SUNRICHER-logo

SUNRICHER SR-2100AMP-RDM-8CH-3 8 Way RDM Enabled DMX Splitter

SUNRICHER-SR-2100AMP-RDM-8CH-3-8-Way-RDM-Enabled-DMX Splitter-product-image

8-Way RDM Enabled DMX Splitter

Important: Read All Instructions Prior to Installation

Function introduction

SUNRICHER-SR-2100AMP-RDM-8CH-3-8-Way-RDM-Enabled-DMX Splitter-1

Product Data

No. Input Voltage Input Current Input Signal DMX/RDM

Connection Ports

Connector Pin Out Size(LxWxH) Operation Temperature
 

1

 

12-24VDC

 

Max. 300mA

 

DMX/RDM

Input: (1x) Male 3-Pin XLR Output: (8x) Female 3-Pin XLR Pin1: Ground Pin2: Data- Pin3: Data+  

199x125x44mm

 

-20℃ ~ +50℃

 

2

 

12-24VDC

 

Max. 300mA

 

DMX/RDM

 

Input: (1x) Male 5-Pin XLR Output: (8x) Female 5-Pin XLR

Pin1: Ground Pin2: Data- Pin3: Data+ Pin4: NC Pin5: NC  

199x125x44mm

 

-20℃ ~ +50℃

  • 8-Way RDM enabled DMX splitter
  • DMX/RDM compatible
  • RDM enabled – ANSI E1.20 compliant
  • Extend both cable distance (up to 300m) and the number of devices (up to 32 devices per output, total 256 devices)
  • Plug and play, 3/5-Pin XLR male DMX input, eight XLR female DMX outputs
  • 8 outputs are full isolated from the input, the outputs are not isolated from each other
  • Each output provides LED data indicators, providing full confirmation of proper operation
  • Supports bi-directional communications for discovery, addressing and DMX control of RDM enabled devices
  • A feed through XLR female connector is provided at the input, allowing this unit to be placed in the middle of an existing DMX chain

Safety & Warnings

  • DO NOT install with power applied to device.
  • DO NOT expose the device to moisture.

Wiring Diagram

SUNRICHER-SR-2100AMP-RDM-8CH-3-8-Way-RDM-Enabled-DMX Splitter-2

Note:

  1. This splitter is placed in the middle of an existing DMX chain.
  2. Max. allowed data cable length in a DMX chain is 300m, each output is branch DMX chain.
  3. Max. allowed data cable length connected to each output (branch DMX chain) is 300m.
  4. Max. 32 devices can be connected to each output of the splitter in daisy-chain.
  5. Total 32*8=256 devices can be connected to 8 outputs of the splitter.
  6. Please attach a 120ohm, 0.5W resistor between Data+ and Data- wires on the last device of each DMX chain.

Product Dimension

SUNRICHER-SR-2100AMP-RDM-8CH-3-8-Way-RDM-Enabled-DMX Splitter-3

Documents / Resources

SUNRICHER SR-2100AMP-RDM-8CH-3 8 Way RDM Enabled DMX Splitter [pdf] Instruction Manual
SR-2100AMP-RDM-8CH-3, 8 Way RDM Enabled DMX Splitter, SR-2100AMP-RDM-8CH-3 8 Way RDM Enabled DMX Splitter, RDM Enabled DMX Splitter, DMX Splitter, Splitter

References

Leave a comment

Your email address will not be published. Required fields are marked *