T6F0A, T6F0B Smart POS System
“
Product Specifications:
- Model: T6F0A/T6F0B
- Supported Cards: PSAM, Micro SD, Nano SIM
- Scanning Capability: 1D/2D
- Connectivity: NFC, IC, Type-C, OTG, Pogo Pin
- Dimensions: 80mm x 160mm
- Display: Used for multimedia functions and information
display
Product Usage Instructions:
1. Power On/Off:
Short press the Power button to turn on the screen or lock it.
Long press for 2-3 seconds to boot up the device when it’s off.
Press for 2-3 seconds to power off or restart the device when it’s
on. In case of a crash, press for 11 seconds to power off the
device.
2. Battery Handling:
Open the back cover lock to access the battery. Follow the arrow
direction to install or remove the battery. Ensure the battery
cover is properly installed for normal use.
3. Card Slots:
You can insert PSAM card, Micro SD card, and Nano SIM card into
their respective slots on the device.
4. Camera and Scanner:
The device supports front/rear camera for photo taking and quick
code scanning. The scanner supports both photo taking and quick
1D/2D code scanning.
5. NFC and IC Card Reader:
NFC functionality allows tapping and reading NFC cards. The IC
Card Reader supports reading chip cards with dual-sided
insertion.
Use the indicator lights for charging, scanning, and information
display. Set shortcut functions using the function keys. Short
press the Scan Button to enable scanning.
7. Connectivity and Charging:
Use Type-C port for charging devices and developer debugging.
The expansion interface allows connecting related accessories.
8. Safety Warnings:
If you notice any unusual odors, overheating, or smoke, stop
using the device immediately.
Frequently Asked Questions (FAQ):
Q: How do I charge the device?
A: Use the provided charging cable to connect to a power source
via the Type-C port on the device.
Q: Can I use a different SIM card size?
A: The device supports Nano SIM cards only. Do not attempt to
insert other sizes as it may damage the slot.
“`
80mm
Scan to know more
Laser light exit port
1
2
1
2
English English English English English English
160mm
388505 www.sunmi.com 400-6666-509
M050
Model:T6F0A/T6F0B
:
PSAM Micro SD Nano SIM
PSAMMicro SDNano SIM
2-3
2-3 11
/
1D/2D
NFC
IC
Type-C
OTG
Pogo Pin
·
· B
· · · · ·
· ·
· · · · · -20~55 · 5000m ·
· · ()
() · ROM
Pb (Hg) (Cd) (Cr(VI))
(PBB)
(PBDE)
SJ/T11363-2006
X SJ/T11363-2006″×”
· · · · · ·
· ·
APK
()”” 3C NFC 1.5A/m 7.5A/m”–NFC” ;
() ();
()() ;
()(ISM) ();
() () ;
() () () ;
()5000 ;
()NFC
Display
Used for multimedia functions and information display, etc.
Back Cover Lock
Slide left and right to switch the battery cover function. Note: The battery cover should be installed on the device, otherwise it will affect normal use.
Battery
Open the battery cover, install or remove the battery in the direction indicated by the arrow.
PSAM card slot, Micro SD card slot, Nano SIM card slot
You can insert a PSAM card slot, Micro SD card slot and Nano SIM card slot
Power button/Fingerprint recognition (optional)
Short Press: turn on the screen or lock the screen; Long Press: press for 2-3 seconds to boot up the device when it is off. Press for 2-3 seconds to power off or restart the device when it is on. Press for 11 seconds to power off the device when it crashes.
Front/Rear camera
Supports photo taking and quick code scanning.
Scanner
Photo taking and quick 1D/2D code scanning supported.
NFC (optional)
NFC cards can be tapped and read through this.
IC Card Reader
Used for reading chip cards. Dual-sided insertion is supported.
Indicator light
Light indicators used for charging, information, scanning, etc.
· · · · · ·
· · BaseService · ()
· () · · · ·OTA
Volume keys (optional)
Adjusting the volume.
Function keys
You can set a shortcut function.
Type-C
Can be used for charging devices and for developer debugging purposes.
Scan Button
Short press the button to enable scanning function.
Expansion interface (optional)
For connecting related accessories.
Hand starp
Use more conveniently.
Safety Warning
Please insert the AC plug into the AC socket corresponding to the input marked on the power adapter; · This is a class B product. In a residential environment, this product
may cause radio interference. In this case, it may be necessary for the user to take practical measures to address the interference. · Do not operate the device in non-safe areas. · Do not replace the battery when explosive gas may be present. · Do not charge the device in dangerous places. · Battery Replacement: There is a risk of explosion if the battery is replaced by an incorrect type! The old battery shall be given to the maintenance personnel for disposal. Do not throw it into fire!
Caution · Please avoid installation or usage during thunderstorms to prevent the
risk of being struck by lightning. · Please disconnect the power immediately once you find any abnormal
odors, overheating, or smoke.
Suggestions
Do not use the devcie under extreme cold or hot enrionment, such as conditions near fire or lit cigarettes; Do not throw, drop, or bend the device; · Try to use the device in a clean and dust-free condition to avoid
small items falling into the terminal; · Do not use the device near medical equipment without permission; · This device is only suitable for safe use in areas with an altitude of
5000m and below. · Before storing your device for an extended period,please charge the
battery to the optimal level to prevent deep discharge. For instance, if you plan to store the device for more than six months, it’s recommended to charge it to 50% of its capacity every six months.
Statements
The company is not responsible for the following actions: · Damage caused by use and maintenance without the conditions
described in this guide; · The company will not be responsible for any damages or problems
caused by the alternatives or consumables (not the original products or approved products provided by the company). (Without consent of the company. It is not authorized to make product modifications or changes); · The operating system of this product supports official system updates. If the user flashes a third-party ROM system or modifies the system files using cracking methods, it may cause system instability as well as pose security risks and threats.
Disclaimer
Due to product updates, some details of this document may not match the product, please refer to the actual product, and the right to interpret this document belongs to the company. The right to modify this guide without prior notice is reserved.
Pre-installed Software List
· SUNMI App Srore · Launcher · Function Keys Customization · BaseService · Customization Service
(Wallpaper, Boot Animation) · Developer Guidance (Testing Assistant) · User Guide · Startup Guide · Remote Assistance · SUNMI OTA How to check the above software details: select “Settings-Applications”
and select the corresponding software name to view information. To uninstall software, select “Settings-Applications-Manage Applications-
Uninstall” or long-press on the icon and drag it to the “Recycle Bin”.
PRODUCT SAFETY WARNINGS
To prevent possible injury, please read all instructions and safety information before you use the product. Operating temperature: -10 ~ 50 , Storage temperature: -20 ~ 60 .
Battery safety
Charge the battery only at ambient temperatures ranging from 0°C to 45°C. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or an equivalent type of battery recommended by the manufacturer. Dispose of used batteries according to the battery manufacturer’s instructions.
* The product information listed on this page may be updated from time totime due to product upgrades or other reasons. SUNMI reserves the right tomodify the product information and contents on this page without notice.
RF Exposure Statement (SAR)
This device has been tested and meets EU, FCC and IC RSS-102 applicable limits for radio frequency (RF) exposure. Please visit: www.sunmi.com. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter.The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg for body&Head and 4W/kg for extremity averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.The minimum separation distance for body-wom accessories is 10mm, the minimum separation distance for Extremity is 0 mm.
The product SAR limit for Europe is 2.0 W/kg (10g) for head, 4.0 W/kg (10g) for Limb-worn. [Smart POS System,T6F0A/T6F0B] has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification when properly worn on the body (5mm) is 1.25 W/kg , head (0mm) SAR is 0.24 W/kg and Limbs (0mm) SAR is 2.22 W/kg.
Cet équipement a été testé et respecte les limites applicables pour l’exposition aux radiofréquences (RF). Les limites de DAS dépendent de l’utilisation de cet équipement contre la tête ou la main. La limite de DAS IC pour les extrémités est de 4,0 W/kg (10 g) et la limite de DAS pour la tête est de 1,6 W/kg (1 g). La valeur de DAS la plus élevée rapportée selon cette norme lors de la certification du produit en mode tenu à la main est de 1,08 W/kg pour les extrémités (10 mm) et de 0,47 W/kg pour la tête (0 mm).
EU regulatory conformance
Conformity CE Hereby, Shanghai Sunmi Technology Co., Ltd. declares that this device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: https://developer.sunmi.com/docs/read/en-US/maaeghjk480 Product can be operated in at least one Member State without infringing applicable requirements of the use of radio spectrum. (RED article 10.2). INFORMATION ABOUT THE SOFTWARE The description of accessories and components, including software, which allow the radio equipment to operate as intended, can be obtained in the full text of the EU declaration of conformity at the following internet address: https://developer.sunmi.com/docs/read/en-US/maaeghjk480 RESTRICTIONS OF USE 5150-5350MHz only be used by indoor.
Note:In all EU and UK member states,operation of 5150-5350 MHz restricted to indoor use UK(NI) UK IS only. LI NO CH TR
EU Representative:SUNMI France SAS 186,avenue Thiers,69006 Lyon,France
This symbol means that it is forbidden to dispose the product of with normal household waste. At the end of the product life cycle, waste equipment should be taken to designated collection points, returned to the distributor when purchasing a new product, or contact your local authority representative for detailed information on WEEE recycling.
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help.
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ISED Canada compliance statements
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:(1) L’appareil ne doit pas produire de brouillage, et (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
Technology Operation Frequency
GSM900
880-915(TX),925-960(RX)
GSM1800
1710-1785(TX),1805-1880(RX)
WCDMA Band1 1920-1980MHz(TX), 2110-2170MHz(RX)
WCDMA Band5 824-849MHz(TX), 869-894MHz(RX)
WCDMA Band8 880-915MHz(TX), 925-960MHz(RX)
LTE Band 1
1920-1980MHz(TX), 2110-2170MHz(RX)
LTE Band 3
1710-1785MHz(TX), 1805-1880MHz(RX)
LTE Band 5
824-849MHz(TX), 869-894MHz(RX)
LTE Band 7
2500-2570MHz(TX), 2620-2690MHz(RX)
LTE Band 8
880-915MHz(TX), 925-960MHz(RX)
LTE Band 20 832-862MHz(TX), 791-821MHz(RX)
LTE Band 28 703-748MHz(TX), 758-803MHz(RX)
LTE Band 34 2010-2025MHz(TX), 2010-2025MHz(RX)
LTE Band 38 2570-2620MHz(TX), 2570-2620MHz(RX)
LTE Band 40 2300-2400MHz(TX), 2300-2400MHz(RX)
LTE Band 41 2496-2690MHz(TX), 2496-2690MHz(RX)
BT
2402-2480MHz(TX/RX)
BLE
2402-2480MHz(TX/RX)
2.4G WiFi
2412-2472MHz(TX/RX)
5G WiFi
5150-5350MHz(TX/RX)
5G WiFi
5470-5725MHz(TX/RX)
5G WiFi
5725-5850MHz(TX/RX)
NFC
13.56MHz(TX/RX)
GNSS
1559-1610MHz(RX)
EU Power 35dBm 32dBm 25dBm 25dBm 25dBm 25dBm 25dBm 25dBm 25dBm 25dBm 25dBm 25dBm 25dBm 25dBm 25dBm 25dBm 10.34dBm 8.61dBm 19.93dBm 20.68dBm 20.93dBm 13.29dBm 24.90dBV/m@10m /
There is laser light from the scanner, Class 2 laser product, please do not stare into beam. The terminal is not allowed to be maintained or repaired by itself.
ManufacturerShanghai Sunmi Technology Co., Ltd. Room 505,No.388 Song Hu Road, Yang Pu District, Shanghai, China
Documents / Resources
 |
Sunmi T6F0A, T6F0B Smart POS System [pdf] User Manual T6F0A, T6F0B, T6F0A T6F0B Smart POS System, T6F0A T6F0B, Smart POS System, POS System, System |