads, capacitive loads or inductive loads · 1 channel output, up to 250W · Input and output with screw terminals, safe and reliable · Trailing edge dimming · App control + touchlink remote control + green power kinetic switch control · App control through Matter (e.g. Apple Home, Amazon Alexa, Google Home) · Fully compatible with universal Matter ecosystems from different manufacturers · Can be voice controlled through Apple Siri, Google Assistant, Amazon Alexa · Mini Size, easy to be installed into a standard wall box · Waterproof grade: IP20
Main Features: · Can operate under two-wire connection with no neutral lead or three-wire connection with neutral lead · Advanced microprocessor control · Implemented algorithm of smart light source detection · Active power and energy metering functionality · Soft start function · Innovative minimum dimming level and startup brightness setting function · Works with various types of switches momentary, toggle, etc. · Active element: semiconductor electronic switch · To be installed in wall switch boxes of dimensions allowing for installation, conforming to provisions of
applicable regulations · The Bypass is an extension unit
As a dimmer it operates under the following loads: · Conventional incandescent and HV halogen light sources · ELV halogen lamps and dimmable LED bulbs (with electronic transformers) · MLV halogen lamps (with ferromagnetic transformers) · Dimmable LED bulbs
Safety & Warnings
· DO NOT install with power applied to the device. · DO NOT expose the device to moisture.
Operation
1 Do wiring according to connection diagram correctly. (See P9-10) 2 This Matter thread device is a wireless receiver that communicates with a variety of Matter
compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible Matter system.
2
3 Add to a Matter gateway and control through the gateway:
5
6
7
Note Step 1:
An Apple HomePod mini is used as a Matter border router for adding and controlling the device. For other Matter border routers, please refer to their user manuals to learn how to add and control Matter devices.
Prepare an iPhone (iOS 16.2 or later) or iPad (iPadOS 16.2 or later) with the latest version rmware, and prepare an Apple HomePod mini with the latest version rmware.
Step 2:
Connect the iPhone or iPad to your home WLAN network. Run the Apple Home app and set up the HomePod mini as instructed by Apple (as shown in Figure 1 to Figure 7).
1
2
3
4
Step 3:
Do wiring of the Matter thread dimmer according to the wiring diagram (See P9-10) and power on it.
Step 4:
Add the Matter thread dimmer to the Apple Home app by scanning the QR code sticker on the dimmer as shown in Figure 8 to Figure 15.
8
9
3
4
NoteBefore scanning the QR coder sticker on the dimmer as shown in Figure 10, short press the reset button 5 times to reset the dimmer so that it can be discovered by the Apple Home app. Otherwise if it has already been added to another gateway, current gateway can not discover and add it.
Press 5X
Reset
10
11
12
13
14
15
Note When choose the room that you would like to add the dimmer to, please make sure to choose the same room that the HomePod mini is located as shown in Figure 13.
Step 5:
Once the dimmer is added to the gateway successfully, tap on the device to control on/o and brightness of the dimmer as shown in Figure 16 to Figure 18.
16
17
18
5
6
4 Minimum and Startup Brightness Setting Button
Minimum brightness: Press and hold for 3S
Startup brightness: Press 2X
Min.Set
Min.Set
Press and hold down the button for 3 seconds to set minimum brightness: when current brightness value is 1%-50%, it will be set as minimum brightness. When current brightness value is 100%, previously set minimum brightness will be deleted. Once a minimum brightness is set, the connected load can not be dimmed below this level.
Short press the button twice to set startup brightness: when current brightness value is 1%-50%, it will be set as startup brightness. When current brightness value is 0%, previously set startup brightness will be deleted.
Note
startup brightness setting function is to avoid the phenomenon that some dimmable LED drivers can not be turned on after dimmed to a low level and turned o . Once setting a startup brightness, if the startup brightness is higher than dimmed level before turned o , the driver will rst go to the startup brightness after turned on then drop down to the dimmed level. If the startup brightness is lower than the dimmed level before tured o , the driver will directly go to the dimmed level after turned on.
5 Touchlink to a Zigbee remote
Step 1: Short press “Reset” button 4 times to start Touchlink pairing. Step 2: Bring the remote within 10cm of the receiver. Step 3: Set the remote into Touchlink pairing, please refer to its manual. Step 4: There shall be indication on the remote for successful link and the connected light will flash.
Note: There are two control situations: 1. Only one remote, to control one or more receivers: directly perform Touchlink pairing between the remote and the receiver.
2. Only one receiver, to be controlled by multiple remotes, or multiple remotes and multiple receivers with cross-control: use one receiver as the Zigbee hub, add all remotes and other receivers to the hub, and then perform Touchlink pairing between the remotes and the receivers. The steps are as follows: Step 1: Use one receiver as the Zigbee hub and short press “Reset” button 4 times to start adding Zigbee devices. Step 2: Reset power of another receiver once to enter Zigbee network pairing mode, it will be added by the hub, and the connected light will flash. Step 3: Set a Zigbee remote to enter Zigbee network pairing mode, it will be added by the hub, and the indicator will flash to indicate. Step 4: Add more receivers and remotes to the hub as you would like, refer to the corresponding remote manual. Step 5: Touchlink the added receivers and the remotes.
7
6 Learning to a Zigbee Green Power Switch Step 1: Short press “Reset” button 4 times to start Learning mode. Step 2: Set the green power switch into Learning mode, please refer to its manual. Step 3: There shall be indication on the switch for successful learning.
Note: There are two control situations: 1. Only one receiver, to be controlled by multiple GP switches: directly perform pairing between the GP switch and the receiver.
2. Only one GP switch, to control multiple receivers, or multiple GP switches and multiple receivers with cross-control: use one receiver as the Zigbee hub, add all other receivers to the hub, and then pair the GP switch with the receiver. The steps are as follows: Step 1: Use one receiver as the Zigbee hub and short press “Reset” button 4 times to start adding Zigbee devices. Step 2: Reset power of another receiver once to enter Zigbee network pairing mode, it will be added by the hub and the connected light will flash. Step 3: Add more receivers to the hub as you would like. Step 4: Pair the added receivers with the GP switches.
7 Controlled by a push switch
Once connected with a push switch, click the push switch to switch ON/OFF, press and hold down it to increase/ decrease light intensity.
8 Restore factory settings
To restore the factory settings, short press the “Reset” button 5 times or switch the device on and off in the following sequence.
Stage 1 2 3 4 5 6 7 8 9 10
Duration < 1s > 3s
5s – 15s > 3s < 1s > 3s < 1s > 3s < 1s > 3s
State ON OFF ON OFF ON OFF ON OFF ON OFF
8
Wiring Diagram
* Notes for the diagrams: L – terminal for live lead N – terminal for neutral lead O – output terminal of the dimmer (controlling connected light source) SW – terminal for switch
* Supported Switch Types: The switch types this device supports can be con gured by factory setting: 1. Push Switch (factory default setting) 2. Toggle On/O Switch (can be con gured by factory setting upon request)
Method 1: With neutral
Reset Min.Set
Matter Phase Dimmer
100-240V~50/60Hz Max.250W Resistive Max.200W LED
N N O L L L SW
N L
Method 2: Without neutral
Reset Min.Set
Matter Phase Dimmer
100-240V~50/60Hz Max.250W Resistive Max.200W LED
N N O L L L SW
Reset Min.Set
Matter Phase Dimmer
100-240V~50/60Hz Max.250W Resistive Max.200W LED
N N O L L L SW
Bypass
N
N
L
L
* When using the device without neutral, the smart dimmer requires at least 20W @ 240 VAC of power consumption to operate. If the connected light has a smaller power consumption, then Bypass is needed for the device to work.
9
10
Documents / Resources
 |
Sunricher SR-MT9041A-D Zig Bee Dual Tech Mini Smart Dimmer [pdf] Owner's Manual SR-MT9041A-D Zig Bee Dual Tech Mini Smart Dimmer, SR-MT9041A-D, Zig Bee Dual Tech Mini Smart Dimmer, Mini Smart Dimmer, Smart Dimmer |