ITEM NO.：A102009100
WE HAVE YOU IN MIND, LET US SERVE YOU!
Questions? Issues?
CONTACT US
24 hours / 7 days a week
www.sunjoyonline.com
customer.care@sunjoygroup.com
1-(866)-578-6569
Country of Origin: China
Production Number: xxxxxxxxxx
Safety Information
- More than six people are required for this assembly.
- Some parts may contain sharp edges. Wear protective gloves.
- When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Please read all instructions before assembly and usage.
NOTICE: For outdoor use only.
WARNING: Keep all flame and heat sources away from this gazebo fabric. This Gazebo is made with fabric that meets CPAI-84 specifications for flame resistance. It is not fire proof. The fabric will burn if left in continuous contact with any flame source. The application of any foreign substance to the gazebo fabric may render the flame-resistant properties ineffective.
CAUTION: Do not climb on top of the gazebo. Falling off the gazebo can result in serious injury, possibly even death.
DANGER: This unit is heavy! Do not assemble this item alone.
WARNING: While this gazebo is manufactured to withstand winds through only the supplied ground stakes, in areas subject to frequent severe weather, securing the gazebo to a deck, concrete patio or footings should be considered.
Snow must be cleared off regularly during snowy days.
Remove the snow at the top when it is thicker than 4 inches.
In order to avoid damage, use a plastic snow rake to remove excessive snow and ice buildup from roof and keep away from falling debris.
Warranty
1 YEAR WARRANTY
WHAT IS COVERED
This limited warranty is extended to the original purchaser and applies to defects in materials and workmanship of your item provided the item is maintained with care and used only for personal, residential purposes. The item is warranted to be free from defects in material or workmanship for a period of 1 years.
WHAT IS NOT COVERED
We do not reimburse for transportation of delivery costs, or compensate the individual or any outside party for assembling or disassembling the product.
Pre-Assembly
PLANNING ASSEMBLY
Before beginning assembly of this product, make sure all parts are present. Compare parts with the Hardware Included and Package Contents lists. If any part is missing or damaged, do not attempt to assemble the product.
Contact customer service for replacement parts.
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
| Part | Part Number | Description | Quantity | Additional hardware |
| AA | 1–1010020012 | M6 * 20 Bolt | 68 | 4 |
| BB | H050030001 | M6 Flat washer | 294 | 15 |
| CC | H010020011 | M6 * 15 Bolt | 112 | 6 |
| DD | 1–1010020025 | M6 * 60 Bolt | 12 | 1 |
| EE | H040010004 | M6 Nut | 28 | 2 |
| GG | P005100264 | Plastic ring | 52 | 3 |
| HI–1 | H070010003 | Dia. 8 * 180 Stake | 8 | 0 |
| II | 1–1010020021 | M6 * 70 Bolt | 2 | 1 |
| JJ | 1–1010020024 | M6 * 75 Bolt | 16 | 1 |
| KK | H010020022 | M6 * 40 Bolt | 56 | 3 |
| LL | H050020017 | Spring washer | 72 | 4 |
| WW | H090010009 | Wrench | 2 | 0 |
PACKAGE CONTENTS
| Part | Part Number | Description | Quantity |
| Al | P000200449 | Post | 4 |
| B1 | P000100316 | Stake base | 4 |
| C | P006100163 | Stake cover | 4 |
| 03 | P000400862 | Long cross beam (Left) | 2 |
| D4 | P000400863 | Long cross beam (Right) | 2 |
| E3 | P000400860 | Short cross beam ( Right ) | 2 |
| E4 | P000400861 | Short cross beam ( Lett) | 2 |
| Fl | P000501132 | Slanting beam connector | 4 |
| 01 | P000501133 | Middle beam connector 1 | 4 |
| 02 | P000501134 | Middle beam connector 2 | 4 |
| H1 | P000601299 | Slanting beam | 4 |
| 12 | P000601301 | Middle beam 2 | 4 |
| J4 | P000501130 | Big top long connector tube | 2 |
| J5 | P000501129 | Big tap short connector tube | 2 |
| J6 | P000501131 | Big top connector | 4 |
| K | P000601298 | Small roof support beam | 4 |
| L | P000501128 | Small roof connector | 1 |
| M | P000800231 | Small roof cover | 1 |
| N | P005800001 | Hook | 1 |
| P1 | P000700587 | Small roof long panel | 2 |
| P2 | P000700586 | Small roof short panel | 2 |
| 01 | P000700592 | Big roof short side upper panel | 2 |
| 02 | P000700593 | Big roof short side bottom panel (Left) | 2 |
| 03 | P000700594 | Big roof short side bottom panel (Right) | 2 |
| R1 | P000700588 | Big roof long side upper panel (Left) | 2 |
| R2 | P000700589 | Big roof long side upper panel (Right) | 2 |
| R3 | P000700590 | Big roof long side bottom panel (Left) | 2 |
| R4 | P000700591 | Big roof long side bottom panel (Right) | 2 |
| 51 | PO00800231 | Small roof support beam cover | 4 |
| S2 | PO00800233 | Slanting beam cover | 4 |
| S3 | PO00800234 | Middle beam cover | 4 |
| T5 | PO05700639 | Long pipe 1 | 2 |
| T6 | P005700640 | Long pipe 2 | 2 |
| T7 | PO05700641 | Short pipe 1 | 2 |
| T8 | PO05700642 | Short pipe 2 | 2 |
| U | P005000395 | Curve support | 8 |
| V | PO01200204 | Mosquito netting | 1 |
| W1 | PO00601302 | Big roof long side beam | 4 |
| W2 | P000601304 | Big roof short side beam | 4 |
| W3 | PO00601303 | Big roof long side lower beam | 4 |
| W4 | P000601305 | Big roof short side lower beam | 4 |
- Attaching the Stake Bases and Slanting Beam Connectors
Slide the Stake covers (C) over the Posts (A1). Attach the Stake bases (B1) to the Posts (A1) using Bolts (CC) and Flat washers (BB).
Attach the Slanting beam connectors (F1) to the top of the Posts (A1) using Bolts (AA) and Flat washers (BB).
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Connecting the Cross Beams
Attach the Middle beam connectors 1 (G1&G2) on the Cross beams (D3&D4, E3&E4) using Bolts (JJ), Flat washers (BB), Spring washers (LL), and Nuts (EE). Tighten the bolts.
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Attaching the Cross Beams
Attach the assembled Cross beams (D3&D4, E3&E4) to the Posts (A1) using Bolts (AA), Flat washers (BB) and Spring washers (LL). Tighten the bolts.
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Attaching the Curve Supports
Attach the Curve supports (U) to the Posts (A1) and Cross beams (D3&D4, E3&E4) using Bolts (KK), Flat washers (BB) and Spring washers (LL). Tighten the bolts.
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Connecting the Big Roof
Assemble the Big top connector tubes (J4&J5) with the Big top connectors (J6) using Bolts (CC) and Flat washers (BB). Tighten the bolts.
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Attaching the Slanting Beams
Connect the top of the Slanting beams (H1) with the Big top connectors (J6) using Bolts (AA) and Flat washers (BB).
Connect the bottom of the Slanting beams (H1) with the Slanting beam connectors (F1) using Bolts (AA) and Flat washers (BB). Tighten the bolts.
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Attaching the Middle Beams
Connect the top of the Middle beam 2 (I2) with the Big top long connector tubes (J4) using Bolts (AA) and Flat washers (BB).
Connect the bottom of the Middle beam 2 (I2) with the Middle beam connector 1 (G1) using Bolts (DD), Flat washers (BB) and Nuts (EE).
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Attaching the Hook and the Small Roof Support Beams
Insert and screw the Hook (N) tightly into the corresponding hole on the Small roof connector (L).
Attach the Small roof support beams (K) to the Small roof connector (L) using Bolts (DD), Flat washers (BB) and Nuts (EE).
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Attaching the Small Roof
Attach the Small roof support beams (K) to the Big Top Connector (J6) using Bolts (CC) and Flat washers (BB).
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Attaching the Small Roof Panels
Attach the Small roof long panels (P1) and Small roof short panels (P2) to the Small roof frame using Bolts (CC) and Flat washers (BB).
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Attaching the Small Roof Support Beam Covers
Attach the Small roof support beam covers (S1) to the Small roof frame using Bolts (KK) and Flat washers (BB). Then place the Small roof covers (M) in the Small roof connector and secure using Bolts (II) and Flat washers (BB).
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Attaching the Big Roof Beams and the Big Roof Lower Beams
Attach the Big roof short side beams (W2) to the top of the Middle beams 2 (I2) and Slanting beams (H1) using Bolts (CC) and Flat washers (BB). Tighten the bolts.
Attach the Big roof long side beams (W1) to the top of Middle beams 2 (I2) and Slanting beams (H1) using Bolts (CC) and Flat washers (BB). Tighten the bolts.
Attach the Big roof short side lower beams (W4) to the bottom of the Middle beams 2 (I2) and Slanting beams (H1) using Bolts (CC) and Flat washers (BB).
Attach the Big roof long side lower beams (W3) to the bottom of the Middle beams 2 (I2) and Slanting beams (H1) using Bolts (CC) and Flat washers (BB).
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Attaching the Pipes
Attach the Pipes (T5&T6&T7&T8) to the Middle beams 2 (I2) and Slanting beams (H1) using Bolts (CC) and Flat washers (BB).
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Attaching the Big Roof Upper Panels
Attach the Big roof panels (Q1, R1, R2) to the Slanting beams (H) and Middle beams (I) using Bolts (CC) and Flat washers (BB).
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Attaching the Big Roof Bottom Panels
Attach the Big roof panels (Q2, Q3, R3, R4) to the Slanting beams (H) and Middle beams (I) using Bolts (CC) and Flat washers (BB).
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Attaching the Slanting Beam Covers
Attach the Slanting beam covers (S2) to the Slanting beams (H) using Bolts (KK) and Flat washers (BB). Repeat for the Middle beam covers (S3).
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Hanging the Mosquito Netting
Hang the Mosquito netting (V) to the Pipes (T5, T6, T7, T8) using the Plastic rings (GG).
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
- Function du Montage
Attach the assembled pergola to lawn with Stake (HH).
NOTE: To avoid destroying the finish, do not put the parts on the ground directly.
Care and Maintenance
- Our steel components for garden accessories and furniture are treated with rust inhibiting paint that protects it from rusting.
However, due to the nature of steel, surface oxidation (rusting) will occur once these protective coatings are scratched. This is not a defect and thus not covered by the warranty. - To minimize this condition, we recommend care when assembling & handling the product to prevent scratching the paint.
Should any scratching or damage occur, we recommend immediate touch‐up with rust inhibiting paint. - Surface rust can also be easily removed with a very light application of common cooking oil. If surface oxidation (rusting) occurs and if no measure is taken to prevent this, the oxidation may start dripping on to deck or patio and caused damaging stains, which may be difficult to remove. This can be prevented if the above‐mentioned measures are taken to keep the product from oxidizing.
- Use damp cloth to wipe off the stains as quickly as possible.
- If necessary, wash with a mild solution of soap and water; rinse thoroughly and dry completely.
- Periodically check and ensure that all bolts are well‐tighten during use
Limited Manufacturer’s Warranty
Sunjoy Group warrants to the original purchaser that this item is free from defects in workmanship and materials for a period of 1 year from the date of purchase, provided the item was factory-sealed at the time of purchase and is maintained with care and used only for personal, residential purposes. Should any manufacturing defect arise within this warranty period, Sunjoy Group will replace (at our option) any defective merchandise or parts upon proof of purchase; however, transportation and delivery costs, as well as payments to a third party for assembly or disassembly of the item, remain the responsibility of the purchaser. A purchaser of an “open box,” previously-returned, or “clearance” item, as well as original purchasers outside of the warranty period, may obtain replacement parts from Sunjoy Group for products in current production, at nominal cost.
Exclusions
Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of nature, vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of hardware is not covered. Proof of purchase (dated register receipt) is required for warranty claims. Warranty is to the original purchaser and is non-transferable. Any replacement of warranted items will be in the original style and color, or a similar style and color if the original is unavailable or has been discontinued. As some states do not allow exclusions or limitations on an implied warranty, the above exclusions and limitations may not apply. This warranty gives you specific rights, and you may also have other rights, which vary from state to state.
Country of Origin: China
Documents / Resources
 |
SUNJOY A102009100 10x12 Metal Hardtop Gazebo with Netting [pdf] Instruction Manual A102009100 10x12 Metal Hardtop Gazebo with Netting, A102009100, 10x12 Metal Hardtop Gazebo with Netting, Hardtop Gazebo with Netting, Gazebo with Netting |